Question about 2006 Mahindra Bolero Single

Open Question

Routing of fan belt on all pulleys

Routing on all pulleys and tensioning diagram

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you check the timing belt for a Lincoln navigator?


It is a big process
  • Open the hood. Disconnect the negative (black) battery cable.

  • 2

    Inspect the fan shroud for the accessory belt routing diagram. If the diagram is missing or illegible, use a pen and paper to draw your own diagram before removing the belt. The new belt must be routed around the pulleys exactly as the old one was.


  • Locate the spring loaded belt tensioner on the front of the engine. There is a small pulley attached to the bottom of the tensioner arm.

  • 4

    Slide the square end of the breaker bar into the square hole in front of the tensioner pulley. Rotate the breaker bar counterclockwise and the entire tensioner will move enough to relieve the tension from the belt. Pull the belt out from under the pulley and slowly let the breaker bar retract.

  • 5

    Remove the accessory belt from each pulley with your hands. Rotate one of the fan blades to the top side of the engine with your hand and pull the belt around it. Repeat this process until the belt is around all of the fan blades. Pull the belt out of the engine compartment.

  • 6

    Route the new belt carefully around each fan blade. Wrap the belt around the crankshaft pulley to begin the belt routing process. Refer back to the belt routing diagram instructions to properly route the new belt around the accessory pulleys.

  • 7

    Turn the tensioner counterclockwise again with the breaker bar. Position the new belt evenly under the tensioner pulley. Allow the tensioner pulley to tighten against the belt. Pull the breaker bar out of the tensioner.

  • 8

    Reconnect the negative battery cable.

  • 9

    Start the engine for five to ten seconds to seat the new belt. Turn the engine off. Visually check that the belt is properly seated around all pulleys.


  • Performance Chip

    May 24, 2012 | Cars & Trucks

    1 Answer

    Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


    Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    Replacing fan belt?what tools are required?


    Instructions

    Things You'll Need
    3/8-inch drive breaker bar
    Metric sockets
    Serpentine belt

    1 Open the hood and inspect the flat surface on top of the plastic fan shroud for the belt routing diagram. Follow the diagram instructions to route the new belt.

    2 Locate the serpentine belt self-adjusting tensioner on the front of the engine block. The tensioner has a pulley on the bottom of the tensioner arm, which the belt travels under. The tensioner can only be rotated from the bolt that secures the pulley to the tensioner arm.

    3 Rotate the tensioner in a clockwise motion with a metric socket and the breaker bar to loosen the tension from the belt. Then, pull the belt off the top of the tensioner pulley. Release the tensioner pulley and pull the breaker bar off the pulley bolt.

    4 Pull the belt out of the accessory pulleys. Then, slide the belt around each fan blade and out of the engine bay. Rotate each fan blade to the top side of the engine to get the belt around each fan blade.

    5 Match both the new belt and the old belt together to make sure that the new belt is the correct size. Then, route the new belt around each fan blade and around the crankshaft pulley. The crankshaft pulley is the big pulley at the very bottom of the engine.

    6 Follow the routing directions from the belt routing diagram to install the new belt around the other accessory pulleys. Once the belt has been routed around all of the pulleys, look over the belt and make sure that it is secure inside all of the pulleys.

    7 Crank the 1998 Dodge Caravan and let the motor run for about 15 seconds. This will finish seating the ridges of the new belt into the grooves of each accessory pulley.

