Question about Cars & Trucks

1 Answer

Cylinder head bolt torque settings 1998 landrover freelander 2.0 t diesel

Posted by on

  •  adriaan de beer
    adriaan de beer Jul 12, 2013

    please ppl,help me its a landrover freelander 1998 model 2.0 turbo diesel,we redid the rings and all bearings and just need the head bolt torque settings how many nm and stages please

  •  adriaan de beer
    adriaan de beer Jul 13, 2013

    i need more help,anyone with the corect nm setings and the 3 stages

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 12,223 Answers

Go to www.automecanico.com and get the specification. Translate this amazing website with your browser and fix it.
God bless you

Posted on Jul 12, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: head bolts torque settings

According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Posted on Feb 07, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

junmag
  • 175 Answers

SOURCE: Blown head gasket

i think you are reffering to a 4D56 engine. just type 4D56 workshop manual .pdf download on your browser and you fill find several free downloads. everything you need to overhaul the engine is there

Posted on Jun 02, 2009

  • 15 Answers

SOURCE: replacement of cylinder head gasket freelander 1800 petrol

DEFINITELY NEW BOLTS.
1ST STAGE 20 NM
2ND STAGE 180 DEGREES
3RD STAGE 180 DEGREES.....JOB DONE.

Posted on Jul 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque settings for head bolts on Kia pregio 2001


What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Aug 17, 2015 | Kia Cars & Trucks

2 Answers

Heatbolt torque settings for audi 2.8 v6 30 valve quattro 1998 sedan


I assume you mean "Cylinder Head Bolts".

Tighten bolts in two-step sequence (See diagram)
Step 1 = 44 Ft. Lbs (60 N.m)
Step 2 = Additional 1/2 turn

These are "torque-to-yield" bolts and NEW bolts must ALWAYS be used when the cylinder head bolts are removed.


4_18_2012_11_18_43_pm.gif

Apr 18, 2012 | 1998 Audi A6

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

I would like the cylinder head torque setting for my landrover dicovery2 v8


Hope this helps you.

Cylinder head bolt's torque.

Engine with Suffix B, Cylinder head will have 10 bolt's.
Ft.lbs (N.m)
Step 1 - 15 ( 20 )
Step 2 - Additional 90 deg.
Step 3 - Additional 90 deg.

Engine without Suffix B, Cylinder haed will have 14 bolt's.
Ft.lbs (N.m)
Outer Row 44 (60)
Center Row 66 (90)
Inner Row 66 (90)


2ff67ca.gif28d5a83.gif

Sep 17, 2010 | 1995 Land Rover Discovery

1 Answer

I need to know what the cyl head torque and rocker arm torque is for a 1998 6.5 L GM turbo diesel.


Cylinder head bolts are done in 3 steps. Step 1 - 20 ft.-lbs
Step 2 - 50 ft.-lbs
Step 3: Tighten an additional
90 degrees.
Lifter guide plate bolts 18 ft-lbs
Rocker arm shaft bolts 40 ft-lbs
Hope this helps.

Aug 06, 2010 | 1999 GMC Sierra 3500

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

1 Answer

Cylinderhead bolts torque settings


According to my haynes manual for Landrover 200tdi, G - S reg,1989-1998 it goes as follows,
Stage 1:- Tighten all bolts to 30lb ft or 40Nm then
Stage 2:- Angle tighten a further 60 degrees then
Stage 3:- Angle tighten a further 60 degrees again.

Nov 29, 2008 | 1994 Land Rover Discovery

4 Answers

Head bolts torque settings


According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Oct 26, 2008 | 1995 Land Rover Discovery

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...