Question about Fiat Cars & Trucks

Open Question

Remove diesel fuel injectors fiat 1.3 multijet

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 249 Answers

SOURCE: Trouble removing the engine cover from Fiat panda 2006 diesel

i guess you got a chip then, look at the cover ithink 3 or 4, circles, fine screw driver and pop em out to see the 10mm nuts.

Posted on Aug 15, 2009

  • 432 Answers

SOURCE: loss of clutch

Call the Fiat dealer and get the parts department. Tell them whats happening and ask if they offer a stronger plunger. If they dont, call a high performance auto parts store and ask if they have a racing clutch master cylinder. If they do, go look at it and see if its the same plastic plunger. It should be a heavy duty plunger.

Posted on Sep 03, 2009

  • 4 Answers

SOURCE: remove and install diesel fuel injector

First, keep everything as clean as possible. Contamination below 30 microns, which cannot be seen by humans, can destory a diesel fuel injection system. Clean everything off anything having to do with connections on the fuel system and cover any connections left open.

Begin by removing the intake manifold. This will remove the clips holding the injection lines passing underneath and around the intake runners. After removing the manifold, cover the openings in the cylinder head (I use wadded-up paper towels).

Next, remove the clips at the brackets on the injection lines closer to the injectors.

Loosen all of the injection connections at the injectors. Do not remove the lines.

You can remove the water crossover tube if it is in your way, but drain about a 1/2 gallon of coolant before your remove the crossover.

Remove the oil fill tube from the timing cover. Turn the engine clockwise, using a 15/16" socket and ratchet (or breaker bar) on the center bolt of the crankshaft. As you turn the engine over, a bolt will show up at the opening where the oil fill tube was removed. Remover the bolt and keep turning the engine over until you have removed all three bolts. Do NOT use the starter to turn the engine over and, after removing the third bolt, do NOT turn the crankshaft any more.

On top of the timing cover, behind the rounded top, is the place where the injection pump is bolted to the cover from the back side. Clean the top of the timing cover where it meets the injection pump and look for a thin line scribed into the cover and one on the injection pump. Note the position of the two lines (they are usually aligned) for reassembly.

Remove the throttle cable assembly from the injection pump. Remove all the wires from the pump and note which connection the big pink wire goes to. The other wires will be green. Remove the return hose at the top of the injection pump.

There are three nuts holding the injection pump to the timing cover and you will need a 15mm socket and/or wrench to remove them. When you do, the injection pump and injection lines can be removed as a unit. Note the position of the driveshaft of the injection pump to set the new one the same way. If you are not going to put things back together right away, cut up a plastic garbage bag and make covers for the injectors. Secure the covers with rubber bands or nylon cable ties to keep dirt out of the injectors.

Carefully transfer the injection lines to the new pump. It is possible to cross them up so pay close attention while moving the lines. Transfer the fuel inlet pipe to the new pump and whatever device is mounted on the passenger side of the old injection pump to the new pump.

Get a new injection pump to timing cover gasket and install it over the timing cover studs. Install the new injection pump after setting the driveshaft to match the holes in the gear inside the timing cover. The pump can only be installed one way since it is indexed to the gear. Reinstall the nuts on the studs and set the timing marks to the same position they were when you removed the old injection pump (the lines on top of the timing cover and the flange of the injection pump). Tighten the mounting nuts. Make sure that all the injection lines line up at their injectors, but do not tighten the connections at the injectors yet.

Put the first bolt back into the gear through the oil fill tube hole. Hand tighten it and then turn the crankshaft clockwise as before to install the remaining two bolts. Then, tighten all the bolts securely and resinstall the oil fill tube. Reinstall the throttle connections on the injection pump.

Install a new piece of 1/4" fuel line from the fuel filter to the injection pump (the old one is usuall brittle since it never gets changed). Remove the covers over the opening in the cylinders heads and reinstall the intake manifold using new gaskets.

Reinstall all the injection line clips that were removed and the coolant crossover tube (if you removed it and don't forget to add coolant to the radiator). Reconnect all the wiring on the injection pump, except for the big pink wire. Install a piece of clear tubing on the top of the injection pump and connect it to the return tee in front of it (where you removed the rubber hose from the old injection pump).

Now comes the fun part: Disconnect the glow plug relay connector (two small wires in a connector) from the middle of the relay. The relay is usually on the driver's fender and close to the battery.

Crank the engine, in short bursts, until you see fuel in the clear tubing on top of the injection pump. When you do, reconnect the big pink wire on the injection pump. Continue to crank the engine in short bursts (allowing the starter to rest between cranking cycles) until you see fuel dripping out of the injection lines at the injectors. When you do, tighten the connections where fuel is dripping. When all lines have been tightened, reconnect the glow plug relay connector. Remove the clear tubing on top of the injection pump and reinstall the fuel line that was removed from that location.

Then, try starting the engine normally. If it will not start, try some WD-40 down the intake. You can use ether, but you MUST disable the glow plugs be removing the connector at the relay.

The engine may run rough or stall at first but it should smooth out after all the remaining air comes out of the system.

Torque values are as follows:

Intake manifold: 25-37 ft-lbs
Gear bolts: 13-20 ft-lbs
Injection pump mounting nuts: 25-37 ft-lbs
Injection lines: 15-24 ft-lbs ("wrench tight" is fine)
Injection pump fuel inlet fitting: 15-20 ft-lbs

Posted on Feb 17, 2010

  • 608 Answers

SOURCE: fiat doblo 1.9 diesel year 2007. engine stop when low fuel tank

There is a possibility that your fuel transfer pump has quit and fuel is getting to your engine by gravity only. Have your tranfer pump flow rate tested. Also renew your primary fuel filter.

