Question about Honda Cars & Trucks

1 Answer

Code p1381 Car starts then cuts off ,hesitates when pressing on gas peddle

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 954 Answers

Error Code P1381: Cylinder Position Sensor Intermittent Interruption.
Fault:
- Cylinder Position Sensor defective.
- Wiring, loose connections, dirty connector.
- ECM

Posted on Jan 07, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: car started to sputter on

Fuel filter is a good place to start as per "guest". Does it do this all the time, for example, when cool in the morning, first started, does it run o.k. then or the same?

Posted on Aug 23, 2008

  • 328 Answers

SOURCE: car hesitates when press gas and engine light on

could be ur transmission shift solenoid

Posted on Apr 08, 2009

Molson02536
  • 3854 Answers

SOURCE: My car will start and then after a minute or two

First scan the PCM for trouble codes using a hand held engine scanner, Then repair codes by replacing failed sensor as needed.  If no codes are present try replacing the idle air control motor. 
Auto Zone will scan your car for codes for free so you know what your going to have to replace and they do have a how to do it your self instructions to what your going to replace.
Good luck and hope this helps

Posted on Apr 20, 2009

  • 1 Answer

SOURCE: Acura Integra is Hesitating when I apply the gas badly!

make sure that the plugs you changed were the recommended ones for your car. I own a 2000 integra and a boyfriend decided he wouldn't listen to me and put new plugs and wires other than the platinum plugs that it called for. i had problems with it and i went and bought the platinum ones and it ran fine after that. always change the distributer cap along with the plugs and wires.

Posted on Dec 31, 2009

  • 14036 Answers

SOURCE: How to fix the P0455 error code in a Kia Optima

COULD BE HAVING PROBLEM IN THE EVAP PURGE VALVE ITS DAMAGED OR FAILED.

Posted on Jan 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 98 chevy lumina with 61k miles.what can I do about these codes, P0300. P1381


P0300 is a random or multiple cylinder misfire, and P1381 is a misfire EBCM (Electronic Brake Control Module) or PCM (Powertrain Control Module) Since you mentioned replacing fuel components, it could be as simple as a fuel injector being clogged up causing a cylinder misfire. Have you checked your fuel injectors?

Jan 21, 2015 | Cars & Trucks

1 Answer

I am having a problem with my 1998 Kia Sophia and what is happening is when I start my car it idles really rough and then when I press on the gas peddle it stalls out I thought it could be because it was...


Possibly blocked fuel filter, when you press the pedal it starves the engine or fuel causing it to cut out. Only a few quid for a fuel filter so I'd start there

Dec 01, 2013 | 1998 Kia Sephia

1 Answer

Hesitation when step on gas


probably just needs a tune up spark plugs and wires

May 29, 2013 | 1998 Pontiac Grand Am

1 Answer

My car hesitate to drive when placed in drive and stepping on the gas peddle then cuts off 1996 lexus 300. please help


Worked on truck dodge truck about a year ago that done the same thing,it would start up fine and when put into drive it would run rough or simple quit. I changed the crank and cam sensors on fixed the problem.. hope this helps and good luck...Please rate this post.

Aug 14, 2012 | 1996 Lexus ES 300

1 Answer

When i press on the gas peddle the car hesitates and jerks. If I do it slowly it doesn't do this... But, you can't press hard on the gas peddle or it will hesitate.


I think your car is runing Lean and i would say check the Mass air flow sensor and the fuel system because your car seems like its sucks more air then fuel. Do you have any check engine light on ?

Dec 28, 2010 | 2000 Pontiac Montana

2 Answers

When I press the gas peddle, there is a hesitation in the engine, also while driving the car sputters and hesitates while my foot is on the gas. What can I do to fix this?


I would start with replacing the fuel filter, if it hasn't been done in a while. Also, check the air filter. Do you have any check engine light?

May 26, 2010 | 1998 Chevrolet Cavalier

1 Answer

Hesitates start an when i stop it cuts off


you should not have to work the gas pedal to start this car. It has an electric fuel pump. When you turn the key on to start it can you hear a "whirring" sound coming from the back of the car? Get your fuel pump checked.

Mar 10, 2010 | 2000 Dodge Avenger

1 Answer

My 2000 Yukon engine hesitate


Chk MAF sensor (mass air flow) first sensor in ducting coming out of air filter.

* Use only one foot on the gas peddle - Just teasing. :)

May 22, 2009 | 2000 GMC Yukon

1 Answer

My car will start and then after a minute or two of running, the car will idle down and cut off but I can start it right up again and still get the same results. Whenever I put it into gear to drive it...


First scan the PCM for trouble codes using a hand held engine scanner, Then repair codes by replacing failed sensor as needed.  If no codes are present try replacing the idle air control motor. 
Auto Zone will scan your car for codes for free so you know what your going to have to replace and they do have a how to do it your self instructions to what your going to replace.
Good luck and hope this helps

Apr 20, 2009 | 1997 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...