Question about 2002 Mazda MPV

1 Answer

Ignition lock cylinder

How do i replace ignition switch

Posted by on

  • Anthony DiLugi Jul 16, 2013

    Dennis, I cant turn key from locked position, any ideas

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 76,164 Answers

The steering column is covered by two plastic trim pieces, on the bottom one remove the screws and the covers will come off, then the switch can be easily re[laced. Alwa7ys diarm the airbag system before doing any work, it can seriously injure you if it goes off accidently.

Posted on Jul 13, 2013

  • Anthony DiLugi Jul 16, 2013

    Can it be the cylinder and not whole switch or could it be the key in ref to anti-theft chip

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Relay switch


Ignition and Start Switch Replacement
Removal Procedure
2c23f8d.jpg Disconnect the battery ground cable. .
Remove the steering column filler panel.
Remove the knee bolster bracket.
Remove the instrument panel (I/P) cluster trim panel.
Remove the ignition switch bolts.
Lower the ignition switch away from the instrument carrier.
Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
Depress the transaxle park/lock cable retainer to release. Pull to remove the park/lock cable from the ignition switch.
Important: The Passlock? electrical connector cannot be removed until the lock cylinder is removed.

Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
d857e46.jpg Disconnect the Passlock? electrical connector.
Disconnect the electrical connectors.
4093e3a.jpg Important: Ignition switch lock cylinder that won't rotate or is seized.

Perform the following procedure if the ignition switch lock cylinder is seized or won't rotate.
12.1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2. Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch reward (toward the key entry end) from the cylinder release button.

12.3. Carefully drill a hole through the plastic housing with a 1/8 inch drill bit.

12.4. Carefully drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 9/32 inch drill bit.

12.5. Remove portions of the broken spring from the hole using a small suitable tool.

12.6. Grasp the ignition switch lock cylinder and remove it from the switch housing.

12.7. Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8. Follow service manual procedures when cylinder cording is required. Refer to Key and Lock Cylinder Coding in General Information.

Installation Procedure
If the lock cylinder would not rotate or was seized, perform the following procedure:
1.1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.

1.2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.

1.3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing.
9600af8.jpg Connect the electrical connectors.
Connect the Passlock? electrical connector.
Connect the park/lock cable to the ignition switchdd765ba.jpg Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
Remove the key
681874a.jpg Position the ignition switch to the instrument carrier.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the ignition switch bolts.
Tighten

Tighten the bolts to 10 N?m (89 lb in).

Install the trim plate bezel to the I/P cluster. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Install the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Install the steering column filler panel. Refer to Steering Column Filler Replacement .
Connect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.

Dec 05, 2013 | 2005 Chevrolet Impala

1 Answer

Need to replace ignition cylinder. no keys


This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal
  1. Remove the steering wheel (3600). Refer to the procedure in this section.
  1. Remove the four lower steering column shroud screws.


    j5021c.gif

  1. Separate the upper and lower steering column shrouds.
  1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
  1. Remove the upper and lower steering column shrouds.
  1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
  1. If equipped, remove the ignition/shifter interlock cable screw.
  1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
  1. Use a chisel to remove the two ignition switch lock cylinder bolts.
  1. Remove the ignition switch lock cylinder from the steering column.
  1. Disconnect the ignition key reminder switch electrical connector.
  1. If necessary, remove the ignition key reminder switch.


    j5028b.gif

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

Mar 25, 2011 | 1997 Ford Probe

1 Answer

How do i replace a ignition switch for a 1992 mercury sable


The ignition switch on Mercury Sable is integrated into the ignition cylinder. When this switch fails, you may need to purchase a special switch from a Ford dealership if the switch used a wireless transponder.


Instructions for NON Functional Cylinder (Cylinder will Not Turn or No Keys ):
1. Disconnect the negative battery cable.
2. Remove the steering wheel.
3. Using locking pliers, twist the cylinder cap until it separates from the lock cylinder.
4. Using a 3/8 in. (10mm) diameter drill bit, drill down the middle of the ignition lock key slot approximately 13/4 in. (44mm) until the lock cylinder releases from its breakaway base. Remove the lock cylinder and drill shavings from the lock cylinder housing.
5. Remove the retainer, washer, ignition switch and actuator. Thoroughly clean all drill shavings and other foreign materials from the casting.
6. Inspect the lock cylinder housing for damage from the removal operation. If the housing is damaged, it must be replaced.

To install:
1. Replace the lock cylinder housing, if damaged.
2. Install the actuator and ignition switch.
3. Install the trim and electrical parts.
4. Install the ignition lock cylinder.
5. Install the steering wheel.
6. Connect the negative battery cable, then check the lock cylinder operation.


Instructions for Functional Cylinder ( Cylinder will Turn with Key):
1. Disconnect the negative battery cable.
2. Turn the lock cylinder key to the RUN position.
3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

To install:
1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
3. Connect the negative battery cable.


Door Lock:
When a lock cylinder must be replaced, replace both sides as a set to avoid carrying an extra set of keys.
1. Remove the door trim panel and watershield.
2. Remove the clip attaching the lock cylinder rod to the lock cylinder.
3. Pry the lock cylinder out of the slot in the door.


To install:
1. Work the lock cylinder assembly into the outer door panel.
2. Install the cylinder retainer into the slot and push the retainer onto the lock cylinder.
3. Connect the lock cylinder rod to the lock cylinder and install the clip. Lock and unlock the door to check for proper operation.
4. Install the watershield and door trim panel


Hope this helps.

Feb 15, 2011 | 1992 Mercury Sable

1 Answer

How do you replace the ignition key switch for a '96 chevy diesel 1 ton 4wd pickup truck?


Ignition Switch Removal & Installation To Remove:
  1. Remove the steering column trim covers.
  2. Remove the wire harness from the retainers as needed.
  3. Slide the 2 connectors of the multifunction switch assembly out from the bulk head connector.
  4. Detach the key alarm connector from the lock assembly.
  5. Remove the ignition switch mounting screws and the ignition switch from the steering column.
Ignition switch removal/installation gm-08-00-1141.gif

To Install:
  1. Install the ignition switch on the lock module.
    • Tighten the screws to 42 lb in (4.7 Nm).
  2. Install the key alarm connector on the lock module.
  3. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
  4. Install the harness in the original retainers.
  5. Install the steering column trim covers.
---
Ignition Lock Cylinder Removal & Installation To Remove:
  1. Disconnect the negative cable from the battery.
  2. Disable the supplemental inflatable restraint (SIR) system.
  3. Remove the steering column trim covers.
  4. Turn the ignition lock cylinder to the run position.
  5. Using an awl with a bent tip, insert the tip into the access hole of the ignition lock cylinder.
  6. Turn the lock cylinder to start and push down and hold the lock cylinder retaining pin.
  7. Release the lock cylinder to the run position and withdraw the cylinder from the steering column.
Ignition lock cylinder removal gm-08-00-1139.gif

To Install:
  1. Align the slot in the steering column to the tab on the lock cylinder and install the lock cylinder until it locks in place.
  2. Install the steering column trim covers
  3. Connect the negative cable to the battery
  4. Check for correct operation
prev.gif next.gif

Oct 08, 2010 | Chevrolet 3500 Cars & Trucks

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

2 Answers

Car still running after take key out . cheked barrel thats ok don't know if it's relay problem


I think you have a bad ignition switch, not the ignition lock cylinder. they are 2 different things.

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.

Nov 21, 2009 | 1996 Ford Taurus

1 Answer

My key will start the car but it wont turn the car off i have to unplulg the distributor to kill theh car. Also the ignition switch in the car rotates all the way around but it has always done that it just...


the ignition switch is an electrical part. The lock cylinder is whre the key goes and it activates the ignition switch. If you pulled the lock cylinder out, you could operate the car with a screwdriver.
Either you have damaged the ignition switch where the lock cylinder goes into it, or the lock cylinder is damaged where it fits into the ignition switch.

this is 96 taurus, don't have 92 sorry

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.
------------------
Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Ignition Switch The ignition switch (11572), which is mounted on the steering actuator housing (3F723), operates in the following manner:
  • The ignition switch is cycled through rotation of the ignition switch lock cylinder (11582) through a pin which is part of the ignition switch.
  • The ignition switch lock cylinder also controls the mechanism which provides a positive lock for the transaxle linkage and the steering system.
  • The locking mechanism is located in the steering column housing.
The ignition switch lock cylinder positions are:
  • ACC
  • LOCK
  • OFF
  • RUN
  • START
The key can be removed from the ignition switch lock cylinder with the column-shift transaxle only when the shift lever is in PARK position and the key is in LOCK position.
  • The ACC position operates while the steering and transaxle remain locked.
  • The engine shuts off when the key is turned to the OFF position without locking the steering or transaxle.
Blade Type
The ignition switch has blade-type terminals that engage with one multiple connector. The multiple connector is secured to the ignition switch by an integral connector fastener.

May 05, 2009 | 1992 Mercury Sable

1 Answer

New Ignition Cylinder doesnt click in?


Lock Cylinder Functional
Removal
  1. NOTE: The following procedure applies to vehicles that have functional ignition switch lock cylinders (11582), lock cylinder keys are available for these vehicles or the lock cylinder key numbers are known and the proper key can be made.

    Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Turn ignition switch lock cylinder to RUN position.
  1. Place a 3.17 mm (1/8-inch) diameter wire pin or small drift punch in hole in lower steering column shroud (3530) under ignition switch (11572). Press retaining pin while pulling out on ignition switch lock cylinder to remove it from steering column lock cylinder housing (3511).
Installation
  1. Install ignition switch lock cylinder by turning it to RUN position. Insert ignition switch lock cylinder into steering column lock cylinder housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning ignition switch lock cylinder to OFF position. This will permit cylinder retaining pin to extend into steering column tube flange hole.
  1. Rotate ignition switch lock cylinder, using lock cylinder key, to ensure correct mechanical operation in all positions.
  1. Connect battery ground cable.

Apr 03, 2009 | 1995 Ford Taurus

2 Answers

96 ford windstar ignition probs


the ignition switch is the electrical part behind the lock cylinder where the key goes in.

Ignition Switch Lock Cylinder
Lock Cylinder Functional
Removal
  1. The following procedure applies to vehicles that have a functional ignition switch lock cylinder (11582) and keys. If the key numbers are known, the correct key can be made. Disconnect the battery ground cable (14301). For additional information, refer to Section 14-01 .
  1. Turn the ignition switch lock cylinder to the RUN position.
  1. Place a 3.17-mm (1/8-inch) diameter wire pin or small drift punch in the hole in the steering column shroud under the ignition switch lock cylinder. Depress the retaining pin while pulling out on the ignition switch lock cylinder to remove it from the housing of the steering column.
Installation
  1. Install the ignition switch lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the ignition switch lock cylinder into the steering column housing. Make sure the ignition switch lock cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the retaining pin of the ignition switch lock cylinder to extend into the hole of the steering column.
  1. Using the key, rotate the ignition switch lock cylinder to make sure of correct mechanical operation in all positions.
  1. Connect the battery ground cable.
-------------------------------------------------------------------------------------
Ignition Switch Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the upper steering column shroud (3530) by removing the four or five self-tapping screws. Remove key release lever (3F527) (if equipped).
  1. Remove lower steering column shroud.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.


71f4c5f.gif


Item Part Number Description 1 11572 Ignition Switch 2 — Ignition Switch Lock Cylinder Housing 3 — Slot in Lock/Column Assembly A — (Part of 11572) Pin B — Alignment Mark
Installation
NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

  1. Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Check to make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install upper steering column shroud.
  1. Install the lower steering column shroud and key release lever (if equipped).

Feb 27, 2009 | 1996 Ford Windstar

3 Answers

2005 chevy impala ignition switch


Ignition and Start Switch Replacement
Removal Procedure
2c23f8d.jpg Disconnect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.
Remove the steering column filler panel. Refer to Steering Column Filler Replacement .
Remove the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Remove the instrument panel (I/P) cluster trim panel. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Remove the ignition switch bolts.
Lower the ignition switch away from the instrument carrier.
Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
Depress the transaxle park/lock cable retainer to release. Pull to remove the park/lock cable from the ignition switch.
Important: The Passlock? electrical connector cannot be removed until the lock cylinder is removed.

Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
d857e46.jpg Disconnect the Passlock? electrical connector.
Disconnect the electrical connectors.
4093e3a.jpg Important: Ignition switch lock cylinder that won't rotate or is seized.

Perform the following procedure if the ignition switch lock cylinder is seized or won't rotate.
12.1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2. Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch reward (toward the key entry end) from the cylinder release button.

12.3. Carefully drill a pilot hole through the plastic housing with a 1/8 inch drill bit.

12.4. Carefully drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 9/32 inch drill bit.

12.5. Remove portions of the broken spring from the hole using a small suitable tool.

12.6. Grasp the ignition switch lock cylinder and remove it from the switch housing.

12.7. Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8. Follow service manual procedures when cylinder cording is required. Refer to Key and Lock Cylinder Coding in General Information.

Installation Procedure
If the lock cylinder would not rotate or was seized, perform the following procedure:
1.1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.

1.2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.

1.3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing.
9600af8.jpg Connect the electrical connectors.
Connect the Passlock? electrical connector.
Connect the park/lock cable to the ignition switchdd765ba.jpg Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
Remove the key
681874a.jpg Position the ignition switch to the instrument carrier.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the ignition switch bolts.
Tighten

Tighten the bolts to 10 N?m (89 lb in).

Install the trim plate bezel to the I/P cluster. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Install the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Install the steering column filler panel. Refer to Steering Column Filler Replacement .
Connect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.

rate me fix ya cuz this is the fix 100%

Aug 17, 2008 | 2005 Chevrolet Impala

Not finding what you are looking for?
2002 Mazda MPV Logo

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...