Question about Cars & Trucks

Open Question

Cylinder head bolt torque in a 1995 nissan maxima v6

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

Ad
joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder head torque and sequence


try this link then find motor size and year
note nissan rec. replacement oflbuyhk head bolts
http://olybrake.com/pdf/fel_pro_torque_specs_guide.pdf

Nov 07, 2015 | 1992 Nissan Maxima

1 Answer

What are the torque specs on a 2000 Nissan maxima head


14179124-0r3idicjw2hp5z0o4sqjrbpc-4-0_0.gif


14179124-0r3idicjw2hp5z0o4sqjrbpc-4-1.gif
NOTE
If possible, replacement of the head bolts is suggested.
  1. If replacement of the head bolts is not possible, perform the following bolt measurement:
    1. Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    2. Measure the diameter of the head bolt 1.89 in. (48mm) from the bottom of the bolt.
    3. Whenever the size difference between the 2 measurements exceeds 0.0043 in. (0.11mm) the head bolts must be replaced.
  2. Install the cylinder head bolts and torque in sequence as follows:
    1. Step 1: 72 ft. lbs. (98 Nm).
    2. Step 2: Completely loosen all bolts.
    3. Step 3: 25-33 ft. lbs. (34-44 Nm).
    4. Step 4: plus 90-95 degrees clockwise.
    5. Step 5: plus 90-95 degrees clockwise.

Aug 30, 2012 | Cars & Trucks

1 Answer

2002nissan3.5cylinderheadtorque



2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Apr 12, 2012 | Cars & Trucks

2 Answers

2002 nissan maxima 3.5 cylinder head torque


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 17, 2012 | Nissan Cars & Trucks

1 Answer

Torque setting head 2002 nissan maxima


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 17, 2012 | Nissan Maxima Cars & Trucks

1 Answer

Hello, Where is the Cam position sensor located on a 2004 Nissan maxima bank 1 located?


3.5litre V6 Front wheel drive, the cam position sensor is in the back of the cylinder head above the transmission. bank one is the front bank, nearest to the grill. the cam sensor is held into the head with a 10mm bolt, has one wireing connector with 3 wires in it. the sensor is sort of round with a leg off one side for the bolt the secure.
may need to remove the engine cover to see it. it is held down with allen key bolts.

Mar 25, 2011 | 2004 Nissan Maxima

1 Answer

Head bolt torque nissan altima 1995 2.4l


  1. Tighten head bolts using the following procedure:
  2. Tighten all bolts to 22 ftlbs.
  3. Tighten all bolts 59 ftlbs .
  4. Loosen all the bolts completely.
  5. Tighten all bolts 18 to 25 ftlbs .
  6. Turn all bolts 86 to 91 degrees.If an angle wrench is not available, mark all cylinder head bolts on the side facing the engine front. Then, turn each cylinder head bolt 86 to 91 degrees.
There you are as asked for.
Thank you for using FixYA
KL

Mar 05, 2011 | 1995 Nissan Altima

1 Answer

I need torque specks for valve train for a 1987 nissan truk v6 3.0 litter


cylinder head bolts 40 - 47 ft lbs, intake manifold bolts 12 - 14 ft lbs. , intake manifold nuts 17 - 20 ft lbs. , rocker arm shaft bolts 13 - 16 ft lbs. exhust manifold bolts 13 - 16 ft lbs. i hope this helps.

Dec 22, 2010 | Nissan Pickup Cars & Trucks

1 Answer

How do I fix a 1990 Nissan maxima head gasket?


to "fix" a head gasket requires taking off the cylinder head and associated compnents, getting the cylinder head serviced to ensure flat surface and no cracks, reaplcing the head gasket, and reassembly ensuring the proper torque of all bolts, especially head bolts........what makes you belive the head gasket requires fixing

Sep 15, 2010 | 1990 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...