Question about 2001 Chevrolet Silverado 1500

Open Question

Color code for ckp sensor 4.3l 01 chevy

Pigs\tail separated need color code for positions a b c on pigtail I have yel green and blue

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tepfy
  • 319 Answers

SOURCE: Where do color wires connect on crank position sensor Chevy 2000?

http://www.autozone.com/N,317019/initialAction,repairGuide/shopping/repairGuideVehicleSelect3.htm

follow this and figure out what truck you have. then put in the part you want and go to repair info on the left. It should give you the diagram you need.

Posted on Dec 20, 2008

Ad
motor1258
  • 6674 Answers

SOURCE: I need to know the color code of my Chevy Blazer 2000 it is green

Check for sticker in glove box. Bunch of numbers & letters, usually last line.(bottom line)

Posted on Jan 23, 2009

inf12
  • 13 Answers

SOURCE: need wiring diagram for taillights on 2000 chevy venture van

d7d3cd6.jpg3a50d5e.jpg80738de.jpg8d3e722.jpg GOOD LUCK

Posted on Feb 08, 2009

  • 366 Answers

SOURCE: 97 Chevy Astro van lugs, like it misses, B4 finally cranking on

crank shaft sen. is easy enough to change.its mounted near timing chain cover,cam sen.is somewhat harder,its in the distributor,id doubt that both are defect

Posted on Mar 10, 2009

  • 713 Answers

SOURCE: how do i replace tail light harness with socket in a cavalier 01

if you have a complete replacement harness it unplugs behind the felt in the trunk. if it is just a socket with a pigtail clip wires about an inch from old socket and use but splice connectors and use electrical tape to cover them back up with.

Posted on Aug 26, 2009

Testimonial: "thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Color code wiring for 2007 dodge 3500 4x4 tail lights and reverse light


Left
TAIL/STOP/TURN lamp: WHT/DK GRN
TAIL/TURN lamp: WHT/YEL
BACK-UP lamp: WHT/LT GRN

Right
TAIL/STOP/TURN lamp: WHT/YEL
TAIL/TURN lamp: WHT/GRY
BACK-UP lamp: WHT/LT GRN

Sep 16, 2016 | Dodge Ram 3500 Cars & Trucks

1 Answer

How to change crankshaft sensor on a 2001 cad catiera


Its on the side of the block firewall side ... REMOVAL Numbers in text in parenthesis correspond to numbered components in image. Disconnect the wiring harness (1) from the Crankshaft Position (CKP) sensor pigtail. Securely attach a scrap piece of wire about 36 inches long to the CKP sensor pigtail. Later, this piece will be used as a pull wire to guide the new sensor pigtail back through the same routing. Raise and support the vehicle. Remove the oil filter and capture any lost engine oil in a container. Loosen the oil cooler lines at the engine block. Back out the fittings far enough in order to gain sufficient clearance for the sensor pigtail connector to pass between the oil cooler lines and the side of the engine block. Remove the fastening bolt for the CKP sensor (1). Remove the CKP sensor and the O-ring seal from the engine block. Remove the CKP sensor pigtail. Observe the routing of the pigtail. Gently pull the CKP sensor pigtail down through the routing path and out. Guide the pigtail connector along the top of the oil cooler lines around to the side of the engine block. Pass the connector between the lines and the block at the point of the widest gap. Stop when the pull wire is exposed at both ends of the routing path. Disconnect the sensor from the pull wire. INSTALLATION Securely attach the CKP sensor pigtail to the lower end of the pull wire. Pass the pigtail connector between the oil cooler lines and the engine block. Using the pull wire as a guide, pull the sensor pigtail along the top of the oil cooler lines and around to the rear of the engine. Use the pull wire to pull the pigtail into position. Disconnect the pull wire from the sensor pigtail. Connect the sensor pigtail to the harness connector. Thoroughly clean the mating surfaces of the CKP sensor and the engine block. Install the CKP sensor with a new O-ring seal into the engine block. Install the fastening bolt (1) for the CKP sensor. Check the harness for proper routing. Make sure that the wiring cannot come in contact with the exhaust manifold. Tighten the oil cooler lines at the engine block. Install the oil filter. Lower the vehicle. Recheck the engine oil level.

Jun 22, 2016 | 2001 Cadillac Catera

1 Answer

What wire from the engine harness grey or brown goes to the blue signal wire on the 02 sensor


posted now 3 times.
no engine stated (of the 3)
no symptoms stated. or job.
front or rear , oBD2 sensor not stated.
on your other post, i answred for all 3 engine
front 02 sensor B1S1.
all 3 engines, the ECU schematics on the 02 pins.

go back and read. your other posts.

Feb 28, 2016 | 1997 Geo Prizm

1 Answer

What does check engine light P2138 code mean and how to fix it?


P2138 Throttle/Pedal Pos Sensor Voltage Correlation

Potential Causes of P2138 DTC It's been my experience that the wiring connector or "pig tail" on the throttle body gives problems in the form of a poor connection.The female terminals on the pigtail corrode or pull out of the connector. Possible bare wire on pigtail shorting to ground. The top cover on the throttle body distorted preventing the gears from turning properly. The electronic throttle body is faulty. The accelerator pedal sensor or its wiring failed. The engine management computer has failed. The TPS sensors were not correlating for a few seconds and the computer needs to be cycled through its relearn phase to restore active response to the throttle body, or the computer needs reprogramming at the dealer.

Apr 05, 2013 | 2006 Cadillac CTS

2 Answers

Hey,I have an 03 chevy s10,I recently tried putting a pig tail on it (straight wired) and had no luck,gave up and crimped all the wire back together,and today a guy at work noticed I had no taillights,but...


I would check your tail light fuse first then test the brown wire in the tail light harness where you origionally cut into it. With the lights on there should be around 12v on it. if not you may have pulled the wire too hard and broke it upstream. Test to see if there is 12v at the fuse ad if there is, your trouble should be in the wire between the fuse and the spot where you cut into it.

Mar 25, 2013 | Cars & Trucks

1 Answer

5 pin trailer wiring diagram 91 Ford panel van


Please let me know if you have questions, and thanks for using FixYa.

Function Pigtail color Van color
right turn green orange
left turn yellow light green
ground white black
tail/marker brown brown
brake blue



jturcotte_1071.gif

Feb 19, 2011 | Ford F Cars & Trucks

1 Answer

Rewiring 1968 cutlass I need color codes


The wire color code is as follows:

BLK= Black

BRN= Brown

RED= Red

ORG= Orange

YEL= Yellow

GRN= Green

BLU= Blue

GRY= Grey

WHT= White

PPL= Purple

PNK= Pink

TAN= Tan

LT BLU= Light Blue

DK BLU= Dark Blue

LT GRN= Light Green

DK GRN= Dark Green

Let me know if you require any further assistance.

Oct 20, 2010 | Oldsmobile Cutlass Cars & Trucks

2 Answers

I need to know which wires on the new pig tail wire in the the old harniss they are different colors but they both are marked a b c d so do i match colors or do i match a b c d can you tell me or show me...


Your best bet is to go to mitchelldiy online and get the wiring diagrams. Not knowing what year your car is and what harness or computer or component your talking about and since the wiring harness may not be the correct one for your application I would be hesitant to give advice that could ruin a computer if hooked up wrong.

Mar 22, 2010 | Cadillac STS Cars & Trucks

1 Answer

What are the color codes when wiring up a pigtail for hauling on a 02 town& country


RED=.BRAKE/BLACK = GROUND/YELLOW=TURN/GREEN=TURN/TAN=TAIL-LIGHTS&Side Marker lights/WHITE & BLUE if there can be for A.B.S. i.e. always have power supplied to them

Sep 13, 2009 | 2002 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...