Question about Cars & Trucks

Open Question

How to remove brake light fuse 2001 toyota mr2 spyder

Brake lights will not turn even when car is turned off. Where you locate and remove brake light fuse for 2001 toyota mr2 spyder

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 174 Answers

SOURCE: Brake lights stay on

check the brake light switch on the pedal

Posted on May 24, 2009

  • 1 Answer

SOURCE: Brake lights not working

Having the sa but haven't replaces the brake switch. The owner's manual for my 99 accord indicates the the fuse is located behind a panel that is viewable when you open the door on the driver's side. There is a panel that you remove (pull off) to expose the fuses. The brake light fuse is the third one from the top on the left. 7.5 A

Posted on Jun 16, 2009

keithheavili
  • 410 Answers

SOURCE: Brake lights refuse to turn off.

Your brake light switch is stuck. It is located on the brake pedal and they will do this sometimes. You can replace this part for relatively cheap and it doesn't take very long. The other option is to spray it with some WD-40 and try to work it out. Do one of these two things and you will be good to go. Let me know if you have any other questions. Thanks for rating my response and for using FixYa!

Posted on Jul 24, 2009

freelander72
  • 124 Answers

SOURCE: Tail Lights & Brake Lights stay on even when car is turn off

the plastic round stopper most probably broke that is were the stoplight switch sits when not depressed easy fix find a washer small enough to block the hole were the original plastic stopper was making sure the washer aligns to the brake light switch and secure washer w/ zipties hope this helps.

Posted on Aug 13, 2009

  • 484 Answers

SOURCE: 1989 Toyota Camry. No brake lights.

It could be the relay, which is a yellow box located under the carpeting in the trunk on the left side. It is a problem common to your model. Also, check the brake switch's (behind the brake pedal) functionality (12V present with key at ACC or ON and continuity between wires when button engaged).

i hope this helps
-matthew

Posted on Oct 26, 2009

Testimonial: "Wow! I would have never found the problem without you guys. It was the relay located in the trunk. Thanks!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My MR2 1986 hand brake light stays on can anyone tell me why


there is a contact switch that lights that light up when you raise your brake handle. down between the seats where it is located lots of debris settles, and more than likely, some of this has come between the contact point and switch and pushed the switch out of position. you need to remove the cover and the part you are looking for is at the end of the only electrical wires that connect to the brake assembly.remove obstruction and push contact up so that it turns the light off just as the lever is fully seated. then replace cover and your done.

Oct 29, 2011 | 1986 Toyota MR2

1 Answer

2001 MR2 emergency brake stuck, handle is limp, brake is stuck


well the cable is sized up you can try to put it in reverse that might fix it just because of the brake desinge but chances are you will have to have the emregency barke cables replaced

Dec 15, 2010 | 2001 Toyota MR2 Spyder

1 Answer

Hi I am having a few problems with my 2001 MR2 Spyder which i bought second hand about 6 months ago. I am being told I new a new engine by one mechanic and that it's just the rings by...


have you check the speed sensors? the check light wont be light if the sensor run off calibrate. try to visuallise the sensor if there is crack or something.

Nov 23, 2010 | 2001 Toyota MR2 Spyder

2 Answers

Cruise control in my 2003 mr2 spyder suddenly went out


check the fuse for the cruise control from the driver side located on the left side of the dashborad. Make sure the fuse is not blown out.
If it bad, change it out but make sure it is the same rated fuse.

Good luck

Jul 09, 2010 | 2003 Toyota MR2 Spyder

1 Answer

HOW DO I REPLACE A BRAKE LIGHT ON A 1987 MR2?


Open the rear bootlid behind the engine and there are two carpet panels on each side covering the light electrics. they are held in by fastners, push each fastner at the centre to release them.
Remove the carpet panel to get access to the brake light. Twist the bulb holder and replace the bulb.
Then replace the carpet panels using the fastners.

Nov 09, 2009 | 1987 Toyota MR2

1 Answer

How to replace headlight bulbs on 2001 MR2


The bulbs come out from behind the lamp assemblies, unplug the connector and turn it 1/4 turn.

Oct 05, 2008 | 2003 Toyota MR2 Spyder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...