Question about 2001 Bentley Arnage

1 Answer

Relay my 1999 Bentley Arnage a/c compressor clutch is not engaging normally. with direct power to compressor it works and blows cold

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Bentley Master
  • 21,873 Answers

Have you checked the low and high pressure switches ?

Posted on Jul 12, 2013

Testimonial: "i have changed the pressure switch on the top of the dryer. where is this other switch located? "

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 491 Answers

SOURCE: continous check engine soon light

take it to the dealer

Posted on Dec 27, 2008

Murphybanton
  • 2004 Answers

SOURCE: how many qts of oil does 6.8L 2001 bentley arnage

6 qts

Posted on Jun 09, 2009

  • 1 Answer

SOURCE: 2003 Bentley Arnage navigation system display malfunction

Hi Bill,

I now have the workshop manual set that covers the Bentley Arnage (1998-2009).

Please let me know if you still need this.

Thanks again,

Sheila & Larry
http://www.ModCollectibles.com
http://mutley.hypermart.net/RollsSubstituteParts.html


bhart2341 wrote:
Do you have a CD Workshop Manual for the 2000 Bentley Arnage Red Label?

Bill Hart

Posted on Apr 14, 2010

SOURCE: how do I reset the

To reset the service engine light on a 2000 Bentley Arnage, turn the key to the second stage, one being accessories. Now press the trip and cancel buttons together and hold them for about five to seven seconds, the display will show nothing. Now press again immediately for about five to six seconds and it will go into change mode. The vehicles serial number will be shown where the mileage was displayed. Now use the trip button only to navigate to the sign reading "service due" then hold down the cancel button until it changes color from green to red or vis versa then it will beep. Press cancel and then turn the ignition off and restart your car.

Posted on Dec 14, 2010

  • 1 Answer

SOURCE: how to reset service light ,on Bentley Arnage 2000

MICHAEL34 IS CORRECT

Posted on Dec 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to charge Bentley arnage 1999 battery


Both are necessary to start the engine, so charge them both.

Aug 21, 2016 | 1999 Bentley Arnage

1 Answer

LOOKING FOR A/C RELAY


What kind of car are you working on? Most of the time the relay is in the command switch unless you have some form of temp sensor also your hi/lo pressure switch controls the a/c command

May 27, 2015 | 1999 Bentley Arnage

1 Answer

Help 2008 ford fusion heater and ac stopped working


1) TEST the fuse+ relar of a/c
see the next steps and fix it. God bless you
If so, the compressor is working and the A/C system probably contains enough refrigerant to make cold air, so the problem is inside the HVAC unit. Replace the motor that controls the blend air door (this is a difficult job and best left to a professional since it involves tearing apart the HVAC unit -- about an 8 to 10 hour job!).
If the compressor does not engage when you turn on the A/C, see if it will run by jumping the compressor clutch wire directly to the battery (use a fused jumper wire). If the compressor works when you jump it, and the A/C blows cold air, the system contains refrigerant and the fault is likely a bad A/C compressor clutch relay or a bad clutch cycling switch or pressure switch.
If the compressor does not engage when you jump it, the problem is a bad compressor clutch.
If the clutch engages but the compressor does not turn (the belt will start to slip and squeal), the compressor is locked up and you need a new compressor.
If the compressor clutch engages and turns the compressor, but the A/C still does not blow cold air, the system is probably low on refrigerant and needs to be recharged

