Question about Cars & Trucks

1 Answer

Hi i have 2004 1.6 ford bantam rocam that wont start, all the dashboard light come on but thats it! Checked all the normal suspects, new starter, battery all fuses check and replaced the crank angle sensor! Tested the key code to and working fine!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 78 Answers

Firstly,check that the car has spark and petrol,from there you can be assured that it is a electrical problem

Posted on Jul 13, 2013

  • Jaco Roets Jul 14, 2013

    Did check it but still dead, electrical but where do i start? The pcm?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
csmock132
  • 4669 Answers

SOURCE: my 2004 ford taurus wont start i checked the

Is the security light flashing with the key in the run position?

Posted on Mar 28, 2010

  • 79 Answers

SOURCE: no power to starter 2004 chevy tahoe

Hi
It could be your neutral safety switch. It could be the starter relay which is located in the fuse panel box. It could be the smaller wire going to the starter could be loose or corroded.

Posted on Apr 01, 2009

MNfisherman
  • 11896 Answers

SOURCE: ford f150 1988 4.9 cranks but doesnt start

If you are getting fuel and spark, than it probably is either a bad ground, or the TPS sensor itself.

Posted on Jun 22, 2009

  • 141 Answers

SOURCE: 90 Subaru Legacy with no spark

Have you checked the ignition fuses, or checked for power to your ignition module? You have everything else covered! I hope these ideas will get you running. Best wishes.

Posted on Jan 20, 2009

tayjoejoe
  • 2215 Answers

SOURCE: 1996 ParkAvenue Buick want crank turn the key

GM cars are notorious for faulty anti theft security systems. When these fail, the car thinks its being stolen and shuts down the starter. Most noticeable symptoms are the car not starting, everything else still working, and a light illuminated on the dash that says "security". If you see this light when it doesn't start, then this is 100% your problem. Go to this link for info and ways to fix it yourself for cheaper. http://vatspasslockpasskeysecurityhelp.yolasite.com/

Posted on Aug 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the speed sensor situated on a Ford Bantam 1.6 rocam


It is plugged into the transmission where the speedo cable would go in older cars.

Jun 22, 2016 | 2008 Ford Bantam 1.6i

2 Answers

How do I fix a Bantam that wont start?


no idea but change the mass air flow sensor on or in the inlet manifold

Jan 03, 2016 | 2005 Ford Bantam 1.3i

1 Answer

Why is my ford bantam 1.3 cranking but not starting?


probably the immobilizer has been activated
check fob key battery
reset the immobilizer using a scan tool on the ECM

Oct 09, 2015 | Ford Cars & Trucks

1 Answer

Ford bantam does not start


Check the reset switch near yo icu. reset it if off

Mar 16, 2013 | 2005 Ford Bantam 1.3i

2 Answers

Guys I've got a problem with a ford bantam 1.6i 2003 model rocam engine, its overheating even though the cylinder head was skim but it still overheating. please assist!


Check what head gasket was used . I suspect that an after market gasket was used. If that is the case there will be holes in the block and head thet have no matching holes in the gasket thereby causing the problem

Jan 07, 2013 | 2006 Ford Bantam 1.6i

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

896 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...