Question about Toyota Previa

Open Question

Floor jack point - Previa Toyota Cars & Trucks

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 160 Answers

SOURCE: jacking points on 1998 cavalier

about 4 inches behind front wheels and about 4 inches in front of rear wheels

Posted on Nov 12, 2008

Ad
bdubsee
  • 75 Answers

SOURCE: lift points on chassis for a floor jack

I use exactly the same the jacking points as I would use with the factory scissor jack. They are reinforced to handle the load. You'll find these point marked with triangle stamped into the rail and in your owner's manual.

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jacking points


Correct jack points Jaguar Forums Jaguar Enthusiasts Forum

should be what your looking for plus other advice etc , forums are an excellent resource keep me updated if ok or not

May 26, 2014 | 2008 Jaguar Xkr

1 Answer

Where do i place the floor jack if the safety stands are going to be supporting by the frame


operators guide , shows jack points, (under change tires)
or
FSM
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

on the axle tubes.
or the frame.
do not jack up to suspension points, or any swaybar /track rods.

Jan 31, 2014 | 2000 Jeep Grand Cherokee

1 Answer

Jacking point for 2008 xb?


on front, I put my jack near the frame member, on the rear it is the same, on the carrier frame

Jan 12, 2014 | 2008 Scion Xd

1 Answer

1985 toyota supra jacking points


There is a plate under the steering rack behind the sump.

Oct 09, 2012 | 1985 Toyota Celica Supra

1 Answer

My 2 stage floor jack raises to load point, butbut no further -- at this point you cannot pump the handle


raise the head all the way up remove plug and fill with hyd fluid replace plug and try to jack it should go all the way up...i had same problem..

Feb 27, 2012 | Cars & Trucks

1 Answer

What are the factory jack/lift points for a 2005 Buick Lesabre when using a floor jack


the same as your jack in the trunk, along the rocker panel you will see a spot to set the jack. see the owners manual, Usually... just a few inches behind the front wheel and a few inches ahead of the rear wheel. it kind of looks like a tab, thats where the rocker is reinforced.

Aug 27, 2011 | 2002 Buick LeSabre

1 Answer

Where do i place a jack stand on a 1995 Jeep Grand Cherokee?


Hope this helps and please don't forget to rate...thanks!

Jacking points on all Jeep vehicles



c17hydro_1.gif

Your Jeep was supplied with a jack for emergency road repairs. This jack is fine for changing a flat tire or other short-term procedures not requiring you to go beneath the vehicle. Do not attempt to use the jack on any portions of the vehicle other than specified by the vehicle manufacturer. Always block the diagonally opposite wheel when using a jack.



c17hydro_2.gif

Placing a floor jack under the front frame rail



c17hydro_3.gif

Placing a floor jack under the rear frame rail at the leaf spring shackle. It may be necessary to place a block of wood between the frame rail and the jack



c17hydro_4.gif

Supporting the front of the vehicle with jack stands placed under each frame rail


A more convenient way of jacking is the use of a garage or floor jack. You may use the floor jack at the specified points in following the illustrations.

Never place the jack under the radiator, engine or transmission components. Severe and expensive damage will result when the jack is raised. Additionally, never jack under the floorpan or bodywork; the metal will deform



c17hydro_5.gif

Support the rear of the vehicle using jack stands placed underneath each side of the rear differential (inset photo)

Nov 04, 2010 | 1995 Jeep Grand Cherokee

2 Answers

Where to place the jack to change front passenger wheel?


if its a floor jack or the stock jack place it on the pince well at the bottom of door about 6 inch from frt of fender,put e-brake on when jacking car,heres a diagram to show you the four points, hope this helps.0cc328e.gif

Mar 29, 2010 | 1996 Chevrolet Cavalier

2 Answers

Lift points on chassis for a floor jack


I use exactly the same the jacking points as I would use with the factory scissor jack. They are reinforced to handle the load. You'll find these point marked with triangle stamped into the rail and in your owner's manual.

Dec 14, 2009 | 2008 Saturn Aura

1 Answer

Jacking points on 1998 cavalier


about 4 inches behind front wheels and about 4 inches in front of rear wheels

Nov 11, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...