Question about Cars & Trucks

1 Answer

I have a 2004 Bonneville an can"t figure out how

Posted by on

  •  Brad
    Brad Jul 14, 2013

    You may need to repost your question. I know less about how this fixya site works than I'd like. No help menu here. But it seems that once anyone gives an answer to a question, that question is removed from the unanswered quick view list. And I can't figure out how other techs can find it & join the discussion. If you repost I'll not give an answer so some one else can try to help you out.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 85 Answers

This option should be controlled though the radio. You'll need to follow instructions in owner manual.

Posted on Jul 12, 2013


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 141 Answers


Pull the bulb out of both left side turn signals and check the filaments. As these are double filament bulbs, sometimes the filaments break and lay across the other creating a feedback issue.

Posted on Jan 15, 2009

  • 2 Answers

SOURCE: Brake light, Turn signal not working rear right 06' Focus

I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems

Posted on Aug 06, 2009

  • 436 Answers

SOURCE: 2004 monte carlo. turn signals dont work. the

try pressing the hazards on and off if they still don,t work replace the flasher unit. it is built into the hazard switch( all one unit ) change this and all will be good.

Posted on Aug 30, 2009

  • 1632 Answers

SOURCE: 1999 ford crown vic dash light running light problem.

Check all the bulbs at tail end for parking and brakes, test grounds and harness for trailer. Check fuses. clean batery terminals, Re instal head light swich properly and make sure all wires conect.

Posted on Sep 09, 2009

Testimonial: "thank you for quick response will try all of your suggestions will re post if no luck."

  • 119 Answers

SOURCE: VW Transporter,replaced the indicator stalk/switch but indicators

First check that the new switch is an EXACT match to the one you removed. There are a number of different switches that will all fit on to the column, but do not match exactly.
Re check that ALL the plug connections are fully pressed into place.
This is usually the problem and is an easy error to make
Good luck

Posted on Dec 17, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Flasher relay location Pontiac Bonneville 2004 removal and installation.

If the right side works it's not your flasher, Its your left side bulb, either front turn signal or rear tail light bulb.

Aug 02, 2014 | 2004 Pontiac Bonneville

1 Answer

Check oil light

Vehicle Systems do not monitor oil level & how clean it is

Stop using it & have it figured out

Oct 08, 2012 | 2004 Pontiac Bonneville

1 Answer

How do i turn off my check gauge light in my 04 bonneville

If you turn the check light off, you will erase the
codes you will need to start a diagnostic process.

Most times you get any light on your dash & you can
expect at least one a year,your vehicle is in need of repair

Check for codes & repair code related issues first

A code does not tell you any parts need to be replaced

A code directs you to a system & possibly a part of a system
that you need to do some testing on

Aug 30, 2012 | 2004 Pontiac Bonneville

1 Answer

2004 Jeep Grand Cherokee temp gauge high when heat is on

If your "check engine" light is turn on, I suggest scanned the PCM to know exactly what fault code is stored there. Additionally, could be some problem with the "temp sending unit".

Keep us updated.

Jan 23, 2012 | 2004 Jeep Grand Cherokee

1 Answer

My car will not stat but everything else turns on. My display reads "service Theft System" and the lights that stay on are the "security, battery, and service engine." Is it possible...

a bad key will cause this try your spare key to see if it will start if your battery is bad replace it but this will not cause all these lights to come on with your spare key lock all the doors then unlock the driver door with the key then try to start the car let me know what happens

Feb 02, 2011 | 2002 Pontiac Bonneville

1 Answer

I have replaced the rear brakes pads on my 2004 pontiac bonneville - and now everytime i touch the brakes lightly - it makes a strange noise - Wayne

did you put wagner pads with built in shims, or another brand that has separate shims for the back of the pads?

Jul 11, 2010 | 2004 Pontiac Bonneville

1 Answer

The cruise control on my 2004 Bonneville Pontiac stopped working. I checked to fuse and it is still good. What could be the possible problem?

Check to see if the third brake light works. The brake switch works both the crusie and the 3rd brake light

Sep 14, 2009 | 2004 Pontiac Bonneville

1 Answer

2004 bonneville. head lights will not turn off..

Find and replace the headlight relay - its probably sticking relay contacts.

Aug 09, 2009 | 2004 Pontiac Bonneville

1 Answer

2004 Pontaic Bonneville humming noise wheel bearing?

I had a similar problem, when turning to the right or on a right curve, the noise would go away. After some research I found it was the left wheel bearing assembly. I replaced it and the problem is gone. Therefore, check the wheel bearing assembly. You may have to replace it.

Jun 03, 2009 | 2004 Pontiac Bonneville

1 Answer

2004 Pontiac Bonneville Check Engine Light

do you fill the gas tank with the key on?

Try disconnecting the battery for 1/2 hour an then reconnect and drive for 10 miles. It may run rough for this period. This will clear codes from memory.

May 27, 2009 | 2004 Pontiac Bonneville

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides