Question about 1999 Ford Taurus

1 Answer

390 MOTOR where dose the fuel pump mount on the motor?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Ford Master
  • 21,873 Answers

Should be on the driver side of the timing cover.

Posted on Jul 13, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why dose my fuel pump fues keep blowing

check the wiring from the fuse to the pump for broken insulation that is earthing out the wire and causing a dead short. Check for screws .pinched wires under mounts, melted wires on exhaust, shorting out in connections.

Sep 01, 2014 | Cars & Trucks

1 Answer

Rough idle and bucks while driving

1 Open the hood. Locate the fuel pump, mounted to the driver's side of the engine block, approximately midway between the front and rear of the motor.2 Loosen the fuel-line retention nuts on the pump with a tubing wrench turned in a counterclockwise direction. Carefully pull the fuel-inlet line and the outlet line from the fuel pump, being careful not to bend the metal lines. Have a rag handy for any fuel spills when removing the lines.3 Loosen and remove the two fuel-pump retaining bolts with a socket and ratchet. Place the bolts aside for installation of the replacement fuel pump.
Pull the pump straight out of the engine block and remove it from the engine bay. Scrape any gasket reside from the mounting surface of the engine block with a gasket scraper.
Place a new gasket over the mounting surface of the replacement fuel pump and hold it to the mounting surface on the engine block, lining up the mounting holes. Thread the original retaining bolts through the pump and into the engine block and tighten them.
Reconnect the fuel lines to the pump and tighten the fittings with a tubing wrench. Close the hood.

Nov 18, 2011 | 2004 Jeep Grand Cherokee

2 Answers

I need a manual for a 83-84 ford f150 pick up, as i need to posibbly replace the fuel pump , where can i d/l a free manual ?

Ford Pick-Ups/Bronco 1976-1986 Repair Guide
Electric Fuel Pump - Removal & Installation

Two electric pumps are used on fuel injected models; a low pressure boost pump mounted in the fuel tank and a high pressure pump mounted on the vehicle frame. Some models equipped with the 8-460 (7.5L) carbureted engines use a single low pressure pump mounted in the fuel tank.On injected models the low pressure pump is used to provide pressurized fuel to the inlet of the high pressure pump and helps prevent noise and heating problems. The externally mounted high pressure pump is capable of supplying 15.9 gallons of fuel an hour. System pressure is controlled by a pressure regulator mounted on the engine.
With internal fuel tank mounted pumps tank removal is required when servicing the pump. Frame mounted models can be accessed from under the vehicle. Prior to servicing release system pressure (see Fuel Supply Manifold details). Disconnect the negative battery cable prior to pump removal.

More details can find in (free register); select the year, make, model and engine.

I hope help you with this (remember rated this help) Good luck.

Oct 16, 2009 | 1983 Ford F150

1 Answer

How do I replace a 93" oldsmobile cutlass fuel pump dose anyone know where i could get a free guide with pics is pos.

Removal & Installation

Exploded view of the fuel sender, including the fuel pump

Click to Enlarge
  1. Properly relieve the fuel system pressure

  1. If not already done, disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Safely drain and remove the fuel tank assembly as outlined later in this section.
  4. Detach the quick-connects from the fuel sender assembly and remove the fuel lines.
  5. Using tool J 35731, or an equivalent spanner wrench, remove the fuel sender lockring.
  6. Lift the sender assembly carefully out of the fuel tank.
  7. Remove the sender O-ring from the top of the sender and discard.

WARNING Do NOT run the fuel pump unless it is submerged in fuel. Running the pump dry will cause serious damage to the fuel pump and may cause the pump to explode due to the oxygen in the air.

  1. Note the position of the fuel pump strainer on the fuel pump and, while supporting the pump assembly in one hand, twist the strainer off the pump and discard the strainer.
  2. Detach the fuel pump electrical connector.
  3. Remove the clamp from the fuel line at the top of the pump.
  4. Hold the fuel sender upside down on a work bench and pull the fuel pump out of the lower mounting bracket. Once the pump is clear of the lower mounting bracket, tilt the pump outward and disconnect the pump from the sender assembly.
To install:
  1. Replace any attaching hoses or rubber sound insulators that show signs of deterioration.
  2. Install the rubber bumper and insulator on the fuel pump.
  3. Hold the fuel sender upside down and install the fuel pump between the fuel pulse dampener and mounting bracket.
  4. Attach the fuel pump electrical connector.
  5. Install the retaining clamp on the fuel line.
  6. Install a new fuel pump strainer on the outer edge of the ferrule until fully seated. The strainer must be facing the same direction as it was before removal.
  7. Position a new O-ring on the top of the fuel tank and install the sender assembly.
  8. Install the lockring using J-35731, or an equivalent spanner wrench.
  9. Install the fuel tank as outlined later in this section.
  10. Refill the gas tank.
  11. Connect the negative battery cable.
  12. Turn the ignition switch to the ON position to pressurize the fuel system and check for leaks.

Oct 11, 2009 | 1992 Oldsmobile Cutlass Supreme

1 Answer

No fuel presure pump dose not run

start by checking the fuel pump fuse and relay if both those are good look to see if you have got power to the pump if yes you may need a new pump

May 17, 2009 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1999 Ford Taurus Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides