Question about Cars & Trucks

Open Question

Mazda titan 1994

Which way do you turn the adjuster to tighten front brakes

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: how to install front brake pads on a 1994 mazda pickup

POSSIBLY SOMEONE HAS ADJUSTED THE ROD BETWEEN FOOT PEDAL AND MASTER CYLINDER OR STICKY/SIEZED CALIPER SLIDES

Posted on Jun 01, 2008

  • 59 Answers

SOURCE: adjusting the e brake

Your emergency brake line is on the back driver side tire and will either tighten down with a screw driver or a wrench will work. Righty tighty lefty loosy.

Posted on May 17, 2009

  • 4793 Answers

SOURCE: i want to know the GVW of mazda titan truck 1994

gvw is written/stamped on chassis plate.

Posted on Mar 31, 2010

HansPP
  • 2510 Answers

SOURCE: I was attempting to adjust

Any competent mechanic should be able to fix that, it is a reasonably straight forward procedure and does not require any special tools or equipment.

Posted on Apr 27, 2011

  • 3 Answers

SOURCE: adjusting the parking brake on a 2001 mazda protege

under the driverside should be a cable and a adjusting nut and bolt

Posted on Oct 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the torque spec for the front wheel bearing on a 1964 Chrysler New Yorker?


http://www.automobile-catalog.com/make/chrysler/full-size_chrysler_4gen/full-size_4gen_new_yorker_sedan/1964.html

http://www.automobile-catalog.com/auta_details1.php
25607247-yjo0ud12y22pkmokvfqa1yzz-2-0.gif
NOTE: Always install a new hub nut. The original hub nut is one-time use only and should be discarded when removed.
11. Install hub nut on end of halfshaft stub shaft. With aid of a helper applying brakes to keep front hub from turning, tighten hub nut to 160 N·m (118 ft. lbs.).
12. Install tire and wheel assembly. Install and tighten wheel mounting nuts to 135 N·m (100 ft. lbs.).
13. Lower vehicle.
14. Pump brake pedal several times to ensure vehicle has a firm brake pedal before moving vehicle.
15. Check and adjust brake fluid level as necessary.

Mar 25, 2015 | Chrysler New Yorker Cars & Trucks

3 Answers

How do I adjust the parking brake on chevy s-10 1994


Under the truck, on the drivers side, about in the middle of the truck is where the adjustment is. You will see the cable from the front going to the back. There is a long threaded bolt on the end on the cable. Lube it up good. and adjust it. If you can't get a good adjustment, replace the front cable, it is stretched to far.

Oct 13, 2014 | 1994 Chevrolet S-10

1 Answer

1999 plymouth breeze. step on brakes and the front brakes have a bad pulsing to them. previous owner hab brakes done rotars turned and pads replaced. any suggestions on how to address this problem


Symptom: Brake Pedal Pulsates Change When: Braking Change Where: Passenger Compartment Change -->lg-bl.jpg lg-br.jpg
Priority Action Part Type Cause 1 Inspect Brake Drum Specs Brake Drum Out of Adjustment, Out of Round, or Cracked. 2 Inspect Brake Drum Unevenly Worn or Out of Round Brake Drum(s). 3 Inspect Brake Rotor Incorrectly Machined Brake Rotor. 4 Inspect Wheel Bearing-Front Incorrectly Tightened or Installed Wheel Bearing. 5 Inspect Wheel Bearing-Rear Incorrectly Tightened or Installed Wheel Bearing. 6 Inspect Wheel Nut Loose, Worn, or Damaged Wheel Nut(s). 7 Inspect Rear Axle Bent Rear Axle.

Apr 13, 2013 | Plymouth Breeze Cars & Trucks

2 Answers

Adjusting the parking brake on a MiTSubichi ENDEAVOUR 2005


If your parking brake is too loose or is not properly adjusted, you may encounter problems while parking, positioning and driving your car. Most of the time, car owners would send their car to a mechanic in order to fix and tighten the parking brake. However, you can actually skip this step and adjust your parking brake yourself. When your car starts to slip on a hill in its park position, you need to start tightening the parking brake.1 Remove the car's center console cover placed around your parking brake level inside your car. This is found between the seat of the driver and the front passenger.2 Use your wrench to turn its adjuster nut found at the end of your parking brake's cable rod. Loosen the adjuster nut with your wrench, while making sure that it does not come off at your parking brake cable rod's end.3 Raise your car rear wheels using your jack, and use your jack stands to support both its rear wheels.4 Pull up your parking brake handle up to two clicks or notches. Tighten your adjuster nut until you feel a slight resistance on your rear wheels whenever you spin them.5 Release your parking brake lever. Check and make sure that your rear wheels are still able to spin freely and without any resistance.6 Pull up on your parking brake lever up to three to five clicks or notches, while making sure that your car's rear wheels are not turning at all.7 Lower the car by adjusting your jack, and remove your jack stands from your car's rear wheels.

Oct 03, 2011 | 2005 Mitsubishi Endeavor

1 Answer

Adjusting the parking brake on 03 pontiac vibe


If you look under the van on the driver side (usually) you'll see where the two cables from the rear inter-connect with the main cord to the front. Here, you should find an adjustable bolt that you can tighten. If it is not here, it may need to be tightened from there rear tires.

If you have drum brakes in the rear, these are most likely "self-adjusting" brakes, which may interact with the emergency brake. Everytime you back up, and apply the brakes, you are activating the self adjuster (you would have seen this located at the bottom of the brake system between the two brake pads. This is the self adjuster. Try going in reverse at about 5 miles per hour, and hitting the brakes firmly (not slamming on them). Drive forward again, and firmly press the brakes. Go in reverse again, and apply brakes firmly again; (do this about 4 or 5 times to get the rear brakes adjusted). Try the emergency brake again and if still not tighter, purchase or look in your repair manual as to how to adjust the emergency brake.

Please let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

May 29, 2010 | 2003 Pontiac Vibe

1 Answer

How do you adjust the parking brake on a 1994 ford ranger,manaul trans,4wd


Start by adjusting up the rear brakes, if those are tight and you still want to tighten up the parking brake running down the driver's side, outside the frame are the parking cables. somewhere around the back of the cab/front of the bed should be a plate with 2 cables and a bolt. tighten the bolt/nut up to make the parking brake tighter

Oct 04, 2009 | 1994 Ford Ranger Supercab

1 Answer

Need to tighten emergency brake on 1997 toyota 4runner


if you need to tighten the cable under the vehicle you will find where the single cable from the front connects to the two rear to tighten set the emergency brake six to seven clicks and tighten nut until the brakes catch. if you need to adjust the actually brakes in the drum set the ebrake the same setting find the little rubber plug on the backing plate remove get a small flat head screw driver and flash light find the little gear inside use the screwdriver to turn will only go one way turn the gear until brakes grab and wheel can't be turned.

Aug 30, 2009 | 1997 Toyota 4Runner

1 Answer

Loose emergency brake on 2004 Saturn Vue


  1. Apply and fully release the park brake several times. Verify that the park brake lever releases completely.
  2. Turn ON the ignition. Verify the red BRAKE warning lamp is not illuminated.
  3. If the red BRAKE warning lamp is illuminated, verify the following:
    • The park brake lever is in the fully released position and against the stop.
    • There is no slack in the park brake cable.
  1. Turn OFF the ignition.
  2. Disable the SIR system.
  3. Remove the front floor console.
  4. With the park brake lever in the released position, using ONLY hand tools, loosen the adjusting nut completely to the end of the front cable threaded rod.
  5. Raise and support the vehicle.
  6. Remove the rear tire and wheel assemblies.
  7. Adjust the rear drum brakes.
  8. Ensure there is no brake shoe drag after adjustment by rotating the brake drums. If drag exists, re-center the brake shoes and perform the brake shoe adjustment again.
  9. Install 2 wheel nuts to the wheel studs and firmly hand tighten in order to retain the brake drums.
  10. Lower the vehicle to permit access to the park brake lever.
  11. Raise the park brake lever 1 detent position. Notice: Refer to Fastener Notice in Service Precautions.

Jan 14, 2009 | 2004 Saturn VUE

1 Answer

Jeep grand cherokee revs for to high before changing gear


Message:
My 2002 Dakota has been somewhat confused about shifting as well. It showed a code P1762. I dropped the pan to install a new fluid filter and fluid-(use only ATF+3 or ATF+4). Since the pan was off I decided to adjust the bands. The front band controls the 2nd gear cluster. The rear band controls the 3rd gear cluster and reverse. For a 2-3 shift, the transmission shifts back to 1st gear with the front band while the rear band engages 3rd gear. If the front band does not release the 2nd gear clutches before the third gear clutches engage, the transmission binds, which shortens the life of the transmission clutches. If the front band releases too early in the shift, the engine will overspeed (sounds and feels like a slip) during the 2-3 shift.
The front band adjusting screw is on the driver's side above the shift linkage. The rear band is inside the fluid pan near the filter.
1. Loosen band adjusting screw locknut. Then back locknut off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw
threads if necessary. The front band adjuster is on the outside of the transmission and the locknut requires a 3/4" wrench.

2. Using Inch Pound Torque Wrench C-3380-A, a 3-in. extension and appropriate Torx� socket (T-40), tighten adjusting screw to 72 in-lb. CAUTION: If Adapter C-3705 (from SPX Miller) is needed to reach the adjusting screw, tighten the screw to only 47-50 in. lbs. torque.

3. Back off adjusting screw the number of turns listed below for your transmission.

4. Hold adjusting screw in place and tighten lock-nut to:

41 N�m (30 ft. lbs.) for the front band
34 N�m (25 ft. lbs.) for the rear band
The adjustment screw inside the case is a square head bolt. You will need a 1/4 square head socket to fit your torque wrench.
Band adjustments for each model year:
1994

* Front Band - tighten to 72 in-lb, back off 2-1/2 turns (all transmissions)
* Rear Band
o 32/42RH - Tighten to 72 in-LB, back off 4 turns
o 36/37/46/47RH - Tighten to 72 in-lb, back off 2 turns

1995-1996

* Front Band
o 42RH - tighten to 72 in-lb, back off 2-1/4 turns
o 46RH - tighten to 72 in-lb, back off 2-7/8 turns
o 47RH - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE/RH - tighten to 72 in-lb, back off 4 turns
o 46RE/RH - tighten to 72 in-lb, back off 2 turns
o 47RE/RH - tighten to 72 in-lb, back off 3 turns

1997-1998

* Front Band
o 42RE - tighten to 72 in-lb, back off 3-5/8 turns
o 46RE - tighten to 72 in-lb, back off 2-7/8 turns
o 47RE - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE - tighten to 72 in-lb, back off 4 turns
o 46RE - tighten to 72 in-lb, back off 2 turns
o 47RE - tighten to 72 in-lb, back off 3 turns

1999

* Front Band
o 42RE - tighten to 72 in-lb, back off 3 turns. (TSB 21-16-98)
o 47RE - tighten band adj. screw to 72 inch pounds, back off 1 7/8 turns
* Rear Band
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns
+ The 47RH rear band requires a 1/4" hex driver, the front band requires a
T-30 Torx driver, the filter is held in place by two screws which require a T-20 Torx drive

2000-2002

* Front Band
o 42RE - Tighten band adj. screw to 72 in-lb, back off 3 turns
o 44RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
o 46RE - Tighten band adj. screw to 72 in-lb, back off 2 7/8 turns
o 47RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
From Bill Konolday's 47RE notes: I usually go a little looser than factory
specs on this front band - backing off the adjustment screw 2 or 2 1/4 turns.
Depending on the circumstances I have backed off the band up to 2 1/2 turns.
* Rear Band
o 42RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 44RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 46RE - tighten band adj. screw to 72 inch pounds, back off 2 turns
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2003

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 1-3/4 turns
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2005

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds,
back off front band adjusting screw 1-3/4 turns for diesel vehicles,
or 1-1/2 turns, for V-10 vehicles.
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

94+ Automatic Transmission Bolt and Nut Torque Specs

* Front band adjustment locknut - 30 ft-lb
* Rear band adjustment locknut - 25 ft-lb
* Transmission pan bolts - 13 ft-lb
I just replaced the solenoid with the recommended transducer and all is fine now. The transducer cost me about $50 at a nearby dealership.
Hope this helps. -zman. rroszman@yahoo.com

Dec 09, 2008 | 2001 Jeep Grand Cherokee

2 Answers

Toyota yaris


The handbrake adjustment is at the handbrake. Pull off the rubber boot around the hand brake. (it pulls open at the botto of the handle and slips off over it). Next locate the 10mm bolt under the rear cup holder (there may be a little felt in there covering it). Remove the bolt.

Lift the console at the rear, it should pop loose at the front and lift up. You should have clear access to the adjustment bolt. Loosen the 10mm locking nut and this should allow you to adjust the cable.

Turn the adjustment clockwise to tighten the cable and once adjusted, re-tighten the locking nut. Reverse the whole process to put the console etc back together.

Aug 17, 2008 | 2007 Toyota Yaris

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...