Question about Cars & Trucks

Open Question

Diagram for bmw 328i engine compartment - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

countrysi248
  • 443 Answers

SOURCE: I have a 1998 bmw 328i and the central locking sytem doesnt work.

does it have a remote on your key chain also ? if so does it work if you push the unlock two times ? if not then you might just have a bad switch in the console. and if you checked all the fuses and relays under the hood its just down to checking to see if you have power at the switch you talked about on the console . pop the switch out of the console and with the key on see if you have power there with a tester.. if power is there then replace the switch .. thanks and holler if you need more Jerry

Posted on Apr 12, 2009

  • 840 Answers

SOURCE: 1998 BMW 328i Rear WIndows broken

then it is the actual buttons for the windows on the rear doors

Posted on Apr 12, 2009

  • 1 Answer

SOURCE: 2000 BMW 328i fusebox diagram

I have 1998 BMW 328i and it shut off entire air condition system while running. sometime it works fine then suddenly it shut off while driving.

Posted on Jun 29, 2009

  • 490 Answers

SOURCE: 2000 BMW 328i yellow oil light on but oil is fine

Your sensor is going bad or you have to change your oil.

Posted on Jul 29, 2009

ZJLimited
  • 17970 Answers

SOURCE: BMW 328i Starter how to replaice

1999 BMW 328I 2.8L EFI DOHC 6cyl

Starter - Removal & Installation

The starter motor on some models is very difficult to see from the top of engine compartment as it is covered by the intake manifold. On these models, without removing the intake manifold, the starter motor must be removed from underneath the vehicle. Because the starter motor mounting bolts are not easy to access, a long extension with a universal joint mounted on a proper sized socket could be used. A three foot transmission extension is commercially available from tool vendors that has a 3 / 8 inch drive of the driven end and 1 / 2 inch drive on the drive end. If used with a non-binding impact universal joint and a proper fitting impact socket, the starter motor fasteners can be removed from underneath the vehicle.
Once the starter motor fasteners are removed, the starter motor may have to be moved side-to-side several times to loosen the dowel pin if it has corroded in place.

NOTE When the battery is disconnected, the radio code, on-board computer and clock settings will be lost. The radio code should be obtained before disconnecting the battery or radio. Once the battery has been reconnected, the radio will not function unless the code is keyed in.
Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm)
Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) Starter motor electrical terminal fastener torque specifications for all models:
M5 terminal fasteners: 44 inch lbs. (5 Nm)
M6 terminal fasteners: 53 inch lbs. (6 Nm)
M8 terminal fasteners: 115 inch lbs. (13 Nm) Starter motor mounting fasteners:
Hex head bolts: 36 ft. lbs. (49 Nm)
Torx bolts: 32 ft. lbs. (43 Nm) E36 6-Cylinder Engines
Automatic Transmission Models

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Remove the climate control air intake duct at the rear of the engine compartment as follows:
    1. Release the grille clips at the rear and lift the grille upward from the rubber seal, then remove the seal.
    2. Remove the two self tapping Phillips screws from inside the duct to release the electrical harness housing.
    3. Press the electrical housing downward to expose and remove the two hex head self tapping screws on each side of the duct and lift the duct up and out of the engine compartment.
  5. Remove the intake manifold trim and valve cover trim covers.
  6. Disconnect the ignition coil electrical connectors and ground straps, label for reinstallation and place aside.
  7. Remove the two fasteners that secure the fuel injection electrical connector harness to the rail. Remove the harness and carefully place aside toward the back of the engine compartment behind the right side strut tower.
  8. Remove the intake manifold.
  9. Remove the electrical leads from the starter motor and place aside.
  10. Remove the starter motor mounting fasteners at the transmission bell housing, then remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket, then lift the starter motor upward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.
Manual Transmission Models
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Set the ignition switch to the OFF position.
  3. Disconnect the negative battery cable.
  4. Raise and safely support the vehicle.
  5. Remove the fasteners for the reinforcement mounted between the frame rails just behind the rear lower control arm bushing brackets. Mark the bar-s direction for proper reinstallation and remove the bar.
  6. Remove the fuel line cover located near the left side rear lower control arm bushing bracket.
  7. Release the fuel lines and reverse light wiring from their routing brackets.
  8. Note the routing of the starter motor electrical wires, remove the wire mounting nuts, and place the wires aside.
  9. Remove the top and bottom starter motor to engine-transmission mounting fasteners.
  10. Remove the two mounting nuts at the L-shaped mounting bracket.
  11. Loosen the L-shaped bracket to engine block mounting bolt slightly, then remove the bolt while supporting the starter motor.
  12. Remove the bracket and carefully lower the starter motor downward away from the engine.
  13. Visually inspect the starter pinion and ring gears for any signs of damage.
  14. Installation is in reverse order of removal.

Fig. A view of the starter motor mounting fasteners and dowel pin. The mounting bolts are threaded into the starter motor

cd45991.jpg

Fig. The starter motor mounting bolts are a different size than the transmission-to-engine mounting bolts

2cbfa11.jpg

I hope help you with this (rated this help) Good luck.

Posted on Sep 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got a p0597 code on my 2012 bmw 328i


That is a code for the electronically controlled engine thermostat. Have checked asap before you do very expensive damage to your engine.

Jul 26, 2016 | 2012 BMW 3 Series 328i Sedan 2.0L 4-cyl....

1 Answer

Eml came on in my bmw 328i 1999 please how to fix this problem


First thing you need to do is to have the car scanned with a engine malfunction light scanner . then you'll get a engine trouble code.

depending on what is the code then search on google for bmw 328i 1999 engine trouble code list and repair procedures.


to find out what codes meens go to that link http://www.obd-codes.com/trouble_codes/bmw/.

Nov 09, 2015 | BMW Cars & Trucks

1 Answer

What helps with noisy engine lifters on 2008 bmw 328i coupe?


You will have to do a valve clearance set, a mechanic will know how to do this, hope this helps

Aug 30, 2014 | 2008 BMW 328xi Coupe

1 Answer

WHERE IS AIR FILTER IN BMW 328I 1997


It's located left side of the engine compartment in the Box, release to two clips and slide it out.

Sep 14, 2009 | 1997 BMW 328

1 Answer

2000 BMW 328i fusebox diagram


I have 1998 BMW 328i and it shut off entire air condition system while running. sometime it works fine then suddenly it shut off while driving.

Jun 26, 2009 | 2000 BMW 3 Series

1 Answer

How to remove the switch button for the CD Player on BMW 328i


try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 12, 2009 | 2007 BMW 328xi Sports Wagon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...