    8 Shut the motor off and close the hood.

    Jul 07, 2011 | 1998 Dodge Caravan

    1 Answer

    How to replace timing belt on a 2003 chevy tracker


    Open the hood and locate the accessory belt routing diagram that is stamped to the top flat surface of the radiator shroud. Use the routing diagram to properly route the new belt around each accessory pulley.
    Look on the front of the engine between the alternator and the power steering pump and locate the automatic belt tensioner. Use the pulley that is attached to the end of the tensioner to loosen the tension from the belt.
    Position a breaker bar and a 14 mm socket onto the bolt head in the middle of the tensioner pulley. Turn the breaker bar clockwise to loosen the tension from the belt. Slide the belt off of the tensioner pulley and slowly release the breaker bar.
    Slide the belt out from around all of the engine accessory pulleys. Pull the belt around each of the fan blades and up out of the engine compartment.
    Slide the new belt around each of the fan blades and around each of the accessory pulleys as directed by the belt routing diagram.
    Turn the tensioner clockwise with the breaker bar and the 14 mm socket again. Slide the belt around the tensioner pulley and slowly release the breaker bar. Pull the breaker bar and socket off of the tensioner and out of the engine compartment.
    Crank the engine for ten to fifteen seconds to finish seating the ribs on the inside of the belt to the grooves of each accessory pulley. Turn the engine off.

    Feb 20, 2011 | 2003 Chevrolet Tracker

    1 Answer

    I need to replace the serpentine belt on my car. How do I do that?


    These instructions will help you . and also the picture below will help you more.
    1
    Locate the belt-routing diagram, printed on the fan shroud or possibly applied to the underside of the hood. This diagram shows you how to properly route the new belt, as well as identifying the location of the various pulleys, including the serpentine belt tensioner.
    2
    Move the belt tensioner off the Sable's belt using the serpentine belt tool. The tool connects to the side of the tensioner's arm and essentially acts as a handle for use in moving the tensioner. You can purchase a serpentine belt tool at most auto-part retailers.
    3
    Slip the belt away from the tensioner with your free hand and release the pressure on the tensioner with the tool. Pull the belt off the rest of the pulleys by hand and then remove it from the engine well.
    4
    Grab the old belt and new belt with one hand and put your foot through the other end of the belts. Stretch them both to their full length and check to ensure their both the same size. The old belt may have up to one-inch of extra length due to normal stretching that occurs during the belt's service life.
    5
    Wind the new belt, rib side to the pulley, around the crankshaft pulley. Consult the routing diagram and route the belt to the next pulley on the diagram. Continue to route and then check the diagram until you have the belt wound around every pulley except the belt tensioner pulley.
    6
    Double check to make sure the belt routes exactly as shown on the diagram and then move the tensioner aside once more so you can route the belt over the tensioner pulley as shown in the diagram. Move the tensioner back into place slowly and remove the tool.

    Good luck

    tgv1501_23.jpg




    Jan 03, 2011 | 1996 Mercury Sable

    1 Answer

    Replace alternator


    The alternator belt on the 1999 Dodge Caravan also controls the air conditioner compressor, the water pump and the power steering pump. The belt is called a serpentine belt, and it is designed to fit around all of the accessory pulleys at the same time. As the belt travels around each accessory pulley, it enables the accessory to operate. Once the belt is damaged, cracked or frayed, you should change it before it breaks. If that happens, each of the accessories will stop working.

    Open the hood and prop it up so that it does not fall. Engage the parking brake.

    Inspect the top surface of the fan shroud for the serpentine belt routing diagram. Follow the routing instructions on the diagram to install the new belt.

    Locate the serpentine belt self-adjusting tensioner on the front of the engine. The tensioner is directly below the alternator. Use the bolt that connects the tensioner pulley to the tensioner arm to rotate the tensioner.

    Turn the tensioner device counterclockwise to move the tensioner. This will relieve the tension from the belt. Once the belt has enough slack in it, slide the belt out from under the tensioner pulley.

    Lift the belt off each accessory pulley. Slide the belt around the fan blades and out of the engine area.

    Lay the old belt next to the new belt to ensure that the new belt is the correct width and length. Slide the belt around the fan blades and around the crankshaft pulley on the bottom of the engine.

    Follow the belt routing diagram to position the belt around the air conditioner compressor pulley, the power steering pump pulley, the water pump pulley and the idler pulley. Once the belt is routed inside each accessory pulley, inspect the belt to make sure that it is securely inside the pulleys.

    Crank the 1999 Dodge Caravan for 10 to 15 seconds to completely seat the belt ribs in the grooves on each accessory pulley. Shut the engine off and close the hood.

