Question about Cars & Trucks

Open Question

Vw multivan electric rear sliding door not working

Electric doors disabled after battery restart

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: My 1999 pontiac montana rear sliding power door will not work

I went to bulldogsecurity.com and looked up the wiring diagram for this vehcle. However, prior to checking this part, I would check to see if you have a blown fuse. It doesn't hurt and only takes a few minutes. There should be a fuse for that either somewhere on the side of the dash or near the brake pedal area. If not it may be under the hood, but it should be inside the vehicle. You may have multiple fuse boxes. If it has (2) sliding doors it will have a wire for the auto doors in each kick panel (under the plastic trim/molding) when you open the door and look down you will see all of the trim/molding it should snap out or may be held in place with a screw or (2). Once you remove that you should see the wires. It says for the left side it is either light blue or black and the right side is definitely light blue. Trace this wire until you find out where it ends (the motor or switch to control the auto doors) Then test the switch/motor to see if it is bad.

Posted on Mar 02, 2009

Ad
  • 1 Answer

SOURCE: Power sliding door doesn't work!

Check out http://redhouseon7th.com/redhouse/howto/2001CaravanDoorRepair/index.html?page=Single&Language=0%22

Posted on Apr 06, 2009

morse008
  • 1111 Answers

SOURCE: VW Passat 1.6l 2000 (UK) Electrical failure

fuses are usually in the glove box or under the drivers dash or under the drivers side hood either physically inspect every fuse by pulling them one by one or the aid of a test light and a good ground to the test light

Posted on Sep 09, 2009

BRADLEYFRANC
  • 104 Answers

SOURCE: how do you reset electric windows on a 2003 vw

check the part no.to see if its the same as the old one.also might need to code it to the vehicle with a diagnostic machine

Posted on Oct 09, 2009

  • 12744 Answers

SOURCE: car door will not open. vw 1.8 1999 passat

remove door panel and check actuator for power and that actuator rod is connected and the plastic clip did not break or pop off

Posted on Nov 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vw multivan sliding door


UNLOCKED AND WONT OPEN?IF SO U NEED TO GET FROM THE BACK.TAKE OUT THE PANEL AT THE SLIDING DOOR AND CHECK FOR BROKEN OR TAKEN OUT GUIDES.IS IT ELECTRICALLY OPERATED?LET ME KNOW!!

Mar 06, 2014 | Volkswagen Cars & Trucks

1 Answer

The power side passenger door for a 2001 Chevy Venture van works every so often. The door doesn't move when the button is pressed on the panel in the headliner. The key remote doesn't work most of the time...


The proper way would be to look at a wiring diagram an test the electrical circuit's with a DVOM - digital volt ohm meter . Do you know how to test automotive electrical circuit's ?
Electric Testing Techniques You Need to Know
The Trainer 32 How To Read An Automotive Block Wiring Diagram
Free wiring diagrams here http://www.bbbind.com/free_tsb.html
Enter the vehicle info. year , make model and engine size . Under system click on body & accessories ,then under subsystem click on power sliding door . Click the search button then the blue link. Looking at the diagram you will see a control module is used .
Also reading factory service info. on how it works would be a good idea.

