Question about Ford Cars & Trucks

Open Question

Ford p1441 - Ford Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1995 gmc jimmy. After service light came on, I had codes read. I had a smoke test done, lines were bad. I replaced them, had code cleared and light is back on!! Code is p1441. Any ideas or su


P1441 CHEVROLET Description The Engine Control Module (ECM) has detected vacuum flow to the Fuel Tank Pressure (FTP) sensor during a system sealed condition. Possible causes are a faulty canister purge solenoid or a faulty tank pressure sensor.

Read more: http://engine-codes.com/p1441_chevrolet.html#ixzz21ZntUMpS

Jul 24, 2012 | 1995 GMC Jimmy

1 Answer

Volkswagon Golf 1.9 tdi fault code P1441


Go here:

http://www.obd-codes.com/trouble_codes/volkswagen/

Jun 06, 2012 | Cars & Trucks

1 Answer

P1441


If you go to this site it lists the definition of this code by make, it also lists the possible causes of the problems that trigger the P1441 to be set in memory. Since you gave no specific info on the car or truck that is the best i can provide to help you diagnose this.

Feb 07, 2012 | Cars & Trucks

1 Answer

P1441 evap system flow during nonpurge


CODE P1441 -- EVAP SYSTEM FLOW DURING NON PURGE CONDITIONS. POSSIBLE CAUSES. EVAP PURGE VALVE PIPE OR THE CHARCOAL CANISTER HAS A TEMPORARY BLOCKAGE. FTP SENSOR IS OUT OF CALIBRATION DAMAGED OR IT IS SKEWED. EVAP PURGE SOLENOID VALVE IS DAMAGED OR HAS FAILED. PCM HAS FAILED.

Jul 06, 2011 | 1996 Buick Roadmaster

1 Answer

Imisions test comes back with, code P1441 ?


P1441 is a EVAP code, small leak I thinking.

P1441 Evaporative Emission (EVAP) System Flow During Non-Purge

Now for the fix: the ECM uses a pressure sensor to watch the system and see that there are no leaks. If it sees a leak via the pressure sensor, it sets this code. The ECM wants to see the pressure sensor voltage drop down, indicating that there is vacuum on the system, and it wants it to be able to hold this vacuum for at least 30 seconds. If this does not happen, it will set a code. As a note, the vent solenoid is the most common failure on these systems.

Hope helps (remember to rate and comment this).

Sep 22, 2010 | 1996 Buick Riviera

3 Answers

Where is the purge solenoid location on a 1996 Chevrolet silverado 1500 ???? trucks runs bad and I was told it was that or some other vacuum leak also I have code p0300 and p1441 if anyone can help...


A P0300 DTC is a misfire code. The P1441 is a no flow during purge code which has to do with the purge solenoid. With the misfire code present I would say you have a vacuum leak on one of the hoses. The purge solenoid is located in the passenger side, rear of the intake manifold.

May 09, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

P1441 PROBLEM WITH MY BUICK PARK AVENUE 1997


P1441 Evaporative Emission (EVAP) System Flow During Non-Purge
The evap system is your egr valve, carbon canister, pcv valve, gas cap, and fuel tank vent, The most common fix for this problem is a new gas cap and then your done. It is about 15 dollars and then you pass smog. If this has been of any help please reate. Thank you

Feb 12, 2009 | 1996 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...