Question about Ford Cars & Trucks

1 Answer

1978 FORD PICK UP 390 MOTOR where dose it mount on the motor?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 21,873 Answers

On the driver side of the timing cover.

Posted on Jul 13, 2013

Testimonial: "thank every one . when i looked all i seen was timing chane do not know what runs it "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i find out what year my ford 2300 was made


The Model Design digit is the 3rd digit in the part number. It identifies the intended model for the part.It consists of mostly a letter but with some car models a number replaces the letter.
Most parts are designed for more then one model application. They are generic Model Design digits like A O or S. These generic digits make the part universal and/or specific to a body type.
Take this example, C8OE-9510-D is a 1968 Carburetor designed for 390 motor with Fairlane body type. But this was not designed exclusively for the Fairlane application alone as the carburetor was also used on Mustangs 390 and Cougars 390.

Oct 23, 2016 | Ford Cars & Trucks

1 Answer

Ok I have a 1995 ford aspire im trying to figure out how to replace the oil pump


Disconnect the motor mounts and jack the engine to remove the oil pan. Remove the oil pan, replace the oil pump you'll find at the end of a pick up tube, replace the pump and put the pick up tube back on the new pump making sure it's in the same low position it was when removed, replace the oil pan gasket and put the oil pan back on, lower the engine and put the motor mount bolts back in. Put in the proper amount of oil and go.

Nov 13, 2014 | 1995 Ford Aspire

1 Answer

390 MOTOR where dose the fuel pump mount on the motor?


Should be on the driver side of the timing cover.

Jul 13, 2013 | 1999 Ford Taurus

1 Answer

1978 FORD PICK UP 390 MOTOR


Do you have a question ?

Jul 13, 2013 | Cars & Trucks

1 Answer

97 FORD EXPEDITION,DOSE ANYONE KNOW OF A BETTER WAY TO PUT IN HEATER BLOWER MOTOR,THAN PUTTING A SMALL CUT IN FIRE WALL??THANKS BILL,ANC,AK


From the manual courtesy of Justanswer.com
Motor, Blower
Removal
  1. If equipped, remove the aftermarket air filter.
  1. If equipped, remove the mounting bracket for the removed cover.
  1. Disconnect the christmas tree retainer from the motor mounting plate.
  1. Disconnect the motor electrical connector.
  1. Remove the blower motor cover.
    1. Remove the three screws.
    1. Pry to release the three tabs.
    1. Remove the cover.
  1. CAUTION: Carefully remove the blower motor so as not to damage the wheel.
    Remove the blower motor.
    1. Remove the three screws.
    1. Remove the blower motor.
  1. Remove the wheel from the blower motor.
    1. Remove the push clip.
    1. Remove the wheel.
  1. Remove the gasket.

Installation
  1. To install, reverse the removal procedure.

Jan 26, 2012 | Ford Expedition Cars & Trucks

1 Answer

390 ford engine will not idle when in gear. how do i tell if it has burnt valves 1976 ford pick up f100 automatic


you need to do a compression test and a leakdown test. Both take special tools and you will need an air compressor for the leakdown tool.

Feb 21, 2010 | Ford F-100 Cars & Trucks

1 Answer

Torque settings for 390 v8 heads


the ford fe motor 390 heads should be torque to 90 foot pounds

Nov 11, 2009 | Ford Thunderbird Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...