Question about Cars & Trucks

1 Answer

How do you take off a cv axle on a 99 dodge avengers from the transmission

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Filmmaker:

    Uploaded 5 video answers.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 14 Answers

You have to remove the tire then take the axle nut 34 or 36 mm socket remove the nuts on upper and lower ball joint take a hammer hit the spindle where the ball joint is the piece where the ball joint goes through it will spray if you hit it hard enough and disconnect the sensor wire going to the hub set spindle to the side tie it up with How do you take off a cv axle on a 99 dodge avenge - 8_31_2013_6_34_15_pm.jpeg

Posted on Aug 31, 2013

  • Skip Martin Aug 31, 2013

    Three tie straps now crawl under thecar with a pry bar and and catch next to the trans and jar it it will pop out it has a spring loaded ring so it's a little hard to pop out but it will come out

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 416 Answers

SOURCE: 1998 dodge avenger tranmission control solenoid

Below the link for Chrysler/Dodge auto-transmission manual
http://www.scribd.com/doc/7095618/545rfe-Transmission-Manual

Solenoid mounts outside the transmission, so you do not need to remove the transmission to install. It should be located between fuse box and air filter housing on the top of transaxle case and right next to transmission controle module.
I hope his step by step procedure will work for you. It is not hard at all to replace the solenoid. There are three 10mm bolts. You will also need to remove the input speed sensor. One thing to look out for is not bending the gasket when installing the new solenoid:

  1. Disconnect battery negative cable.
  2. Remove air cleaner assembly.
  3. Remove electrical connectors for transmission control module (please refer the manual I send you and autozone.com website).
  4. Remove the Transmission Control Module
  5. Disconnect and remove the input speed sensor
  6. Disconnect the transmission oil cooler lines. Cap off hoses and fittings to prevent foreign matter intrusion.
  7. Disconnect the solenoid/pressure switch assembly connector.
  8. Remove the three solenoid/pressure switch assembly-to-transaxle case bolts
  9. Remove solenoid/pressure switch assembly and gasket

Keep everything clean to prevent foreign materials to go inside
  1. Install solenoid/pressure switch assembly to case using a new gasket
  2. Install bolts and torque to 13 N·m (110 in. lbs.)
  3. Install 8-way connector and torque screw to 4 N·m (35 in. lbs.)
  4. Uncap and install transmission oil cooler lines.
  5. Install input speed sensor and torque to 27 N·m (20 ft. lbs.)
  6. Install Transmission Control Module
  7. Install air cleaner assembly.
  8. Connect battery negative cable.

P.s. 1. You can fine some clips on YouTube.com at least for similar cars
2. Also at Autozone.com you can find the component location for your car and repair guide
3. Also there is a link for Mitchel1 online manual useb by US mechanic 1 week subscribtion is
11.99 , 1 month 16.99
http://www.2carpros.com/kpages/auto_repair_manuals.htm
Let me know if you need more info
Good Luck and happy fixing

Posted on Jan 24, 2009

  • 4 Answers

SOURCE: front cv axle 1995 dodge intrepid

Naturally you need to remove the tire then the brake caliper. After the brake caliper is removed then you need to remove the 34mm axle nut that is inside the hub. After that is removed then you can remove the hub. Becareful not to damage the hub seal on the back or you will have to buy a new hub (100 or more). Then you need to remove the strut knuckle assembly. Once the knuckle assembly is removed then you can pull the CV axle. Take care the inner CV housing is held in place by an inner snap ring. You will probably have to pry off the inner housing. Once the axle is off then install the new axle (if you buy complete axle). Make sure if you are doing both that you take care which side you are installing. I made that mistake and double the work. Slide the new axle on the spline and make sure it is seated completely. Then put back together the reverse of removal.

Posted on Mar 24, 2009

emissionwiz
  • 76649 Answers

SOURCE: How to remove CV Axle from Manual Transmission on 2002 cavalier

the axle just pulls or snaps out of the trans, it is held in by an internal round spring clip, they are a real bear to remove the 1st time, u must pull straight out with a sharp jerking motion to get them to release, be patient it will come out.

Posted on Mar 31, 2009

  • 29 Answers

SOURCE: cv axle removal from transmission

take a pry bar to the side of the tranny and pry the cv out, there is a clip on the shaft of the axle on the inside of the tranny

Posted on May 15, 2009

  • 1071 Answers

SOURCE: 2008 dodge avenger. Will not move out of park.

ther is an electric solenoid in the shifter the fuse may have blown but if you have ever spilled anything sweet ,soda juice etc it will get sticky and gum up not letting it operate as designed check fuses first, if fuse is good then go to solenoid

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Slack between cv axle and transmission 99 accord


either the cv axle is worn or transmission bushings are failing

Oct 15, 2014 | Honda Accord Cars & Trucks

1 Answer

How do you remove the passenger side cv axle from a '97 dodge avenger?


You will have to replace the ball joint obviously, but go to Youtube and look for a video showing how to replace all of it. That would be your best way to go with a video showing you all the detail

Jul 25, 2014 | 1997 Dodge Avenger

1 Answer

Repair cv joint seal


Are you asking about the boot on the CV joint, or the transmission seal where the CV joint axle fits into the transmission?

Jun 13, 2012 | 1995 Dodge Stratus

1 Answer

I have a dodge caravan 96. Motor is 3.3. I have a transmission leak. On the driver side of the transmission. I replace the seal, but the leak continue through the CV joint.


If it is leaking grease out of the cv joint, you will have to replace the rubber cv boot or eventually, the entire cv axle, if it gets worn because of lost grease and no lubrication.

Sep 22, 2010 | 1996 Dodge Caravan

1 Answer

How do you change a cv joint on a 1992 dodge caravan? The right cv joint is out. Do we need to replace the right axel or can we just change the cv joint?


You need to replace the whole right side axle shaft. Take the ball-joint loose and the axle nut. Pull the shaft from the hub assembly and then pull it from the transmission

Mar 28, 2010 | Dodge Caravan Cars & Trucks

1 Answer

95 avenger transmission leaking


is it the same seal? it sounds like something was not installed good, or a burr on the axle, i would get a second look at another garage to see exactly whats going on, then take it back to the shop that rebuilt it, if it the same seal it could be a defective axle, good luck hope this helps.

Dec 12, 2009 | 1995 Dodge Avenger

1 Answer

My 96 has a small clunck when i start going forward or reverse. how can i fix this?


sounds like you have a cv joint going out and ready to leave you stranded . get it checked . new axle /150$ fix labour extra unless you do yourself , dont quote my price . if it's your transmission it will be alot higher but start at the cv joints for clunk's. you also have hubs in the front that click / bad bearing clicking noises dont really sound like clunk noises. clunks come from the axles .

Nov 29, 2009 | 1996 Dodge Avenger

1 Answer

My van makes clicking noise when going uphill & and sometimes the speeds slows right down and makes noise (clicking under vehicle).


Could be front CV axles making that noise. Check out the rubber cv boots going from the transmission to the center of the front wheels, If the boots are ripped or cracked, replace the cv axles on both sides.

Apr 22, 2009 | Dodge Caravan Cars & Trucks

1 Answer

Mysterious transmission leak of 99 dodge avenger


Check the cooler lines, they will only leak when it is running.

Mar 13, 2009 | 1999 Dodge Avenger

1 Answer

My 99 dodge avenger overdrive its ok to turn off on the street???


most people drive with it on...it dosent hurt the transmission

Jan 29, 2009 | 2000 Dodge Avenger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...