Question about Chevrolet Silverado 1500

Open Question

1998 Chevy C1500 Suburban 5.7L Vortec Crankshaft position sensor location

I need to know the exact location of the crankshaft position sensor on the 98 chevy suburban with the 5.7l vortec. its driving me crazy!

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: where's the crankshaft position sensor located in 98 plymouth voy

Guessing it's a 6 cyl, 3.0L, but should be located on transaxle housing above vehicle speed sensor.c937fe4.jpg

Posted on Sep 08, 2009

ZJLimited
  • 17970 Answers

SOURCE: crankshaft position sensor location

1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.

87c675c.jpg

Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship

Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.

I really hope help you wuth this (rated this help). have a nice day, good luck.

Posted on Sep 25, 2009

Testimonial: "Awesome. Thanks."

roniecon
  • 6826 Answers

SOURCE: were is the crankshaft position sensor located on 2001 chevy mali

It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Posted on Mar 22, 2010

BCAS1298
  • 3092 Answers

SOURCE: where is oil pressure guage sending unit located

On top of the engine, to the back, below the distributor.

Posted on Sep 16, 2010

  • 163 Answers

SOURCE: need to know location of ecmon my 1996 chevy

It is located under the hood on the drivers side right next to the fender. It's between the Fender and the Brake Control module. It's called the Vehicle Control Module (VCM) in this diagram.

dirus42_0.jpg

Posted on Dec 27, 2010

Testimonial: "Thank you for your info. It was very helpful!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do replace ignition control module in 1998 K-1500 5.0 liter vortec


This system does not use the ignition module used on the DI systems in the past. The VCM controller now controls the ignition control (IC) and bypass functions.
The crankshaft sensor, located in the front engine cover, is perpendicular to a target wheel attached to the crankshaft. The target wheel is equipped with slots situated 60 degrees apart. As the crankshaft rotates, the target wheel rotates past the crankshaft position sensor. The rising and falling edges created by the slots cause a signal to be sent back to the VCM. This signal occurs three times per crankshaft revolution and is referred to as the 3x signal for V6 applications. The signal occurs four times per crankshaft revolution and is referred to as the 4x signal for V8 applications.
The VCM then utilizes this 3x (V6) or 4x (V8) signal in order to provide the correct spark to the engine by way of the single coil driver module. The single coil driver module is basically an electronic switch that when commanded by the VCM, causes the primary coil voltage to breakdown, energizing the secondary coil and providing a spark via the coil wire to the distributor cap. The distributor consists of the following components:
The system consists of the following components:
?€¢
Vehicle control module (VCM)


?€¢
Distributor


?€¢
Ignition coil driver module


?€¢
Ignition coil


?€¢
Crankshaft position (CKP) sensor


Now which part do you want to replace ?

?€¢
Cap and rotor


?€¢
Camshaft position sensor


?€¢
Gear drive and shaft

The camshaft drives the distributor shaft which rotates providing a spark to the correct cylinder by way of the cap and rotor. The camshaft position (CMP) sensor functions much like the crankshaft sensor previously described but provides only a 1x signal to the VCM. That is, for every 2 rotations of the crankshaft, there is 1 rotation of the camshaft. Note that the camshaft position sensor will not affect driveability. The sole purpose of the camshaft position sensor is to provide the VCM with the necessary information for the misfire diagnostic trouble codes (DTCs).

Sep 06, 2015 | 1998 Chevrolet K1500

1 Answer

Crankshaft Position Sensor location


It should be right below the harmonic balancer or crankshaft pulley on the engine block

Aug 04, 2014 | 2009 Chevrolet Suburban

2 Answers

Location crankshaft sensor 96c1500 5.7ci


CRANKSHAFT POSITION SENSOR LOCATED NEXT TO THE STARTER.

Sep 16, 2011 | 1996 Chevrolet C1500

1 Answer

Where is the crankshaft position sensor on a 2006 chevy trailblazer 4.2 lL vortec?


Hello rentmyhubby3,

The crankshaft position sensor is on the lower left hand side (drivers side) of the engine. See image below.

netvan_27.png


Regards,
netvan

Mar 20, 2011 | 2006 Chevrolet Trailblazer

1 Answer

Location of crankshaft sensor for 2000 chevy silverado 6.0 vortec?


The crankshaft position sensor is located on the top rear center of the engine near the bell housing.
Hope this helps.

Nov 21, 2010 | 2000 Chevrolet Silverado 2500

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

2 Answers

Were is the crankshaft position sensor located on 2001 chevy mali


It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Mar 22, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

Code p1345 and po300 #3#6 missfere on 2001 chevy astrovan 4.3


P1345 Crankshaft Position - Camshaft Position Correlation

Either one of these sensors is bad or your timing chain/belt has skipped.

Mar 04, 2010 | 1998 Chevrolet C1500

1 Answer

Where is the crankshaft sensor located on a 1998 chevrolet silverado 5.7 L


The Crankshaft Position Sensor (CKP) is located at the lower front of the engine on the engine front cover, also called the timing cover. Through a use of magnetic pulsation, the CKP sensor provides the PCM (control module) with a crankshaft position signal. The PCM uses that signal to determine the spark sequence (firing order) for each cylinder. It also uses the signal to precisely control ignition timing and calculate engine speed, etc. Easy fix and clean the area out first with brake cleaner before working around that area and take care not to break the tab on the wire harness that connects to the crank sensor. Good luck

Dec 16, 2009 | 1998 Chevrolet C1500

1 Answer

Where is the distributor located on a 1999 5.3L chevy vortec engine


There is no distributor. Firing is controlled by the computer which gets signals from crankshaft position sensor and camshaft position sensor for firing and timing.

Apr 29, 2009 | 2000 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...