Question about Cars & Trucks

1 Answer

I have an 03 acura tl my headlight on the passenger side went out I checked fuses and the fuse was fine spent 100 for a new bulb replaced it and still didn't work and then on the same side my high beam goes out checked my fuse it was fine replaced bulb still didn't work any advice please

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 112 Answers

Check relay under the hood. also get a wire tester and check the wiring to theh eadlight and see if u have any juice going to it. if not then that is where your problem starts of tracing electric issue.

Posted on Jul 14, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 104 Answers

SOURCE: Right headlamp doesn't work on low beam only

in this case make sure you have voltage going to the low beam lights. 12 volts. you need a volt meter. if you do not have volatge you have to check and make sure power is going through the fuse. a bad fuse will be broke, but you can have a good fuse with no power going through it. if you have power going through the fuse you have a wiring open somewhere between fuse and whatever is between the headlight connecter.

plz check and get back i will keep checking on here on and off.

Michael
ASE certified
PLZ rate

Posted on Feb 09, 2009

bobjrdns
  • 84 Answers

SOURCE: 2002 acura tl headlight issue

MAKE SHURE YOUR GROUNDED AND THE BULB IS IN RIGHT SOME BULBS YOU CAN NOT TOUCH WITH YOUR FINGERS BECAUSE OF MISTURE ON SKIN

Posted on Oct 18, 2008

  • 1 Answer

SOURCE: 2002 Acura TL low beam headlight

How to Shift my headlight beam from position.
from I replace my headlight it's spatting directly on the ground..What can i do to change it from position

Posted on Feb 15, 2011

  • 4044 Answers

SOURCE: high beam headlights don't work, changed the bulbs, and checked the fuses, help

This is going to be a problem with your light switch or dimmer switch. Replace the light switch and see if that resolves the issue.

Posted on Nov 28, 2011

  • 1348 Answers

SOURCE: passengerside headlight highbeam not working

DAYTIME RUNNING LIGHT MODULES CAUSE A PROBLEM LIKE THAT

Posted on Mar 10, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change headlight bulb in 2003 Acura 3.2 CL


Nick, To see how headlight bulb is changed, check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Replacement How to replace install fix change hid head light ballast...
Headlight Change 1999 2003 Acura TL 1999 Acura TL 3 2L V6
Acura TL Headlight Replacement WITHOUT removing the bumper

Aug 06, 2016 | 2003 Acura 3.2CL

2 Answers

2005 Acura mdx passenger side headlight out, bulb ok, fuse ok, what next


Check for power and ground at the headlight plug. Test lights are cheap.

Oct 17, 2014 | 2005 Acura MDX

1 Answer

Acura T.L 3.2 2002, my left headlight stop coming on. Replace HID buld low beam. Didn't work right so I switch bulds right to left still only the left drivers side headlight won't come right on. Sometimes...


I having a same problem as you.
I have changed Head light (general head light 12V 37W)
I plug out inverter connector and connect 12V 37W bulb directly
It works fine.

Oct 26, 2010 | 2002 Acura 3.2TL

1 Answer

Both headlights went out same time . bulbs are good . fuses are good. back lights work and high beam works too. what else can it be? and is this common with these cars . 1998 acura 2.5 tl year is 1998 not...


Test the leads to the bulbs while the low beams are on and then when the brights are on. If you have good bulbs & fuses with no power on low, the problem is most likely the bright/dim switch.
Not exactly sure of the Acura layout, but the covers over the steering shaft should remove with several screws to allow access to the switch (usually the turn signals are also the bright/dim switch) Test the leads out to the headlights from the bright/dim switch, that will tell you if the switch is bad.
Airbags are closely involved with this removal/replacement, it is NOT recommended for a amatuer to undertake.

Dec 17, 2009 | 1998 Acura TL

2 Answers

2002 Acura TL Type-S Radio Fuse Blown??


Passenger Side fuse box, fuse number 9 neets to be replaced

Dec 09, 2009 | 2005 Acura TL

1 Answer

2002 Acura TL low beam headlight


How to Shift my headlight beam from position.
from I replace my headlight it's spatting directly on the ground..What can i do to change it from position

Mar 15, 2009 | 2002 Acura 3.2TL

2 Answers

Replacing HID headlight in 2004 Acura TL


HID Bulb Replacement

A transient high tension (25,000 V ) occurs at the bulb sockets of the high intensity discharge (HID) lamps when the combination light switch is turned ON, it may cause serious electrical shock or electrocution if you do not observe the cautions below.

CAUTION:
  • Never turn on the combination light switch before fitting the HID bulbs to their bulb sockets and completing the reassembly of the headlight assembly.
  • Do not service the headlights assembly in wet conditions, such as rain or snow, near a sprinkler system, or when your hands are wet to prevent electrocution.
  • Do not touch the surface of the HID bulbs with your bare hands and do not stain it with any oils and fats.
  • Do not disassemble the inverter unit and the ignitor unit.
  • Do not turn on the HID bulb by using a power source other than the battery mounted on your vehicle.
  1. Make sure you have the anti-theft codes for the radio and the navigation system, then write down the XM radio channel preset. Make sure the ignition switch is OFF.
  2. Turn the combination light switch OFF.
  3. Disconnect the battery negative cable, then disconnect the positive cable.
  4. Remove the headlight assembly.
37a2a12.jpg
  1. Remove the Torx bolt using a Torx T20 bit.
  2. Turn the cover (A) 45 ° counterclockwise to remove it from the headlight assembly.
71b91a6.jpg
  1. Turn the socket (A) 45 ° counterclockwise to remove it from the bulb (B).
  2. Pull the retaining spring (C) away from the bulb then remove the bulb.
  3. Make sure the bulb harness (D) is routed correctly so it does not contact the reflector (E).
  4. Install the new bulb in the reverse order of removal. Make sure the notches in the bulb align with the tabs in the headlight.
  5. After reconnecting the battery, enter the anti-theft codes for the radio and the navigation system, then enter the customer's XM radio channel presets.

Feb 13, 2009 | 2004 Acura TL

1 Answer

Right headlamp doesn't work on low beam only


in this case make sure you have voltage going to the low beam lights. 12 volts. you need a volt meter. if you do not have volatge you have to check and make sure power is going through the fuse. a bad fuse will be broke, but you can have a good fuse with no power going through it. if you have power going through the fuse you have a wiring open somewhere between fuse and whatever is between the headlight connecter.

plz check and get back i will keep checking on here on and off.

Michael
ASE certified
PLZ rate

Feb 09, 2009 | 2004 Acura TL

1 Answer

2002 acura tl headlight issue


MAKE SHURE YOUR GROUNDED AND THE BULB IS IN RIGHT SOME BULBS YOU CAN NOT TOUCH WITH YOUR FINGERS BECAUSE OF MISTURE ON SKIN

Oct 11, 2008 | 2004 Acura TL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...