    If the belt routing diagram for the 1999 Dodge Caravan is missing, use a pen and a notepad to draw the exact routing of the old belt and use it when installing the new belt.

    Nov 26, 2010 | 1999 Dodge Caravan

    1 Answer

    Diagram for fan beltover pulleys


    1. The fan belt routing diagram for 2004 Volkswagen Bora 1.4 16V

    tdisline_26.jpg

    2. The fan belt routing diagram for 2004 Volkswagen Bora 1.6 16V

    tdisline_27.jpg

    3. The fan belt routing diagram for 2004 Volkswagen Bora 1.8 Turbo


    tdisline_28.jpg

    4. The fan belt routing diagram for 2004 Volkswagen Bora 2.0

    tdisline_29.jpg

    5. The fan belt routing diagram for 2004 Volkswagen Bora 1.9 TDI

    tdisline_30.jpg
    CS = Crankshaft
    Gen = Alternator
    G = Guide pulley
    T = Tensioner pulley
    AC = Air Conditioning
    PAS = Power Assisted Steering

    Nov 25, 2010 | 2004 Volkswagen Jetta

    1 Answer

    JUST A DIAGRAM OF THE SERPENTINE BELT ROUTE


    The diagram can be found here.
    Remove the upper fan shroud and aircleaner assemblies for easy access.
    To release tension on the belt turn the tensioner pulley nut clockwise and slip the belt off the alternator pulley. To refit the belt route as shown over every pulley except the alternator, once again release the tensioner and fit the belt to the alternator. See that the belt is properly seated over every pulley before restarting the engine.

    Nov 11, 2010 | Isuzu VehiCROSS Cars & Trucks

    2 Answers

    How to adjust de belt to grand cherokee 8 cilinders 4.7


    1. Step 1 Find the belt tensioner pulley. The tensioner pulley is generally between the crankshaft and a component toward the top of the hood area.
    2. Step 2 Check the belt routing so you know how to replace the belt. You may be able to find a belt routing diagram on a decal on the fan shroud or in support documentation. Otherwise, make you own sketch for reference.
    3. Step 3 Rotate the belt tensioner pulley, using the wrench, to and relieve tension on the belt.
    4. Step 4 Slip off the old belt and slowly release the tensioner pulley.
    5. Step 5 Use your belt routing diagram to put the new belt onto all of the pulleys. Pay close attention to the water pump pulley, as incorrect routing can cause the water pump to run backwards and overheat.
    6. Step 6 Make sure the belt is correctly routed and seated on all pulleys. Rotate the tensioner again to allow for the belt to slip onto all pulleys and then release the tensioner again to regain correct tension on the belt.

    Jun 01, 2010 | 1999 Jeep Grand Cherokee

    1 Answer

    How to install serpantine belt on a 1995 Jeep Cherokee 6-cylinder


    Hi there. Here is a Step by Step guide that will help you replace your serpentine belt.




    Step1 Find the belt tensionermag-glass_10x10.gif pulley. The tensioner pulley is generally between the crankshaft and a component toward the top of the hood area. Step2 Check the belt routing so you know how to replace the belt. You may be able to find a belt routing diagram on a decal on the fan shroud or in support documentation. Otherwise, make you own sketch for reference. Step3 Rotate the belt tensioner pulley, using the wrench, to and relieve tension on the belt. Step4 Slip off the old belt and slowly release the tensioner pulley. Step5 Use your belt routing diagram to put the new belt onto all of the pulleys. Pay close attention to the water pumpmag-glass_10x10.gif pulley, as incorrect routing can cause the water pump to run backwards and overheat. Step6 Make sure the belt is correctly routed and seated on all pulleys. Rotate the tensioner again to allow for the belt to slip onto all pulleys and then release the tensioner again to regain correct tension on the belt.

    Please rate and god bless.


    Mar 25, 2009 | 1995 Jeep Cherokee

    Not finding what you are looking for?
    2006 Mahindra Bolero Single Logo

    Related Topics:

    32 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mahindra Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    sachin sharma
    sachin sharma

    Level 2 Expert

    171 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17130 Answers

    Are you a Mahindra Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...