Question about Peugeot Cars & Trucks

Open Question

1351 code peugeot 607 2.2hdi

Limp home comes on

Posted by Anonymous on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1619 Answers

SOURCE: fault code 1351 loss of power under load

Check engine wiring harness for degradation as from 1993-1995 MB was forced to use biodegradable insulation on its wiring. The throttle actuator is suseptable to it also.

Posted on Apr 18, 2010

  • 749 Answers

SOURCE: 2005 Chevrolet Cobalt in "limp home mode" code 606

P0606 indicates Control module internal performance. GM is indicating of the replacement ECM. Once replacement is completed reprogramming the ecm is necessary. Locally a few auot parts stores can reflash the ECM.May want to check with a NAPA or Carquest for this otherwise dealer is probably the only option.

  • Using a scan tool, retrieve the percentage of remaining engine oil. Record the remaining engine oil life.
  • Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  • jsmes1027_30.gif
  • Disconnect the small engine control module (ECM) harness connector (3) from the ECM.
  • Remove the bolt retaining the large ECM connector to the ECM.
  • Disconnect the large ECM harness connector (4) from the ECM.
  • jsmes1027_31.gif
    Notice: Control module damage may result when the metal case contacts battery voltage. DO NOT contact the control module metal case with battery voltage when servicing a control module, using battery booster cables or when charging the vehicles battery.
  • Use the retaining tab to release the ECM from the underhood junction block bracket.

  • Reverse process for installation

    Posted on Dec 11, 2010

    • 80637 Answers

    SOURCE: How do I fix code p1191 eta limp home valve on.

    P1193 - EGR Drive Overcurrent

    Posted on Sep 13, 2012

    Add Your Answer

    Uploading: 0%


    Complete. Click "Add" to insert your video. Add



    Related Questions:

    1 Answer

    Peugeot 407 2.0 HDI starts an stops immediately

    Seat belt sensor. Get it checked.

    Jan 01, 2018 | Cars & Trucks

    2 Answers

    I have an 09 Peugeot 308 petrol. the fan kicked in and I got a faulty anti pollution msg even tho engine was cold Any ideas?

    You need to scan the engine management computer and read the fault codes. Based on that info you can begin the diagnosis and repair.

    May 23, 2016 | Peugeot Cars & Trucks

    1 Answer

    My peugeot 206 model doesn't have revs whats the problem?

    could be in limp mode
    run the fault codes to see what is reported

    May 07, 2016 | 2005 Peugeot 206 1.4

    2 Answers

    Stuck in limp mode

    Limp Mode is usually a transmission failure
    that will have to be diagnosed-check for codes
    & google what they are

    There are overheating & possibly other limp
    modes on some vehicles

    Can't use it at all like that & not cause a problem

    Need a repair shop or dealer

    Jun 10, 2014 | 2001 Peugeot 206 1.6

    1 Answer

    307 peugeot

    sensor failed or failing and ecu is in limp mode. you need to have the ecu read to find the fault as it can be one of many sensors cam/ crank, egr etc fault can trigger then the fault is gone but ecu will still be in limp mode. can take upto 30 starts to remove fault code and be out of limp mode.

    Jan 16, 2018 | Cars & Trucks

    1 Answer

    My 2004 Xg350 is stuck in limp home mode.

    code p1155 refers to electronic throttle system (ETS)- malfunction===causes --wiring--ETS limp home valve

    code p1193 refers to ETS -limp home valve --on===causes --Low RPM
    code p0302 refers to cylinder 2 misfire detected===causes--engine mechanical fault--wiring---ignition/ fuel system---injector---ECT/MAF sensor---ECM.
    Pulling a battery lead to reset is a waste of time as it corrupts the CPU program. Use a code reader to reset . It is quicker and doesn't run the risk of program corruption

    Dec 21, 2013 | Hyundai XG350 Cars & Trucks

    1 Answer

    Citroen relay 2.2 van when driving little red engine sign comes on and the power drops

    this is the engine light and the CPU goes to limp mode to protect the engine/gearbox. Check oil and coolant levels and run fault codes to detect which sensor put the light on.

    Dec 10, 2013 | 2005 Peugeot 405

    1 Answer

    Vehicle misfire... diagnostic code is 1351

    Code 1351 is for the ignition control module.Ignition control circuit high.This module is on the same bracket as the coil.Before you buy a new one.Try a salvage yard and get a used one.

    Nov 19, 2009 | 1997 GMC Sierra

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    65 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Peugeot Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    mike hayward

    Level 2 Expert

    279 Answers

    Wahs Team

    Level 2 Expert

    215 Answers

    Are you a Peugeot Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides