Question about Cars & Trucks

1 Answer

Oil pan remove from a 1949 ford v8?

Instructions for removing the oil pan from a1949 ford Tudor. Do I need to remove the engine?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

If the frame is not in the way you should be able to pull it in the car. if it is i would just raise the front of the motor up and pull it down.

Posted on Jul 13, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Psych0Thrash
  • 53 Answers

SOURCE: 2000 7.3 Liter diesel engine needing oil pan replacement

sadly I don't think there is. The oil pan is huge and sections of the frame are in the way of getting it in and out without damaging the pan severly. pulling that massive engine and replacing the pan, then putting the engine back in and reconnecting everything in 14 hours is a good estimate. sorry for the bad news

Posted on Aug 18, 2008

  • 72 Answers

SOURCE: How do I raise the 96 ford f150 truck to repair the oil pan

get a set of ramps to drive up on, or a bigger floor jack. ramps are the easiest.

Posted on Nov 27, 2008

  • 10 Answers

SOURCE: removal of oilpan

the engine needs to be supported from the top. your oil pan is most likely hanging up on the oil pump. to remove, the subframe must be lowered abit after you've supported the engine from the top.

Posted on Feb 07, 2009

  • 105 Answers

SOURCE: oil pan removal for 1994 k1500 4WD

You should be able to drop the front drive and pull the starter you should be able to drop the oil-pan without to much trouble

Posted on Mar 25, 2009

  • 834 Answers

SOURCE: removal procedure of oil pan for a 1997 chevy

To remove the engine oil pan either the engine has to be lifted all the way off of the motor mounts and the oil pan should just clear the flex-plate and transmission, or the front axle dropped down out of the way, or the transmission and flex-plate will have to be removed.

Usually if the engine can be lifted enough to fit a piece of 2x4 wood between the motor mounts and the frame then the oil pan will usually just have enough clearance to be removed from the rear and the oil pan should just clear the transmission and the flex-plate. Also, be sure to check that the fan blade does not damage the fan shroud when lifting the engine.

Let me know if you require any further assistance.

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions on how to remove oil oan 1998 explorer v8, thanks sherry


In order to replace the oil pan or oil pan gasket or any other part you must remove the engine from the truck, there is no removal possible without the engine out of the truck.

Apr 04, 2017 | 1998 Ford Explorer

1 Answer

How to replace oil pump on 1985 ford 3/4 ton truck with small v8 motor


your can either pull the engine to do it, or if you can get or have enough clearnce to drain the oil and remove the oil pan you can do it with the engine still in ,i have done it both way's , eaither way the pan has to come down or off to get to the oil pump. if you don't have enough room when leaving the engine in you can take the motor mount bolts out and use a block of wood and gently jack the engine up to get the room you need to pull the pan down and to get in there and do the work.

Dec 20, 2012 | Ford Cars & Trucks

1 Answer

97 mountaineer oil pan won't come out do you have to move exhaust


V6 or V8?

V6:
Section 303-01B: Basic Engine - 4.0L SOHC 1997 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Oil Pan
Removal
  1. Disconnect the battery ground cable.
    gj0146a.gif
  1. Raise and support the vehicle; refer to Section 100-02 .
  1. Remove the oil pan plug and drain the engine oil.
    ga2180a.gif
  1. Remove the ten oil pan bolts and remove the oil pan (6675).
    • Discard the gasket.
    ga1674a.gif

Installation
  1. NOTE: All sealing surfaces must be cleaned prior to assembly. Use metal surface cleaner F4AZ-19A536-RA or equivalent meeting Ford specification WSE-M5B392-A to clean the sealing surfaces.
    Position the oil pan and gasket and install the ten retaining bolts.
    ga1737a.gif
  1. Install the oil pan plug and refill the engine oil.
    • Use 5W30 engine oil meeting Ford specification WSS-M2C153-G.
    ga2190a.gif
  1. Lower vehicle.
  1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    Connect the battery ground cable.
    gj0147a.gif

Oct 05, 2011 | Cars & Trucks

1 Answer

How to do an oilpan on a 88 chevy montecarlo


  1. Disconnect battery negative cable.
  2. Remove air cleaner.
  3. Remove upper fail shroud (V8)
  4. Raise vehicle and drain oil pan.
  5. Disconnect A.I.R. hose at converter pipe (V8)
  6. Disconnect A.I.R. pipe at exhaust manifold (V8)
  7. Remove exhaust crossover pipe at manifold and converter.
  8. Remove starter.
  9. Remove flywheel cover.
  10. Disconnect transmission oil cooler lines at oil pan.
  11. Remove engine mount 'through' bolts on V8. Loosen right bolt and remove left on V6.
  12. Remove oil pan bolts and lower oil pan. Check that forward crankshaft throw and/or counter balance weight are not extending downward so to block oil pan removal. Turn crankshaft, necessary, to put throw on horizontal plane.
  13. Raise engine.
  14. Remove oil pan.
Installation


  1. Clean sealing surfaces on cylinder case and pan.
  2. Check oil pan gasket for damage; replace if necessary.
  3. Apply a small amount of 1052751 or equivalent to front and rear corners of oil pan.
NOTICE: Only a small amount of sealant is required. Excessive amounts of sealant may cause a problem with proper sealing of oil pan.


