Question about 1989 Honda Accord Sedan

1 Answer

Shift linkage diagram - 1989 Honda Accord Sedan

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

STICK or auto.
we cant see car, so.....

Posted on Feb 11, 2014

  • _-__-___-_
    _-__-___-_ Feb 11, 2014

    STICK or auto.

    we cant see car, so.....



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace the shift linkage in the pontiac montana van

On that van, like many other GM front-wheel-drive vehicles, the shift cable goes through a bracket on the transmission to the linkage( the little metal arm). Where the cable connects to the linkage, there is a ball stud. It takes quite a bit of force to disconnect the cable from that. If it became disconnected at that ball without any other outside influence, the shift cable may need to be replaced. You can try pushing the plastic end of the shift cable back on to that ball stud ,it should click into place.
If the ball stud became disconnected from the linkage(little metal arm), the linkage would need to be replaced.
There should be a locknut holding the linkage to the transmission stud right above the range selector switch. If it came loose of there, you may need a new linkage, and to replace that nut

Jun 09, 2014 | 2001 Pontiac Montana

1 Answer

Shift linkage diagram

Your linkage has come undone,climb under and reset.

Feb 02, 2014 | Nissan Cars & Trucks

1 Answer

Daewoo nubira shift linkage disconnected

Try looking on the Autozone web site for the info, or buy the repair manual.

Aug 08, 2012 | Daewoo Nubira Cars & Trucks

1 Answer

Shifting linkage lose and will not go into gear would like to see diagram of linkage were would i find one

I had the same problem on my 05 HUMMER. I got under truck and saw that the linkage bushing on shifter cable had come off the shifter. i put it back and was able to shift gears again. I moved the truck and it came off again. I had to get a eight dollare part from Advane Auto parts to fix problem

Jul 11, 2012 | 2003 Hummer H2

1 Answer

Change shift cable in 1997 explorer

start at the throttle linkage and disconnect there follow routing of old cable and place new one in same was old cable and finish at the transmission, suggest a chilton or hayes repair manual with diagrams and step directions, and helps with future repairs, auto stores around $30

Jun 09, 2012 | Ford Explorer Cars & Trucks

1 Answer

F150 broke shift tube

Look under the car the linkage on the trans may have come off.

Jul 18, 2009 | 1997 Ford F150 Regular Cab

1 Answer


Go to and register the vehicle (By VIN). Afterward you'lll have access to manuals, wiring diagrams, service bulletins, etc.
Good Luck.

Jun 02, 2009 | 2000 Hyundai Sonata

2 Answers

Need a diagram for the transmission linkage 1977 Delta 88

If your pan is dented or crushed your selector paw in the trans has nowhere to go, this is super easy to fix - dont try to fix the pan, you can get a new one for cheap - or a used one if the salvage yard has not crushed everything with that trans, go to the parts store and get a new one maybe $20-30, it is very straight forward - make sure you get a new gasket ((or)) what I do is use permatex rtv black and put a nice even bead around the pan - smooth it out with your finger to about 1/16" thick and let it set up for about 1/2 an hour or till a little tacky put all your bolts in finger tight and retorque aroun the pan every other bolt until they are all tight (check torque specs and definatly use a torque wrench) and might as well change the filter since you are there (very easy) use hurst hot shift fluid or B&M trick shift for replacement fluid

Jan 29, 2009 | 1985 Oldsmobile Delta 88

Not finding what you are looking for?
1989 Honda Accord Sedan Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides