Question about Cars & Trucks

1 Answer

Where does oil sensor go in a 2006 dinali - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,108 Answers

In the oil pan.

Posted on Jul 12, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How will a 2006 monte carlo ls act if the oil pressure sensor is out


not too sure, but you can take it to autozone and scan it for free to find out

Sep 23, 2012 | 2006 Chevrolet Monte Carlo

1 Answer

How to remove the oil pressure sensor for a 2006 chrysler 300


how to change oil sensor on a chrylser 300 2006

Jun 09, 2012 | 2006 Chrysler 300

1 Answer

Replacement of the oil pan on a cadillac 2006 DTS


Big job.

gmlogoflat.gif Service Information
bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2006 Cadillac DTS ' DTS VIN K Service Manual ' Document ID: 636855 Oil Pan Removal

    1527739.gif
    tif.gif
  1. Rotate the engine so that the oil pan is facing up.
  2. Remove the oil pan drain plug.

  3. 1373472.gif
    tif.gif
  4. Remove the oil pan bolts.

  5. 1373475.gif
    tif.gif
  6. Remove the oil pan from the lower crankcase oil distribution manifold plate.

  7. 1373484.gif
    tif.gif
  8. Remove and discard the oil pan gasket.

  9. 204585.gif
    tif.gif
  10. Remove the oil level sensor (1).

Jul 29, 2011 | 2006 Cadillac DTS

1 Answer

I have a 2006 impala. On the highway the dinging wont go off on the oil light. It says oil pressure low turn off engine but I changed oil today. The dinging just wont stop!! What's wrong??


Hi stevie, your Impala probably has a defective sensor, often called a "switch" that senses the oil pressure. The oil light and chime is a result from a false signal from the bad sensor.
But one cannot take a chance. If the sensor is acting properly, and pressure is low, it could really damage your engine to have low oil pressure and oil not pumping properly. Have it checked now. A new sensor should cost about 60 dollars & takes only a few minutes to install.

Good luck. i hope this helps. Please rate me a FixYa.

Jul 01, 2011 | 2006 Chevrolet Impala

1 Answer

Where is oil sensor located in 2006 Audi a4 1.8?


There is a oil level sensor that is at the bottom of the engine oil pan. There is also an oil pressure switch that threads into the back of the engine block.

Jan 15, 2011 | 2006 Audi A4

2 Answers

2006 nissan quest is leaking oil from oil sensor how do I fix it


go to the parts store get one and rent a socket from them and change it it is easy they might lend you the socket if you buy the part from them

Oct 14, 2010 | 2006 Nissan Quest

1 Answer

Oil sensor replacement for 2006 GTO


COST Around $25 - $35 and Fallow these Instructions PLEASE RATE ME!!!!!

Engine Oil Pressure Sensor and/or Switch Replacement

Tools Required
  • J41712 Oil Pressure Switch Socket
Removal Procedure
Disconnect the oil pressure sensor electrical connector (1).
  1. Important: Clean the area around the sensor before removal. This prevents debris from entering the engine. Use J41712 to remove the oil pressure sensor from the engine block.
Installation Procedure
  1. If installing the old sensor, apply thread sealant GM P/N 12346004, (Canadian P/N 1093480), or equivalent. Notice: Refer to Fastener Notice in Service Precautions.
  2. Use to install the J41712 oil pressure sensor to the engine block. Tighten the engine oil pressure sensor to 35 Nm (26 ft. lbs.) .Connect the oil pressure sensor electrical connector (1).

Oct 04, 2009 | 2006 Pontiac GTO

1 Answer

What is oil sending unit on 2006 gmc sierra


if it shows low oil level its possible bad "level sensor "located on oil pan.if it shows low oil pressure possible oil "pressure sensor"

Sep 15, 2009 | 2006 GMC Sierra 1500 2WD

1 Answer

2006 Toyota Tacoma V6 engine oil sensor location


There is not enough flow at the sensor for a second oil filter. The sensor is at a dead end in the oil gallery. I recommend that you persue other options here. If you are concerned about oil contamination, don't be. There is nothing better than the factory filter...Look into adding more oil capacity; Look into an engine oil cooler; there is really no need for a second filter.

Sep 07, 2008 | 2006 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...