10_5_2012_12_00_24_pm.jpg

Oct 05, 2012 | 2008 Ford Fusion

1 Answer

Ac vent blower


proceed according and fix it. God bless you
If so, the compressor is working and the A/C system probably contains enough refrigerant to make cold air, so the problem is inside the HVAC unit. Replace the motor that controls the blend air door (this is a difficult job and best left to a professional since it involves tearing apart the HVAC unit -- about an 8 to 10 hour job!).
If the compressor does not engage when you turn on the A/C, see if it will run by jumping the compressor clutch wire directly to the battery (use a fused jumper wire). If the compressor works when you jump it, and the A/C blows cold air, the system contains refrigerant and the fault is likely a bad A/C compressor clutch relay or a bad clutch cycling switch or pressure switch.
If the compressor does not engage when you jump it, the problem is a bad compressor clutch.
If the clutch engages but the compressor does not turn (the belt will start to slip and squeal), the compressor is locked up and you need a new compressor.
If the compressor clutch engages and turns the compressor, but the A/C still does not blow cold air, the system is probably low on refrigerant and needs to be recharged

10_5_2012_12_14_20_pm.jpg

Oct 05, 2012 | 2001 Oldsmobile Aurora

1 Answer

My air conditioner is blowing warm air on the driver side and cold on the passenger side


see this steps and think with clearly and logically NOT feared. God bless you
checkmark.gif Start with the compressor. Does it engage when you turn on the A/C?
If so, the compressor is working and the A/C system probably contains enough refrigerant to make cold air, so the problem is inside the HVAC unit. Replace the motor that controls the blend air door (this is a difficult job and best left to a professional since it involves tearing apart the HVAC unit -- about an 8 to 10 hour job!).
If the compressor does not engage when you turn on the A/C, see if it will run by jumping the compressor clutch wire directly to the battery (use a fused jumper wire). If the compressor works when you jump it, and the A/C blows cold air, the system contains refrigerant and the fault is likely a bad A/C compressor clutch relay or a bad clutch cycling switch or pressure switch.
If the compressor does not engage when you jump it, the problem is a bad compressor clutch.
If the clutch engages but the compressor does not turn (the belt will start to slip and squeal), the compressor is locked up and you need a new compressor.
If the compressor clutch engages and turns the compressor, but the A/C still does not blow cold air, the system is probably low on refrigerant and needs to be recharged.

7_25_2012_8_45_21_am.jpg

Jul 24, 2012 | 2007 GMC Sierra Classic

1 Answer

My 2002 Expedition air conditioner will sometimes blow hot air and others cold air


I would check the following possibilities:
1. Is compressor clutch working? - You need to do this when the ac is blowing hot air only - locate compressor drive pulley on engine - rubber belt wraps around it. Start engine and set to max ac. When the ac is blowing hot air, look at the center of the compressor drive pulley using a good flash light - watch it for a while, it should be spinning with the pulley - this means the compressor is engaged. If not, the compressor is not engaged. If your ac is blowing hot air, then the compressor should be engaged and running (trying to cool). If it is not engaged, then your compressor clutch is probably going out. Could be low voltage to clutch, but more likely the clutch is worn out and only working some of the time. Note: if working normally, the compressor clutch will engage and disengage in cycles- but the air should always be cold. If clutch is bad, compressor would need to be replaced (sold as one unit). This is tricky to diagnose and could take some time - you need to do it when ac is blowing hot air but set to max cooling.

2. Low on refrigerant or refrigerant has moisture in it? If your ac blows cold initially after being off for a while, then heats up, and continues to regularly cycle back and forth between hot and cool air, then the system may be low on refrigerant or the refrigerant may have moisture in it that is freezing and restricting refrigerant flow. An a/c shop can check refrigerant level and even replace refrigerant if moisture is suspected.

Could be other issues, but I would start with these.

Good luck

May 07, 2010 | 1999 Ford Expedition

1 Answer

1999 Bentley arnage will not start replaced battery but seems to be locked out starter & fuel relay from alarm. can this be bypassed or reset without going to the dealer!


DO NOT TRY TO BYPASS! go to the dealer and have them show you how. you have a very fine vehicle. dont "mickey mouse" the repairs. ive worked on older bentley and rolls royce so feel free to contact for further repair info. cheers.

Dec 02, 2009 | 2001 Bentley Arnage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bentley Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Are you a Bentley Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...