Posted on Mar 23, 2010

Testimonial: "i will check the fuel pump. i guess i will hear the pump start when i turn on the ignition. But - the engine also have stopped downhill(reg gravidity)"

HansPP
  • 2510 Answers

SOURCE: WILL NOT TURN OVER, TOTALLY

Are the battery terminals clean and are your battery leads not damaged in any way. Remove both battery cables and hold the terminals in boiling water for a while, make sure that there is no build-up of scale inside the terminals, then reinstall them, making sure that they seat properly and are tightened. (All your symptoms point to a weak battery or a poor connection).

Posted on Jan 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the transmission filler plug on my 2007 Fiat Bravo 1.9 multijet diesel with manual transmission? Is that a 10 mm bolt of about 50 mm long with a copper washer behind the head? Cheers.


filler plugs are normally located about 1/2 way up the side of the box
can be a hex plug around 19mm spanner size with a thread length of 12mm
It may even be a square head plug that is a bsp thread like what is used on water pipes
the fill plug hole is the oil level to the bottom of the threads in the hole

Jul 07, 2015 | Fiat Cars & Trucks

1 Answer

Fiat 500 1.3 multijet diesel with fault code p0089


P0089 Fuel pressure regulator - performance problem

Mar 30, 2015 | Fiat Cars & Trucks

1 Answer

My 1.9 diesel bravo has been in the garage for two weeks not starting in morning got they said fuel is congealing changed all filters still same problem


for diesel fuel to congeal it has to be poor quality with a high paraffin content close to 0 degrees c or contaminated. I would go for contaminated from a fungus growing in the fuel. Get a sample of the fuel from the tank and if it is a grey slimy mess then that will be the fungus. All diesels use a return line from the injectors that lubricates and cools the injectors.and this hot fuel creates a humid atmosphere in the tank so hat when the tank cools down the fungus grows in the condensed water. Try a wynns diesel fuel treatment product as it is pretty good at killing the fungus and cleaning the tank out.

Oct 29, 2014 | 2007 Fiat Bravo 1.9

1 Answer

Knock sensor replacement


wow triple posted and no year, no engine.. ouch. pick one.?
1.5 L M15A I4 petrol
1.6 L M16A I4 petrol
2.0 L J20A I4 petrol
2.0 L J20B I4 petrol
1.3 L Multijet I4 diesel
1.6 L DV6ATED4 I4 diesel
1.9 L Multijet I4 diesel
2.0 L Multijet I4 diesel its on the side of engine. near the cylinders. if at ALL.
post engine option
or go to alldata.com and look it up, with engine size.

why not post symtoms. ???

Jan 16, 2014 | Suzuki SX4 Cars & Trucks

2 Answers

I have a Diesel Fiat Punto 1.3 multi jet 2003. I cant start the car it keeps turning over and over and will not start. Ive had the pump and injectors checked, changed the starter motor, had new glow plugs....


First I would check to make sure you have the proper fuel pressure at the pump - you should have 2 pumps - one that delivers from the tank, and a high pressure pump for the injectors. Make sure that both are delivering properly - you may need to prime the pumps for quite some time if air got into the lines. Also make sure the cam / crank sensors wiring has no corrosion and is making proper contact. Between 0 to 300/400rpm the signal can be slightly erratic until the engine is started so I would not worry too much about that.

Mar 15, 2011 | 2006 Fiat X1/9

1 Answer

WILL NOT TURN OVER, TOTALLY DEAD. A FEW LIGHTS FLASHING ON INSTRUMENT PANEL, INTERIOR LIGHT WEAK. NO NOTHING. HAVE JUST INSTALLED NEW BATTERY WITH NO RESULTS. PLEASE ADVISE. FIAT PANDA DIESEL MULTIJET...


Are the battery terminals clean and are your battery leads not damaged in any way. Remove both battery cables and hold the terminals in boiling water for a while, make sure that there is no build-up of scale inside the terminals, then reinstall them, making sure that they seat properly and are tightened. (All your symptoms point to a weak battery or a poor connection).

Jan 30, 2011 | Fiat 124 Cars & Trucks

1 Answer

Fiat doblo 1.9 diesel year 2007. engine stop when low fuel tank


There is a possibility that your fuel transfer pump has quit and fuel is getting to your engine by gravity only. Have your tranfer pump flow rate tested. Also renew your primary fuel filter.

Mar 18, 2010 | 2007 Fiat X1/9

1 Answer

How to change air filter on fiat doblo 1.9 jtd


how to change a engine air filter on a Fiat emoction multijet 1.9 jtd

Sep 12, 2009 | 2006 Fiat X1/9

1 Answer

Loss of clutch


Call the Fiat dealer and get the parts department. Tell them whats happening and ask if they offer a stronger plunger. If they dont, call a high performance auto parts store and ask if they have a racing clutch master cylinder. If they do, go look at it and see if its the same plastic plunger. It should be a heavy duty plunger.

Sep 03, 2009 | 2006 Fiat 124

1 Answer

Trouble removing the engine cover from Fiat panda 2006 diesel


i guess you got a chip then, look at the cover ithink 3 or 4, circles, fine screw driver and pop em out to see the 10mm nuts.

Aug 15, 2009 | 2006 Fiat 124

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...