Question about 1991 Ford F150

Open Question

1991 f150 4.9ltr. tfi ignition no spark - 1991 Ford F150

Posted by Anonymous on


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Vehicle cranks but will not start no fire

Common Fox Mustang issue related to this condition would be a faulty coil,ignition connection under steering wheel melted,faulty or the TFI Module on the Dizzy. I would start with the TFI 9 times out of 10 this is the culprit. Be sure to replce it with a motorcraft as Ive had bad experinces with aftermarket TFI modules right out of the box. I've attached a photo of the TFI module below. Good Luck Ryan MN

Apr 19, 2014 | 1987 Ford Mustang

2 Answers

Where is the Ignition Control Module located on a 1992 Ford E150 Econoline van?

After 1991 ford moved the TFI from the distributor to the left fender next to the coolant bottle under the hood.

Jul 12, 2011 | 1992 Ford Econoline

1 Answer

How do I repalce ignition module on 1991 F150 inline 6 cylinder 2 wheel drive

  1. Remove the distributor cap from the distributor, and set it aside (spark plug wires still connected).
  2. Disconnect the harness connector.
  3. Remove the distributor.
  4. Remove the TFI module retaining screws.
  5. To disengage the TFI module's terminals from the distributor base connector, pull the right side of the module down the distributor mounting flange and then back up. Carefully pull the module toward the flange and away from the distributor.
  6. Coat the TFI module baseplate with a thin layer of silicone grease (FD7AZ-19A331-A or its equivalent).
  7. Place the TFI module on the distributor base mounting flange. Position the module assembly toward the distributor bowl and carefully engage the distributor connector pins. Install and torque the two TFI module retaining screws to 9-16 inch lbs.
  8. Install the distributor assembly.
  9. Install the distributor cap and check the engine timing.

May 16, 2011 | Ford F-150 Cars & Trucks

1 Answer

I have a91 f150 nite no spark replaced distributer and coil got power to coil but no spark can someone help I don't get online alot so out would be greatly appriceated if you could txt me 248 974 0281 plz...

Sorry I don't do text, because I don't want spam either... The most likely cause of your problem is a bad TFI (ignition) module. All of the engines used in Ford trucks in 1991 used the TFI modules. Some were distributor-mounted modules and some were fender-mounted modules. I cannot tell you where yours is actually located, because you did not bother to mention engine size. (Nice-to-know information - it helps a little if we know what we are working on) Anyway, That is the most likely cause of a no-spark condition. In fact, It has been so common with the Ford engines that Ford ended up settling in a class-action law suit due to the TFI modules repeatedly leaving people stranded. I personally had a Ford Ranger - replaced the TFI module about 6 times in the 7 years that I owned it...used to keep a spare in the glove box.

Apr 20, 2011 | 1991 Ford F150

1 Answer

No spark

I would check the fuses and relay for the EEC IV. You probably have a bad TFI ignition control module, the gray box bolted to the side of the distributor. Auto Zone should be able to test it. Also, check the pick up coil inside the distributor.

May 31, 2010 | 1991 Ford F150

2 Answers

87 ranger wont spark....New coil, and pickup coil

Check to see if the rotor button is turning,that will tell you if the timing belt is broke or not,also,the ignition module tfi module is most likely the problem if the timing belt is not broke.

May 19, 2010 | 1987 Ford Ranger

2 Answers

My car has no spark it has a new crank senor i tested the ecm it passed so what could it be

it is mounted on the side of the ignition distributor body, here is a picture, u should also change the Stator inside the distributor, this requires you remove the distributor from the engine and then drive out the roll pin that holds the drive gear on, this is not for the do it yourself-er

TFI Module picture


Dec 01, 2009 | 1991 Chevrolet Lumina

1 Answer

Has no spark not getting 12 volts to tfi or coil

these have a problem with the ignition starter switch, replace it.

Sep 26, 2009 | 1991 Ford Probe

1 Answer

1995 ford taurus 3.0l v6 wagon no spark.

Listen TFI module is more than likely the problem change it. TFI module controls spark and timing and fuel. Keep one with you in the car. The module is getting hot and not working right.

Jun 16, 2009 | 1995 Ford Taurus

Not finding what you are looking for?
1991 Ford F150 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides