Question about 2004 Nissan Maxima

1 Answer

Expansion Valve How do I replace the Expansion Valve in a 2004 Nissan Maxima?? Dealership wont let me know!!! Please and Thankyou

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 5,332 Answers

Follow the a/c lines to the firewall. The part they are attached to is the expansion valve. Once the a/c system is evacuated the lines can be removed from the expansion valve. The expansion valve can then be removed from the EVAP core.

Posted on Jul 14, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: HOW TO REMOVE THE REAR BRAKE LIGHT LENS TO REPLACE THE BULB

how do i remove my tail light assembly out of my 2005 nissan maxima

Posted on Mar 27, 2009

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

chromapr
  • 267 Answers

SOURCE: 2004 Nissan Maxima ABS light stays on, what do I

you need to run a scan to see what is wrong. it could be a wheel sensor or the abs pump. This is a realatively new vehicle and i would think something is blocking a wheel sensor from reporting info to the computer. some times things build up around the sensor and block it. or if there has been a recent accident one could be damaged and the shop didn't catch it. these parts really dont fail this quick look for something else. remove the wheels and look for a ring with a lot of teeth on the back side of the assembly. follow an electrical wire it will take you to the sensor which will be next to a ring with many teeth. The sensor recognizes the teeth moving and reports to the computer when they stop moving and that is when the abs starts pulsing the brakes for that wheel. if something gets in the way the sensor sees nothing and the light comes on. if this helps please reply cause that helps me keep answering here and good luck

Posted on May 02, 2010

ZJLimited
  • 17970 Answers

SOURCE: How to remove & replace

Nissan Car 350Z & Maxima 1999-06 - Removal & Installation

zjlimited_316.jpg

Fig. Removing power steering pump and exploded view of power steering pump

To remove power steering pump, refer to illustration.

zjlimited_317.jpg

Fig. Removing power steering pump and exploded view of power steering pump

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Drain power steering fluid.
  4. Loosen adjustment screw and power steering pump through bolt, then remove belt.
  5. Remove power steering pump union bolts and hose.
  6. Remove power steering pump bracket bolts.
  7. Remove power steering pump.
  8. To install, reverse removal procedure.
  9. Adjust belt tension.
  10. Bleed air from the system

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    Negative battery cable Engine cover Air cleaner box Water from radiator upper tank, them radiator upper hose Radiator fan shroud Loosen idler pulley, then remove belt
  3. Drain power steering fluid.
  4. Remove piping of high pressure and low pressure and the drain fluid from their piping.
  5. Remove bolt common to water pump and power steering pump.
  6. Remove bolt then remove power steering pump.

Hope helps.

Posted on Dec 27, 2010

Ironfist109
  • 3018 Answers

SOURCE: how to replace a camshaft sensor on 2004 nissan



Hi, this cars cam sensors are easy to change. One on the right side and one on the left side of the motor.

  • See my diagram for a visual


  1. Remove the mounting bolt.
  2. Remover the connector
  3. Remove the sensor
  4. Install new sensor.
  5. Reverse to complete.
  6. Same for the sensor on the other side.







ironfist109_99.png
ironfist109_350.jpg



  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Posted on Oct 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the expansion valve on a 1998 Nissan maxima


the expansion valve (TX) valve is on the inlet side of the evaporator under the dash (air conditioning)

Aug 05, 2015 | 1998 Nissan Maxima

Tip

How To Replace Vapor Canister Vent Valve Nissan Maxima 2004-08 1AAuto.com


How To Replace Vapor Canister Vent Valve Nissan Maxima 2004-08 1AAuto.com

on Mar 30, 2012 | 2004 Nissan Maxima

1 Answer

Where is the orifice located in a 2003 nissan maxima please Thank you


Don't have one

You have an expansion valve

You can't work on an A/C System yourself
anyway

Aug 30, 2013 | Nissan Cars & Trucks

1 Answer

2004 nissan maxima engine code p0021&p1135. Intake valve timing control solenoid has already been replaced. What else could cause this?


I think I answered this a couple of weeks ago on a different Nissan. Both codes are saying the computer can not control valve timing on bank two.
There is a solenoid that uses engine oil flow to adjust valve timing.
If the sensors and solenoid are good, the problem could be lack of oil reaching the solenoid, or a problem with the wiring harness.

Jul 11, 2012 | 2004 Nissan Maxima

1 Answer

I have a 2006 Nissan Maxima 3.5 SE. I believe the transmission is going out on it, had the transmission flued replaced, but the dealership does not want to listen to me and asked me to take it to another...


let me guess its a five speed automatic tha toperates perfectly when cold but the longer you drive and the hotter it gets the worse it performs?these unts have a very high notoriety for shift valves stiicking in valve body when hot.....slip shift shock on down shift and delayed ,harshengagement from rverse to drive etc.put a valve body in it as long as fluid is not black....brown is ok,and you will be good to go.please let me know how it comes out.

Feb 08, 2011 | 2006 Nissan Maxima

2 Answers

Have problems with a/c not cooling on nissan maxima 1999 year .has good pressures on gages .not cooling inside ,doors on box seem too be working .compressor is working .any ideas on what maybe wrong


You say the pressures are good?The low side on this vehicle need to be lower than most,because it has a expansion valve,it needs to be around 30 psi,to about 35,if it is not,and the freon level is correct,then the expansion valve is bad.If this was helpful,please rate,thank you.

Jun 15, 2010 | 1999 Nissan Maxima

1 Answer

Airconditioner compressor clutch bad.


It is usually with the AC core and heater core under the dash.

Apr 20, 2010 | 2000 Nissan Maxima

1 Answer

Drives but wont rev


Throtle air control valve faulty.Get a new valve fitted.

Aug 02, 2009 | 2001 Nissan Maxima

5 Answers

2004 nissan maxima


I have the same issue with my 2004 maxima.The service techs said it was the timing chain tensioners .Since they are hydaulic and they powered by the oil in the car .It is recommended to purge the the engine every time the noise starts to come back. I brought some an it really freaking work because I started to run it into a tree and go buy a toyota

Jun 18, 2008 | 2004 Nissan Maxima

Not finding what you are looking for?
2004 Nissan Maxima Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...