  1. Install retaining bolts and torque to 9 N.m (80 lb. in.).
  2. Raise engine, if necessary.
  3. Lower engine, install mount 'through' bolts and torque to 50 lb. ft. (65 N.m).
  4. Install torque converter cover.
  5. Install starter.
  6. Install exhaust crossover pipe at manifold and converter.
  7. Lower vehicle.
  8. Install fan shroud.
  9. Install air cleaner.
  10. Fill crankcase with oil.
  11. Connect battery negative cable, start engine and check for leaks.

Nov 30, 2010 | 1987 Chevrolet Monte Carlo

1 Answer

What is the proper procedure for removing the oil pan on 1976 ford f100 2wheel drive with a 360 v8


I believe their is enough room to slide the pan out if you loosen the motor mounts and jack the engine up.

Sep 13, 2010 | Ford F-100 Cars & Trucks

1 Answer

Need diagram for 2000 ford taurus oilpan


Oil Pan - Removal & Installation3.0L Engine
VIN S Engine
  1. Before servicing the vehicle.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Dual converter Y-pipe Transaxle support bracket Oil pan by following the bolt removal sequence shown

    8d11698.jpg
    Fig. Oil pan bolt removal sequence-2000-04 3.0L (VIN S) engine


    2272e92.jpg
    Fig. Oil pan bolt tightening sequence-2000-04 3.0L (VIN S) engine
Hope helps (remember rated and comment this).

Aug 15, 2010 | 2000 Ford Taurus

1 Answer

Where the oil pump in a 75 ford maverick is located and how to replace it!


Removal & Installation
  1. Remove the oil pan.
  2. Remove the oil pump inlet tube and screen assembly.
  3. Remove the oil pump attaching bolts. Lower the oil pump, gasket, and intermediate driveshaft from the crankcase.
  4. To install, prime the oil pump by filling either the inlet or outlet port with engine oil. Rotate the pump shaft to distribute the oil within the pump body.

5d9bd39.gif
6-cylinder oil pump disassembled


0777aa6.gif
V8 oil pump disassembled

  1. Position the intermediate driveshaft into the distributor socket. With the shaft firmly seated in the socket, the stop on the shaft should contact the roof of the crankcase. Remove the shaft and position the stop as necessary.
  2. Insert the intermediate driveshaft into the oil pump. Using a new gasket, install the pump and shaft as an assembly. Do not attempt to force the pump into position if it will not seat readily. If necessary, rotate the intermediate driveshaft hex into a new position so that it will mesh with the distributor shaft.
  3. Torque the oil pump attaching bolts to 10–15 ft. lbs. on the 6-cylinder engines, and 22–32 ft. lbs. on the 302 V8.
  4. Clean and install the inlet tube and screen assembly.
  5. Install the oil pan

Nov 19, 2009 | 1978 Ford Granada

2 Answers

I can't get my oil pan out from under the truck. Lack of room


Don't know what year or engine you have, but some of the ford v8 engines you have to remove motor mounts & block up... Think you have one of those. Hope this helps you, Rick

May 05, 2009 | Ford F-150 Cars & Trucks

1 Answer

Removing oil pan from 98 explorer V8 5.0


nniezgodzki: if you have a 2wd explorer, you need to remove the torsion bars to gain access to the oil pan based on the procedures shown in Alldata. The torsion bars are the rods which fit into the lower control arms and go towards the center of the truck frame. Removal and installation of the torsion bars has a procedure you need to follow, make sure you check into it and follow it. if you need help, write me and i'll do my best to help you.

Apr 10, 2009 | 1998 Ford Explorer

1 Answer

Trying to drop the oil pan out of my 1994 Ford F-150 (4.9L) to replace the gasket. Ive taken out the motor mounts and jacked the engine almost high enough to get the oil pan out and I am wondering if i...


done this on several i-6 f-150s. slide back or remove transmission, remove motor mount bolts from frame(not motor), jack motor up as far as possible without damaging egr valve or wiper motor when they hit, shim under motor mounts so that when you drop the jack the motor does not come back down any(the motor is well balanced on the mounts, it will not fall out of the truck like a v8 will), then remove the oil pan. you May have to remove the pickup tube(usually not), and you May have to rotate the crankshaft so that the lobes clear the oil pan. this is a common problem with these trucks due to the size of the oil pan(Huge), and the minimum pan to crossmember clearance

Jul 19, 2008 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...