Question about Cars & Trucks

Open Question

2006 dodge charger connecting rod bearing torque specification

2.7L engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 218 Answers

SOURCE: I need some torque specs for the connecting rod

20 FT LBS + A 1/4 TURN

Posted on May 04, 2009

terseo
  • 92 Answers

SOURCE: torque specs for 1998 tercel 1.5L

Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Posted on Sep 20, 2009

  • 33 Answers

SOURCE: what are the torque specs for main and rod bearing

go to autozone.com and set up a free account. You will then have access to vehicle repair guides and can get all the info and diagrams you need. Hope this helps!

Posted on Jan 02, 2010

AutoDoc
  • 169 Answers

SOURCE: tie rod replacement cost

Hi Gcg_77,
You will need to contact your local auto parts store to get price for the tie rod ends.My flat rate manual listed them at $65 a piece but this is an old price.
The labor time listed for these are as follows:

1 inner tie rod end is listed at 1.4 hours,if you replace both it is listed at 2.0 hours.
1 outer tie rod end is listed at 1.1 hours,if you replace both it is listed at 1.4 hours.
These times include resetting the toe only. If you want a complete alignment you deduct 0.4 hours labor and charge full alignment price.
Hope this helps. If you need anything else,let me know. Thanks,Chuck

Posted on Feb 11, 2010

drsinister69
  • 2317 Answers

SOURCE: What is the right Torque Specification of the

Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque for the main and rod bearings on a 2005 dodge stratus 2.7L automatic v6?


Main bearing cap bolts there is a outer cap bolt that are torqued to 20 ft lbs + 1/4 turn. Then there a inner cap bolt that are torqued to 15 ft lbs + 1/4 turn. Con rod bolts are torqued 20 ft lbs +1/4 turn

Jul 06, 2014 | 2006 Dodge Stratus

2 Answers

Engine connecting rod torque specification.


contact autozone or dealer service for specs..

Feb 09, 2013 | 2005 Suzuki Forenza

1 Answer

REPLACING CYLINDERHEAD-TORQU SPEXS NEEDED


For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of theconnecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90 more
4. Check that the crankshaft turns smoothly.

Sep 11, 2012 | Cars & Trucks

1 Answer

Torque specs for 1.5 kia rio connecting rod


TORQUE SPECIFICATIONS kia rio
Cylinder Head Bolts:
(21.7ft.lb) or (3.0kgf.m) 90?

May 22, 2010 | 2001 Kia Rio

1 Answer

What are the torque specs for the piston rods and head bolts


The connecting rod bearing cap nut on a four cylinder is 40 ft-lbs. The cylinder head bolts are torqued in four steps.1-45 ft-lbs 2-65 ft-lbs 3-65 ft-lbs 4 1/4 additional turn after reaching torque specification. On the V-6 & V-8 the connecting rod cap nuts at 45 ft-lbs and the headbolts are torqued in two steps 1-50 ft-lbs and 2-105 ft-lbs. Hope this will help you.

May 16, 2010 | 1995 Dodge Dakota

1 Answer

Need torque for a 2000 Toyota Celicia GT 1.8L


Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Mar 18, 2010 | 2000 Toyota Celica

1 Answer

Needing engine bolt torque specifications for a 2006 Ford Five Hundred with 3.0 liter engine. This will need to include rod and mains torque and torque rotation.


stage 1 tighten to 30 ft pounds
stage 2 tighten 90 degrees
stage 3 loosen one full turn
stage 4 tighten to 30 ft pounds
stage 5 tighten 90 degrees
stage 6 tighten 90 degrees
this is per mitchell on demand courtesy of ford specs on the lft and right head.
for some reason there are no torque specs on mitchell for connecting rods and mains.

Sep 15, 2009 | 2006 Ford Five Hundred

2 Answers

99 dodge intrepid specs


Inner main bearing cap bolts:
Torque to 15 ft-lbs, then rotate an additional 1/4 turn

Outer main (windage tray) bearing cap bolts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Main bearing cap cross bolts:
Torque to 250 in-lbs or 20.83 ft-lbs

Connecting road bearing cap nuts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Apr 21, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...