Question about 2001 Volkswagen Passat

Open Question

Gas pedal removal

How do you remove the gas and break petal?

Posted by on

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas petal not working


The linkage spring must be broken or the cable to the throttle body has broken. Check for broken cable at pedal end and throttle plate.

May 03, 2014 | 1990 Volkswagen Golf

2 Answers

Po300 & Po305 on a F-150


P0305 is cylinder #5 not firing. P0300 is random misfire which the computer cannot determine which cylinder(s) are misfiring. Check to This will make a lack of response or no power when the pedal is depressed. P0300 can be caused by spark plug wires needing replacement if equipped.

Mar 19, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

Brake booster from 1997 vw jetta removal instructions


Hi. Ther is a special tool for this, but it is clumsy and difficult. The plastic retainer is cheap enough to just break it out and fit a new one in place. fit it into the pedal first then clip the rod in otherwise the rod breaks through the clip before it seats into the pedal.

Jan 18, 2014 | 1997 Volkswagen Jetta

1 Answer

Brake pedal


Are you talking about the parking break? If the release won't work, gently press on the pedal with your foot will pulling on the release. At some point it should release.

Jan 05, 2014 | Cars & Trucks

1 Answer

1993 f350 460 cid wont start unless you press gas pedal to the floor


my truck starts right up if I hold the petal to the floor but wont start if I don't hold petal to floor

Feb 12, 2013 | 1993 Ford F350

1 Answer

How to install the gas cable to the petal


The cable end just goes into a slot at the back of the gas pedal, take a look you will see what i mean.

Sep 10, 2012 | 1995 Pontiac Trans Sport

1 Answer

Exceliator Petal sensor


The pedal sensor is part of the gas pedal. The whole thing needs to be replaced. Typically one connector and three nuts/bolts are all that need to be removed to replace it.

Mar 06, 2012 | Cars & Trucks

1 Answer

I am having a problem with the Acceleration, The petal may be loose? It feel like the petal doesn't go down as far as it used to, the cars takeoff is significantly slower now. I have inspected the gas...


Real good chance the throttle valve cable and linkage from throttle to top of linkage is seized, or seizing and needs lubrication. You'll have to remove battery to see it good under battery tray, and look for the piece of linkage on top where shifter linkage attaches.It needs to move freely. It also regulates your shift points as well, when passing etc. If you push gas pedal hard, it will begin to stick in lower gear longer (revving) before it shifts up, and will downshift hard as well when slowing to stop. Gas pedal will feel stiff, until you get it freed up. Try penetrating lube like WD-40 first to get it freed up, then spray white lithium grease or similar on it after. Do not try to remove nut holding it on, and remove linkage, just leave it on there and keep working it until it will move a full sweep back and forth freely. If you remove that piece of linkage, shaft will drop down and need to remove pan etc to fix it. If you need a picture, let me know, I have one from past experience with same.

Dec 15, 2010 | 1997 Dodge Neon

1 Answer

Once in a while the brake pedal will be low, normally after a 15 -20 highway ride! Seen when your usually getting of the highway!! This was first seen two month ago. Then after changing master cylinder I...


well all clues lead to the master but if you replaced it then that opens another can of worms...

when you push on your break petal a series of evens happen

the break boost assistants you in pressing the petal
the master cylinder plunger forces fluid around the break system and to each caliper/drum

you have to see if you got a re manufactured master ore a brand new one.. the problem sounds like the plunger in the master is allowiungnfluid to go past it.. faulty master,,,

the vibration in the break petal can only be 2 things...

warped rotors causing the caliper to osculate.. or theirs a steering component going bad

have a safty check done on your front end

Aug 10, 2009 | 2004 Dodge Caravan

2 Answers

3 inch bolt behind gas pedal


dont remove it if it did give you more power they wouldnt put it there keep it in place

Jul 23, 2009 | 1999 BMW 323 Series

Not finding what you are looking for?
2001 Volkswagen Passat Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...