Question about 2001 Chrysler Town & Country

1 Answer

Weather striping Around the rear window wiper motor shaft on the out side of window is a round rubber weather strip on my 2001 Chrysler town and country. What is it called and where can I find one so I can replace it ? Maybe you have OEM part number ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 288 Answers

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75066 Answers

SOURCE: i have a problem with power sliding doors on 2001 Chrysler Town and Country limited

do you mean they are sticking?

Posted on Oct 20, 2008

keemo68
  • 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

c17hydro
  • 2984 Answers

SOURCE: my 2001 Town and Country's rear windshield wiper

Pretty straight forward.....here are the steps:

Please don't forget to rate--

Rear Window Wiper Motor Removal & Installation To Remove:

  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear wiper arm.
  3. Open the liftgate.
  4. Perform the following to remove the liftgate trim panel.
    • If equipped, remove the lift motor link
    • Remove the upper frame molding
    • Remove assist handle screws
    • Disengage the hidden clips around perimeter of liftgate trim
    • Disconnect the electrical connectors.
  5. Disconnect the wire connector from the wiper motor.
  6. Remove the wiper motor mounting screws.
  7. Remove the wiper motor.
To Install:
  1. Position the wiper motor in the liftgate.
  2. Install the wiper motor mounting screws.
  3. Connect the wiring connector.
  4. Install the liftgate trim panel.
  5. Close the liftgate.

Posted on Jul 24, 2009

  • 39 Answers

SOURCE: passenger window and rear vent window stopped working

YOU PROBABALY MAVE A BROKEN WIRE IN THE HARNESS THAT GOES FROM THE DRIVERS DOOR TO THE INSIDE OF THE VEHICLE

Posted on Jul 24, 2009

  • 5 Answers

SOURCE: 2001 Chrysler Town and Country Window problem.

it could possably be the motors for the windows are bad

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 town and country and the wipers will not turn off with the car turned off and i cant change the speed of them either


The wiper module is built into the the wiper motor. First unplug it(on the drivers side, just under the wiper cowling) Look for corrosion. Clean it with battery cleaner, the plug and motor connector. If it still acts up. replace the wiper motor.

Sep 01, 2015 | 2001 Chrysler Town & Country

2 Answers

How to repair back window


If mean how to tint the rear window, The tint goes on the inside. I would remove the plastic rear door cover to start with because you will already be working over your head, after that thoroughly cleaning window with a vinegar based window cleaner, cut film at least 2 inches extra on each side (4 inches added to the widest and tallest measurement) spray water onto window with spray bottle, center film start in center with soft rubber squeegee pushing water and air bubbles out while leaving all 4 sides loose so more water can be sprayed onto window as you work your way out trim excess tint off with razor re-install door panel.

May 11, 2014 | 2006 Chrysler Town & Country

2 Answers

I have one wiper that does not work the other stops in the middle of the windshield how can i fix them


The motor could be bad, but it's likely that the ball joint connections under the hood area under the cowl have become disconnected for the one windshield wiper arm.

The connection of the arm that moves should be checked for being at the correct angle for parking.
Removal & Installation 2000-03 Wiper Motor and Bushing Replacement L4-2.2L (Vin F) & V6-3.0L (Vin R) To Remove:
sat_car_22_fw-wpr_arm_xp.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Remove the wiper arm finish caps
  3. Mark both wiper arm positions on the windshield by using a wax pencil or tape
  4. Remove or disconnect the following:
    • Wiper arm retaining nuts and washers
    • Wiper arms
    • Weather-strip at rear of hood sat_car_22_f_wshd_wthr-strp.gif

      sat_car_22_f_wshd_gril_nts.gif

    • Grill nuts from base of wiper arm shaft
    • Grill
    • Electrical harness connector from the wiper motor
    • Wiper motor retaining bolts
    • Wiper motor assembly from plenum area
    sat_car_22_f_wpr-mtr_asy.gif

    sat_car_19_wpr_mdl_rmv.gif

  5. If replacing wiper module bushings remove the steel bushing first then the rubber grommet
  6. Remove the wiper motor from the transmission assembly
To Install:
  1. Install or connect the following:
    • Wiper motor to transmission assembly NOTE: If the wiper module bushings were replaced install the rubber grommet first then the steel bushing.
    • Wiper motor to plenum area
    • Wiper motor retaining bolts; torque to 44 lb-in. (5 Nm)
    • Electrical harness connector to the wiper motor
    • Weather-strip at the rear of hood
    • Grill
    • Grill nuts to the base of the wiper arm shaft
  2. Install the wiper arm assemblies at the marks made during removal or at the PARK position if a new wiper motor is installed
  3. Install the wiper arm retaining washers and nuts; torque to 9 lb-ft. (12 Nm)
  4. Install the wiper arm finish caps
  5. Verify correct wiper system operation
prev.gif next.gif

Oct 05, 2010 | 2001 Saturn L-Series

1 Answer

My Chrysler Town and Country back wiper has been replaced but now the wiper moves but doesn't fully mold to the window.


WIPER ARM IS NOT IN RELATION WITH WIPER MOTOR SHAFT.THATS WHY NOT FULLY MOLD TO WINDOW.

Jul 03, 2010 | Cars & Trucks

1 Answer

How do i get the rear wiper arm off a 2000 chrysler town n country...im replacing the motor


Look at the wiper arm. Where the shaft comes through there is a cap on the arm. Pop it up and you will see a nut remove nut and you should be able to get arm off.
Hope that helps!

Mar 06, 2010 | 2000 Chrysler Town & Country

2 Answers

One wiper not working.


if you can move the arm while the wipers are parked, either the linkage popped off or the arm came off the splines. take the cover off where the nut is and see if the arm moves on the shaft, this usually happens when you turn the wipers on and they are frozen, and crank the nut down. I usually put some thread lock on them first.

Dec 31, 2009 | 2001 Chrysler Town & Country

1 Answer

My 2001 Town and Country's rear windshield wiper motor is kaput. How do I change it without destroying the rear tailgate paneling


Pretty straight forward.....here are the steps:

Please don't forget to rate--

Rear Window Wiper Motor Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear wiper arm.
  3. Open the liftgate.
  4. Perform the following to remove the liftgate trim panel.
    • If equipped, remove the lift motor link
    • Remove the upper frame molding
    • Remove assist handle screws
    • Disengage the hidden clips around perimeter of liftgate trim
    • Disconnect the electrical connectors.
  5. Disconnect the wire connector from the wiper motor.
  6. Remove the wiper motor mounting screws.
  7. Remove the wiper motor.
To Install:
  1. Position the wiper motor in the liftgate.
  2. Install the wiper motor mounting screws.
  3. Connect the wiring connector.
  4. Install the liftgate trim panel.
  5. Close the liftgate.

Jul 24, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2001 Chrysler Town & Country Logo

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...