Question about 1989 Toyota Pickup SR5

1 Answer

1989 toyota sr5 transmission

Truck has the v6 in it. Transmission is soaked with fluid and it doesn't want to move in fwd gear, but moves fine in reverse. Fluid was topped off. It has the automatic tranny. Think it's a 3vze.takes a lot of revs to move fwd.

Posted by on

Ad

1 Answer

I would say if you have a lot of oil everywhere you have some kind of source where the oil is coming from power wash area and check where this oil is coming from repair as needed or may require total rebuild

Posted on Nov 24, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
raycrazek
  • 106 Answers

SOURCE: landcruiser auto transmission,,how to check fluid level

when you open your hood look in the back of the motor on the left side.. you should see a stick with a circle on the end of it for your finger have you vehicle running warmed up that means let it run for 10 or 15 min. and then pull the stick out.. wipe it off real good. stick it back in all the way.. pull it back out and hold it horizontally and check it.. it's sometimes hard to read because it has bubbles on it.. try it a couple of times to get an accurate reading good-luck ray

Posted on Jan 16, 2009

  • 140 Answers

SOURCE: 2001 toyota Prerun/tacoma automatic transmission engages slowly

Change the filter.

Posted on Jan 23, 2009

  • 161 Answers

SOURCE: Overdrive light is flashing and tranny is slipping in drive and 2nd

my overdrive light is flashing due to a shattered speedo cable tip. check your fluid level. you may have to change the tranny filer and redo all the fluid.

Posted on Jun 11, 2009

  • 1 Answer

SOURCE: vault on automatic gear box on toyota estima enima

2.2td estima enima,the auto gearbox stopt change gear from 3 to 4,can somebody help me please?

Posted on Jan 16, 2011

  • 1 Answer

SOURCE: Transmission issue - almost no reverse & clacking

I've got exactly the same problem in '93 Camry w/5SFE automatic w/248,000mi. Transmission shop I trust told me ****** was gone. Another mechanic said the same. I'll drive it 'til the forward gears stop working. Forward L,2,D work great, except downshifting doesn't slow the car at all, although the engine goes to idle.

Let me know if there is any easy fix! Already did a fluid & filter change. . . .results no change. Thanks, cc

Posted on Sep 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 Toyota 5 speed manual w series transmission will only engage 4th gear. Why


Did you check the transmission fluid level? if it is OK, then you need to have a transmission specialist look into this.

Feb 27, 2015 | 1988 Toyota Pickup

1 Answer

My 94 Toyota celiac stars up but when I put in gear it won't move


Most possible ur transmission clutch r out.. if transmission fluid too low n u run it for sometimes the internal pump n the torque converter will damage too..

Apr 02, 2013 | 1994 Toyota Celica

1 Answer

Have an 05 cobalt with 110,000 mile. Car only moves while in reverse. When in drive or any other gear, the gear does nothing. I can move the shifter freely, but like I said. Unless in reverse, it...


CHECK TRANSMISSION FLUID LEVEL.IF OKAY.IF YOU HAVE NOT ALREADY DONE YET TRANSMISSION FLUID AND FILTER CHANGE IS DUE AT 100000 MILES.IF ALL IS GOOD YOU COULD HAVE FAULTY TRANSMISSION RANGE SWITCH.HAVE TRANSMISSION CODE SCAN FOR TRANSMISSION FAULT CODES.

May 24, 2011 | 2005 Chevrolet Cobalt

4 Answers

I put my truck in gear and i move no where. I can get into gear just as normal as when the truck did run. The rpm gets really high and i move nowhere.


This could be a clogged Transmission filter, bad torque converter, bad solenoid, disconnected shifting lever (not likely if you can put in park). If it's a standard it's most likely something you can fix on your own. If it's an automatic your most likely going to need to a service shop to do the rebuild.

Jul 22, 2010 | 1992 Toyota Pickup

1 Answer

I have a 89 toyota pickup 4 speed. When I'm stopped at a stop light, and let out on the clutch it seems like it has lost pressure. When I'm shifting down the road it shifts fine. I checked the fluid and it...


this sounds like the clutch slave is goin out, this unit is on the outside of the transmission. Possibly losing pressure!! Your transmission does not use transmission fluid, but instead gear oil. Have the following checked:
1. Clutch Slave (possibly worn)-this will cause soft or hard clutch pedal feel, slipping clutch, unintended clutch release, hard gear engagement, no/insufficient clutch movement.

*2. Clutch pedal Mounting Plate (possibly cracked)-this will cause improper gear engagement, hard gear engagement, soft pedal feel, insufficient clutch movement.

*this plate is located above the clutch pedal itself, apply pressure on the pedal with one hand while inspecting the plate for fatigue cracks(use a bright flashlight). This is very common on these models. This problem will eventually get worst and most mechanics never figure this out.

more questions email me at gimconsulting@ymail.com!!

Mar 15, 2010 | 1989 Toyota Pickup SR5

1 Answer

Truck wont go into 1st gear until truck warms up. Its a manual tranny. After it warms up its fine and runs and shifts fine. Im in NH and its 9 degrees here. Does temperature effect the tranny on the...


1989? When was the last time the Transmission was drained and new Transmission Fluid (oil) put in?
This Fluid (oil) loses viscosity and get particles in it causing additional loss in viscosity. I would go to even having the transmission drained and FLUSHED (cleaned) and new Fluid (oil) put in. Recheck the operation.
Boyles and Charles Laws are applicable here: (P*V)/T. Heat causes the Fluid to Heat and Expand (in molecules) but because of the limited sealed volume (transmission case) this increases Pressure allowing the smoother shifting and placement into gears.
Change the Transmission Fluid (oil) and have the Transmission Flushed (cleaning the insides) and your problem should go away.
Let me know if this helped, or if you have any additional information or questions. Feel free to contact me at FixYa.com!

Jan 30, 2010 | 1989 Ford Ranger

1 Answer

Bronco II: automatic Transmission slow to shift gears


replace the torque converter or try to get the transmission flushed first by a professional auto trans outfit

May 05, 2009 | 1989 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...