Question about 2003 Ford ZX2

Open Question

2003 ford zx2 abs control module

Location of abs control module

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: location of ignition control module

It does not have an ignition control module.
The electronic ignition (EI) for the 4.0L engine consists of the following components:
Crankshaft position sensor (CKP sensor) and 36 minus 1 tooth trigger wheel.
Ignition coil .
powertrain control module (PCM) .
Related wiring.
The PCM controls the firing of the coil based on the signal from the crankshaft position sensor.
The crankshaft position sensor (CKP sensor) is a variable reluctance-type sensor, triggered by a 36 minus 1 tooth trigger wheel configuration machined into the rear of the crankshaft vibration damper. The signal generated by this CKP sensor is called a CKP signal. The CKP signal provides the base timing and rpm information to the powertrain control module (PCM). Base timing is set at 10 degrees BTDC and is not adjustable.
If vehicle has no spark then turn key to on position,check engine light should come on.As you start cranking engine it should go out while cranking after about 10 secs. it should come back on(while cranking). If it come on then the PCM sees the signal,if it does not then PCM is not seeing it and this is your problem,either the CKP sensor or the wiring to it.

Posted on Mar 16, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

  • 1 Answer

SOURCE: Ford 2003 ZX2 Blower does not work need fuse diagram

The fuse box is under the dash on the drivers side, the cover for it has a map showing which amperage fuse goes to what, includes the three most common sizes in the cover and a little plastic tool to remove them...hope this helps

Posted on Jun 20, 2009

  • 20 Answers

SOURCE: ford focus has the ABS brake light on and traction control light

chek the brake fliud level. if low light will set light and abs wont work.

Posted on Apr 25, 2010

ZX2Fast
  • 547 Answers

SOURCE: location of the airbag sensor and control module

There is no separate sensor. The airbag module has an inertia sensor that determines if the airbag is deployed. The module is in the center of the dash area, mounted to the floor. You'll have to look behind the heater core box to see it.

Posted on Nov 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford escort zx2 abs module location ? And is it hard to get off ?


The average vehicle's abs module is located on the firewall and is fairly difficult to remove. Double check if your car is equipped abs as zx2's rarely are.

Mar 18, 2014 | Cars & Trucks

1 Answer

Where is ccrm located on 98 escort zx2 located


The Constant Control Relay Module is located right underneath the air cleaner box. Please be sure to replace it with the correct module, they are not the same. Use all the numbers on the old one, like F8CZ-12B577-AA, AB, AC, there are others.

Jul 11, 2012 | 1998 Ford Escort

1 Answer

Service engine light came on the code is P1751. where is shift selenoid located on 2003 ford zx2


All of the shift solenoids are located inside the transmission attached to the hydraulic control valve body, to access them you must remove the pan located on the bottom of the transmission.

Oct 28, 2011 | 2003 Ford ZX2

2 Answers

Idles rough in drive,runs good on open road,noticed while idleing if i open oil fill cap if goes pufffffff like relieving pressure,should it build pressure in the motor like that,i put new plug wires,new...


All automatic ZX2's have a rough idle in gear. Ford even put out a TSB and tried to fix it with no success. The engine is internally balanced and does not have a harmonic dampener. This means you get all of the engine vibration transferred to the frame. I own three ZX2's, my sister has one, my friend has two, they all have rough idle in drive.

The noise you get from the oil filler is normal to an extent. It is an overhead cam engine so you will hear noise from the oil filler. The oil you see on the spark plugs is likely from the valve cover gasket. That is the only place the oil can come from and get onto the top of the spark plugs. It can't travel through the spark plug threads and get on top from the combustion chamber.

It is good you replaced the PCV valve (I know it is hard to reach) but did you replace the breather? There is a round black box with a hose coming from the intake that goes onto the top of the valve cover. This is the air inlet for the PCV and if it gets clogged it will allow pressure to build up in the crank case.

Mar 04, 2011 | 2003 Ford ZX2

2 Answers

2005 Ford Tarus. Where is the ABS Module located ? Is it difficult to replace?


Why would you replace an ABS Module
on a vehicle, only 5 years old?

The module !!
The Controller !!

Feb 22, 2011 | 2005 Ford Taurus

3 Answers

Where is it located ABS Module 2000 Expidition


Where do u unplug abs module on 2000 ford expedition

Dec 15, 2010 | 2000 Ford Expedition

1 Answer

Location of the airbag sensor and control module on ford escort zx2


There is no separate sensor. The airbag module has an inertia sensor that determines if the airbag is deployed. The module is in the center of the dash area, mounted to the floor. You'll have to look behind the heater core box to see it.

Oct 15, 2010 | 2001 Ford Escort ZX2

1 Answer

Where is the idle air control sensorm located at on a 2003 ford escort zx2


it should be located on or in close proximity to the throtle body.

Feb 14, 2010 | 2001 Ford Escort ZX2

1 Answer

Where is the idle air control sensor locatyed at on a 2003 ford escort zx2


The idle air control vavle is located on the driver side of the intake manifold, below the throttle body. You'll have to remove the air intake to see it. It is held there by two bolts.

Feb 14, 2010 | 2001 Ford Escort ZX2

2 Answers

Ford 2003 ZX2 Blower does not work need fuse diagram


The fuse box is under the dash on the drivers side, the cover for it has a map showing which amperage fuse goes to what, includes the three most common sizes in the cover and a little plastic tool to remove them...hope this helps

Dec 22, 2008 | 2003 Ford ZX2

Not finding what you are looking for?
2003 Ford ZX2 Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...