Question about Cars & Trucks

Open Question

What must the valve clearance of a 1986 Ford Sierra 3.0 GLX be.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22326 Answers

SOURCE: Ford V6 3.0 litre valve clearances

is this a ford V6 essex engine built in dagenham in the late 60s early 70s ? and if so what version zodiac or granada /capri as different camshafts were used with different settings.What condition are the rocker studs in and have they pulled upwards in any way?

Posted on Dec 10, 2012

Ad
  • 883 Answers

SOURCE: I want to know the valve clearance adjustment.

intake .22 to .28 mm
exhaust .27 to .33 mm
rate me solved...this is all I can find

Posted on Jun 27, 2008

  • 54 Answers

SOURCE: Need Valve clearance for '93 kh ford laser

0.10 - 0.15mm inlet
0.18 - 0.23mm exhaust
but you must be carefull because the top of the valve seat becomes concave from wear, a feeler guage will not give the most accurate reading, hope i have been of some hel

Posted on May 14, 2009

johnjohn2
  • 5763 Answers

SOURCE: Valve Clearance

valve clearance, with engine hot, intake valves are .005-.006 in, exhaust valves are .011 in, if engine is cold then its intake .009-.011 in and exhaust is .007. hope this helps good luck.

Posted on Nov 28, 2009

moparownr
  • 667 Answers

SOURCE: i have to adjust valve

What engine do you have (size)? Valve adjustment is generally a thing of the past after the introduction of hydraulic lifters (no adjustment). In 1994 your engine should have hydraulic lifters and are not adjustable. Is this a high performance engine? New camshaft, lifter, and rocker set that are adjustable?

Posted on Aug 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When installing roller rockers on ford f150 5.4 3 valve vin 5 . how many times m,ust i turn the cranckshaft by hand to know im clear of any valve to pistion interference


you open the valve clearance right up as much as you can
any turning with the valve clearance set will bend valves in an interference engine
one the valve timing is set correctly then you adjust the valve clearance

Dec 24, 2017 | Ford Cars & Trucks

1 Answer

I HAVE A FORD SIERRA XR6 3.4LITRE. I NEED THE VALVE CLEARANCE


Hi if valve lifting functions with rockers and push rod tubes basic 12 valve motor intake 0.33 mm exhaust 0.50 mm please do check if rockers, lock nuts and retainers are not worn. settings could be done in 6 steps by rotating engine according fire order of distributor which is 142536

May 09, 2017 | Ford Cars & Trucks

1 Answer

I990 mazda 323 glx valve clearance


With the engine cold, standard valve clearance is 0.010-0.012 in. (0.25-0.31mm) on intake and exhaust sides

Jun 09, 2016 | Mazda 323 Cars & Trucks

1 Answer

Need valve specification on 86 chevy nova


from my 1985/1986 official shop manual:
figure 6A1-39 valve stem and guide clearance
max intake clearance 0.08 mm (0.0031 in)
max exhaust clearance 0.10 mm (0.0039 in)
pg 6A1-17 If clearance is greater than the values given in 6A1-39, then replace the valve and guide

pg 6A1-17
standard overall length
intake 106.88 mm (4.2079 in)
exhaust 106/78 mm (4.2039 in)
do not grind more than 0.5 mm (0.020 in)

Mar 11, 2015 | 1986 Chevrolet Nova

1 Answer

Pls give me correct tappet valve clearance of intake and exhaust for 4G15 mitsubishi lancer


Valve clearance Intake 0.20 mm (Hot- at operating temp)
Valve clearance Exhaust 0.25 mm (Hot).

Feb 12, 2014 | 1986 Mitsubishi Lancer 1.8

1 Answer

Valve clearance for ford v6 3.4l


The valves are hydralic no adjustment is needed.

May 31, 2013 | 1986 Suzuki Samurai

1 Answer

I hav a 1986 mazda B2000, what is the valve clearance pls?


the valve clearance for a 1986 mazda B2000 is, Intake and exhaust valves are .012 inches (.30mm).... Hope this is helpful, have a good day

Mar 18, 2011 | Mazda B2200 Cars & Trucks

2 Answers

Procedure of tappet adjustment


make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl #4.now tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

Mar 14, 2010 | 1986 Suzuki Samurai

1 Answer

How do i adjust the valves in a ford 1997tarus with a 3.0 ohv


Valve Stem to Guide Clearance · Intake
0.026-0.071 mm (0.001-0.0028 in) · Exhaust
0.038-0.083 mm (0.0015-0.0033 in) Valve Clearance
  1. With No. 1 piston (6108) on top dead center (TDC) at the end of compression stroke (Position No. 1 in the illustration), check the following valves:
    Position 1
    No. 1 exhaust valve (6505) No. 1 intake valve (6507).
    No. 3 exhaust valve No. 2 intake valve.
    No. 6 exhaust valve No. 4 intake valve.
  1. Rotate crankshaft (6303) 360 degrees to position No. 2 and check the following valves:
    Position 2
    No. 2 exhaust valve No. 3 intake valve.
    No. 4 exhaust valve No. 5 intake valve.
    No. 5 exhaust valve No. 6 intake valve. 4cb038f.gif

Oct 19, 2009 | 1997 Ford Taurus

6 Answers

1993 mitsubishi pajero exceed-intercooler turbo 2800 diesel engine 4m40


Hi, I have a Pajero 2800 Turbo 1995 Auto. It has developed a bad oil leak somewhere around the front right hand side (from the front) where there seems to be oil spraying over the pipes, etc. Can't see it happening with the engine running and have cleaned the engine off but still can't see where it comes from. It has emptied the sump! Any ideas?
Cheers,
Rob.

Jul 10, 2008 | 1995 Mitsubishi Montero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14445 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...