Question about Cars & Trucks

Open Question

Firing order 3.3L lamda engine 2007 santa fe limited

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: How to program keyless remote

I just had to buy one too and these are the instructions I was given by the guy I bought it from. I haven't tried them yet. Hopefully they work for us both :).

1.Find the ETACS unit under the steering wheel first,there is a small switch onit.
2.Once the switch is located make sure your key is not in the ignition and set the switch from off to set.
3.Press keyfobs door lock button for one second, this sends the codes to the ETACS and stores it.
4.Do the same thing if you have 2 remotes for the vehile.
5.Now set the ETACS switch from set to off.
6.Remotes should now be programed.

Posted on Jan 19, 2009

Ad
  • 1 Answer

SOURCE: 2007 Hyundai Santa Fe Limited

Hey all,
I was able to get installation instructions for the cross bars from http://www.capitolhyundai.com and from http://dealerfit.com.  Thanks much to these folks for providing a pdf of these instructions free of charge!
Below is the text from the instruction set that worked best for me.  The other instruction set was nearly identical but it had an alternate Step 2 which involved using a small plastic pry bar.  I added that alternate Step below in the instruction step.  Hopefully I'm able to insert the image of each instruction set so that the Figures are visible.  Its actually not that easy getting the rear rail covers off and its pretty easy to crack them.  I'd recommend gently rocking the covers for a couple minutes in order to loosen them up.  Once you get the covers off, the rest of the install is a breeze and can be done in 2 minutes.  If you have questions, go ahead and contact me.  I also took several photos of my install and that might be helpul.  Cheers!
-LePig
-----------------------------------------------------------------------
SANTA FE 2008 PIN U8210-28000 Cross Bar Assembly Installation Procedures
Kit Contents: • (2) Cross Bar Assemblies Required Tools: • Flat Head Screwdriver
INSTALLATION INSTRUCTIONS
1. Carefully unscrew and remove radio antenna. 2. Grasp the rear rail covers with both hands. Squeeze and pull up & inwards (toward the center of the vehicle) to remove covers. Take care not to break off the tabs by lifting the rear section of the cover first (Figure 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 2. - Alternate Method - Locate notch in rear of each cover to insert plastic pry bar.  Remove cover by prying up (with tool) and lifting rear at 45 degree angle (Fig 1). Be careful not to scratch, damage or dent any painted surfaces. DO NOT PRY AGAINST THE VEHICLE BODY, THIS CAN CAUSE DAMAGE TO THE VEHICLE. 3. Check assembly clips for damage and dislocation. Replace if necessary. 4. Open the lever on one side of front/rear cross bar. Gently set the cross bar, with the arrows facing forward, into the channel of the side rails (Figure 2). Guide both sides into the track. 5. To adjust cross bars, open lever and place cross bars in desired location. Close lever (Figure 3). Try to move bars forward/back until they lock into place. 6. Reinstall rear covers by holding cover at a 45 degree angle and inserting the front tab into the rear of the roof rack. After aligning, snap cover in place (Figure 4). Be sure that the rubber lip does not interfere with the covers, and that the covers are fully seated. 7. Reinstall the radio antenna. Note: To remove the cross bars, remove the antenna, remove the covers, open lever of cross bar and slide to end of rail. Hold down locking fingers (on both RH/LH rear rail supports) with a flat head screwdriver (Figure 5). This will allow removal of cross bars from the rails.

81e769d.jpg

Posted on Feb 24, 2009

goalie39
  • 469 Answers

SOURCE: ''check engine light'' illuminated, 1004 Hyundai, Santa Fe

If you live in the US, take it to qany Auto Zone store and thy will read the codes off for you, I would suspect any right thinking competitor would do the same, check if you don't have one near by.

Hope this is of some help.
Ed

Posted on Apr 21, 2009

dttech
  • 4803 Answers

SOURCE: How to change fuel filter 2007 Santa Fe Limited

The fuel filter on your vehicle is an integral part of the fuel pump/sender assembly located inside the fuel tank. It is serviced only as a complete assembly and cannot be replaced alone.

Posted on Dec 19, 2010

clifford224
  • 1975 Answers

SOURCE: Firing order 2005 v6 2.7

Here's a picture for you. Hope this helps and good luck.


clifford224_173.jpg

Posted on Mar 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse box diagram for 2007 hyundai santa fe


On this website you find fuse box diagram and description for Hyundai Santa Fe

Hyundai Santa Fe 2007 2009 fuse box diagram Auto Genius

Dec 23, 2012 | 2007 Hyundai Santa Fe Limited

1 Answer

The knob that secures the floor mat on drivers side is missing on my 2007 Hyundai Santa Fe. Can it be replaced?


Yes, definitely. Just go to your local hyundai dealer. if they do not have it in stock they will order in for you.

Mar 04, 2010 | 2007 Hyundai Santa Fe Limited

1 Answer

Location of oil filter on 2008 Santa Fe Limited


if it is a 3.3L it is a canister filter on top of the engine, the cover will need to be removed. make sure to change the o-rings. if it is a 2.7L, on bottom of engine near front of engine.

Apr 30, 2009 | 2007 Hyundai Santa Fe Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...