Rear Side Door Actuator Control Module
The rear side door actuator control module is capable of on-board diagnostic functions described in On-Board Diagnostic Features . The rear side door actuator control module monitors the door position at all times including during manual operation. After activating the on-board diagnostic modes, loosing battery voltage, or ground to the rear side door actuator control module the Power Sliding Door (PSD) Re-Initialization procedure must be performed in order for the rear side door actuator control module to correctly determine the door position.
Power Sliding Door System Description
The power sliding door system(s) can operate correctly only if the power sliding door is in proper mechanical condition. Any mechanical problems will affect the power sliding door operation and must be repaired before attempting to diagnose the power sliding door system. Manually open and close the power sliding door to determine if the door moves smoothly and without excessive resistance or binding. The power sliding door must also latch and unlatch without the use of excessive force. At any time during power sliding door open or close operation, excessive resistance to the door movement will cause the power sliding door to stop and reverse the direction of travel.
The power sliding door will operate only when the power sliding door on/off switch in the overhead console is in the on position. At anytime during power sliding door operation the on/off switch may be turned to the off position and the system will quit any function in process. The power sliding door will not open unless the transmission shift lever is in the park position and the door is unlocked. When the sliding door security lock is in the locked position the power sliding door will not open from the inside. The power sliding door close function will operate when the vehicle is in gear. The power sliding door module uses the VSS signal to determine if the vehicle is moving during a power sliding door close function. The momentum of the vehicle moving forward adds resistance to the door closing operation. When the rear side door actuator control module determines the vehicle is moving forward while closing the door, current flow through the actuator motor is increased instead of being reversed. The VSS signal circuit is supplied battery positive voltage through a resistor then monitored within the rear side door actuator control module. The VSS signal circuit is then pulsed to ground, or pulled low by the powertrain control module in relation to vehicle speed. The sliding door alarm will sound repeated short tones whenever the power sliding door system is turned on and the door is open while the transmission is out of park.
When the power sliding door system is on and manual operation of the power sliding door is detected the rear side door actuator control module activates the power assist feature. When the power assist is activated the power sliding door will continue to open or close without any further manual effort.
The power sliding doors may be operated using the Remote Keyless Entry System. The keyless entry transmitter will have one OPEN/CLOSE button with a van symbol on it for each power sliding door. The power sliding door ON/OFF switches in the overhead console must be in the ON position in order to operate the power sliding doors using the keyless entry transmitter. When a right hand power sliding door OPEN/CLOSE function is activated using a keyless entry transmitter the exterior lights will flash once indicating the RKE module has received the OPEN/CLOSE command. When activating a left hand power sliding door OPEN/CLOSE function with the keyless entry transmitter the exterior lights will not flash.

On-Board Diagnostic Features
The left and right power sliding door systems operate as independent systems. The on-board diagnostic modes are entered and operate the same in both systems.
The power sliding door systems are capable of the following on-board diagnostic functions:
• Diagnostic Mode 1: An audible signal indicates the diagnostic trouble codes stored by the rear side door actuator control module.
• Diagnostic Mode 2: An audible signal indicates when inputs to the rear side door actuator control module are active.
• Diagnostic Mode 3: Performs an output test of the sliding door unlatch actuator.
Entering On-Board Diagnostics
The on-board diagnostic modes can only be entered in a sequential order from modes 1-3.
• Enter the right power sliding door system on-board diagnostics using the right B-pillar open/close switch and the right on/off switch in the overhead console.
• Enter the left power sliding door system on-board diagnostics using the left B-pillar open/close switch and the left on/off switch in the overhead console.
1. Both power sliding doors must be closed and in the latched position.
2. Place the ignition switch in the OFF position.
3. Place the on/off switch in the overhead console to the OFF position.
4. Press and hold the B-pillar power sliding door open/close switch.
5. While holding the open/close switch, operate the on/off switch through 10 ON and OFF cycles within 10 seconds stopping in the on position.
6. The sliding door alarm will sound 1 long tone indicating diagnostic mode 1 is active.
Diagnostic Mode 1
Upon activating diagnostic mode 1, DTCs will begin to be signaled by the sliding door alarm. The DTCs are 2 digit codes and the codes are represented by the number of buzzes for each digit of the code number. For example a DTC 12 is represented with the following sequence: buzz, pause, buzz, buzz, long pause. Each DTC will be signaled 3 times before proceeding to the next DTC. Refer to Diagnostic Trouble Code (DTC) List . The DTCs will continue to be repeated in this manner until the on-board diagnostics are exited or mode 2 is entered. When exiting the on-board diagnostics all stored DTCs will be erased from the rear side door actuator control module memory.

Oct 13, 2017 | 2001 Chevrolet Venture

2 Answers

Door chime on 2007 chevy uplander will not stop even when the door is closed properly. Is there anyway to disable it without disabling radio


Had this problem for some time. I have had the dealer replace motor etc. Problem still returns. Noticed that the foam seal around the right side door has started flatening out over time and was beginning to spill into the lipped plate that the door sensor buttons possibly could be prevented from making proper contact. Trimmed approx. 3/8 of an inch off the foam in the area of the plate, and the problem seems to have gone away. Hope this helps.

Apr 25, 2010 | 2007 Chevrolet Uplander LT Minivan

1 Answer

Gaining access to my VW T4 westfalia multivan leisure battery?


Slide drivers seat forward, press small metal lever near seat track lower right rear to release seat and slide it foward off the track. Now, you should have full access to the leisure, secondary, battery.

Apr 19, 2010 | 1986 Volkswagen Wagon Camper

1 Answer

2001 Toyota Sienna r.h. sliding door ''rear latch switch'' location


To start, the noun "''rear latch switch'' is incorrect. It's actually called "Slide Door Lock". It's located on page BO-20 of the Toyota Repair Manual for the 2001 Sienna. There are two door locks on one sliding door. One in the front and one in the rear. Obviously, you want the one in the rear. The location for the "Slide Door Lock" (which also contains an electric switch) is in the rear of the sliding door located mid way up door. You can see (sliding door opened from the back) it without dissembling the door. And, the lock is made up of plastic (dirty white in color).

Mar 06, 2010 | 2001 Toyota Sienna

1 Answer

I have a 99 montana passenger side sliding door dont work. Hit either button all it does is clicks and motor seems to be fine.. I went to junk yard bought complete new motor and everything that comes...


I would check the overhead buttons there are two one opens the door, and the other beside it that shows the van crossed out, disables the electric sliding door feature. try playing with that, Also remember, that vehicle must be in PARK for the electric sliding door to open. Make sure the power lock on that door is working, and check the child safety lock when you have it open by the doors catch. Hope that Helps You.

Aug 02, 2009 | 1999 Pontiac Montana

2 Answers

2001 Oldsmobile Silhouette....Power lock on my power door doesn't come up completely and the door doesn't open with or without the button. What can I do? I also believe my van has other electrical issues...


From the back of the front door slide your hand in the sliding door crack and find the child-safety-lever. Push the lever up and/or down while moving the sliding door manual lock/unlock button to the up position. Also works on the non-powered sliding door.

Jul 15, 2009 | 2001 Oldsmobile Silhouette

1 Answer

Broken door handle - 2001 Nissan Quest SE


first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.

Trim Panel —Sliding Door Removal
  1. Remove the sliding door trim panel finish panel.
532ac84.gif 2. Remove the sliding door trim panel 2965fbe.gif Latch Remote Control —Sliding Door Removal
  1. Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. If equipped, disconnect the sliding door power door lock actuator electrical connector.
f373e91.gif
  1. NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
  2. Disconnect the sliding door rear latch cable.
  3. Remove the bolt.
  4. Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
  5. Disconnect the sliding door rear latch cable from the latch remote control.
b8f2f32.gif
  1. Remove the 4 sliding door front latch bolts.
NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.
  1. Remove the bolts.
  1. Remove the sliding door latch remote control.
cb5ee71.gif
Handle —Exterior, Sliding Door Removal
  1. Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .
  1. Remove the sliding door exterior handle.
    1. Remove the nuts.
    1. Remove the sliding door exterior handle.
0c820f3.gif

Mar 08, 2009 | 2001 Nissan Quest

1 Answer

Electric sliding door


pull the radio fuse under the hood in the relay/fuse center. this will clear the memory for the door. the fuse needs to be removed for 20 seconds

May 15, 2008 | 1996 Pontiac Trans Sport

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...