Question about 1995 Toyota Camry
This model often develops a noise from worn rear sway bar bracket bushings. They are inexpensive, so I would replace them and see if that was the problem.
Posted on Aug 04, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1. Look up along the lower radiator hose. It will plug into a metal
tube on the engine side. Follow the metal tube. It goes to a housing.
The housing is kind of buried in the driver's side of the engine. There
are 2 smaller coolant tubes plugged in above it. You do not need to
touch those, although it looks at first glance like you do.
2. Disconnect lower radiator hose at the metal tube.
3. Disconnect fan switches 1 and 2. These are on elecrtical harnesses going to this housing.
4. Disconnect a sensor on the front of the engine, just above the lower hose. I believe this is the knock sensor, but I'm not sure.
5. Now for the fun part. There are 3 bolts holding this housing on. You can see one at the top. There are 2 others underneath it, such that the bolts form a triangle pattern. You will have to get the bottom 2 out by feel (blind). They are 10mm.
6. Also, if you look to the front of the housing, you will note another 10mm bolt on the front holding down a black plastic leg. This is a wiring harness duct. Remove that bolt. Trace back along the duct. There is one more bolt on the driver's side retaining the duct. There is also one on the back of the engine at the firewall / driver's side. Remove these 2 as well.
7. There is a 12mm bolt holding the metal tube from that housing to the driver's side. Remove that bolt.
8. Gently pry the plastic wiring duct toward driver's side, and back toward firewall. You have just enough to get it off of the stud on the thermostat housing.
9. Now you can pull the housing. It will not come all the way out. It will come loose enough to give you just enough clearance to remove the thermostat (barely). Once you remove the thermostat, you have to pass it downward and toward the firewall to fumble it out.
By the way, you will notice that the metal tube is kind of wiggly in the thermostat housiung. This is normal.
10. Pass the new thermostat in the same way you got the old one out. Make sure when you plug it in that it has an air bleed poppet, and that this poppet is facing up.
11. Reassemble by reversing removal. Getting the nuts / bolts back in blind is... fun...
I don't know the torque spec. You can get a torqure wrench in there barely if you get creative with extensions, knuckles, etc. I wouldn't go abouve 8-10 ft-lb.
Posted on May 01, 2009
the camry has struts on the rear they have to be removed and put in a strut spring compressor to hold the spring then you can remove the top nut and replace the shock part of the strut
Posted on Jun 19, 2009
Have no idea the best one.They do exsist.Have you tried your local library? Or you can look on ebay.
Posted on Jan 02, 2010
Tips for a great answer:
Jun 18, 2016 | Nissan Cars & Trucks
Jun 24, 2014 | 1993 Lincoln Town Car
Dec 07, 2010 | Pontiac Grand Am Cars & Trucks
Sep 08, 2010 | 2000 GMC Jimmy
Aug 06, 2010 | 2002 Oldsmobile Intrigue
Oct 16, 2009 | 1994 Toyota Camry
Aug 19, 2009 | 1994 Toyota Tercel
Jun 29, 2009 | 1994 Toyota Celica
May 26, 2008 | 1997 BMW 318
90 people viewed this question
Usually answered in minutes!