Question about 2005 Nissan Altima

Open Question

BCM nissan altima - 2005 Nissan Altima

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the passenger side low beam fuse located on a 2006 Nissan Altima


Low Beam Operation With the lighting switch in 2ND position, the BCM receives input requesting the headlamps to illuminate. This input is communicated to the IPDM E/R across the CAN communication lines. The CPU of the IPDM E/R controls the headlamp low relay coil. When energized, this relay directs power ? through 15A fuse (No. 36, located in the IPDM E/R) ? through IPDM E/R terminal 20 ? to headlamp RH terminal 1, and ? through 15A fuse (No. 45, located in the IPDM E/R) ? through IPDM E/R terminal 30 ? to headlamp LH terminal 1. Ground is supplied ? to headlamp RH terminal 2 ? to headlamp LH terminal 2 ? through grounds E15 and E24. With power and ground supplied, low beam headlamps illuminate.

IPDM E/R - fuse box E/R -- engine room , under hood fuse box .

System Description EKS008LH Control of the headlamp system operation is dependent upon the position of the combination switch (lighting switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input requesting the headlamps (and tail lamps) to illuminate. This input is communicated to the IPDM E/R (intelligent power distribution module engine room) across the CAN communication lines. The CPU (central processing unit) of the IPDM E/R controls the headlamp high and headlamp low relay coils. When energized, these relays direct power to the respective headlamps, which then illuminate. OUTLINE Power is supplied at all times ? to headlamp high relay, located in the IPDM E/R, and ? to headlamp low relay, located in the IPDM E/R, and ? through 50A fusible link (letter f , located in the fuse and fusible link box) ? to BCM terminal 70. With the ignition switch in the ON or START position, power is supplied ? through 10A fuse [No. 1, located in the fuse block (J/B)] ? to BCM terminal 38. With the ignition switch in the ACC or ON position, power is supplied ? through 10A fuse [No. 6, located in the fuse block (J/B)] ? to BCM terminal 11. Ground is supplied

https://carmanuals2.com/brand/nissan/altima-2006-4924

May 05, 2017 | Nissan Cars & Trucks

1 Answer

I own a 2005 nissan altima. Is there any way to remove the kill switch. It is causing my car not to start


Sorry, there isn't. It needs to be scanned for codes. This will point you in a direction to look at. Could be the key, receiver, wiring, BCM, and PCM.

Apr 17, 2015 | 2005 Nissan Altima

1 Answer

2009 Altima, 2.5. We recently had the BCM and radio replaced, transmission control module reprogrammed, engine torque rods and buffer assembly replaced by Nissan under an extended warranty. After getting...


Sorry to tell you this, but neither of those computers would require any work on the HVAC case. The BCM is located above the instrument cluster. The TCM is located under the hood [which is a very poor location] I'm a 35 year professional mechanic. Sorry to tell you this, but my opinion of the Altima is very poor. These things have all sorts of problems, are hard to work on and the parts are very expensive. Lots of recalls and TSBs [technical service bulletins] TSB is dealer speak for "oops, we goofed". You can't blame the dealer for this one.

Dec 03, 2014 | 2009 Nissan Altima 2.5

1 Answer

2002 Altima cranks no start. Dealer said that the bcm ecm and immobilizer all need to be replaced. Had to come up witht he money so I had the car towed back to house. Now the dealer is saying that the dash...


Did your Check Engine or Service Engine Soon light come on? If so, did you read the code stored in the ECM? If so, what was (were) the code(s). It's unlikely that the ECM and BCM would both completely fail at the same time. More info please.

Oct 03, 2013 | 2002 Nissan Altima

1 Answer

The moonroof on my 98 nissan altima doesn't work


Skylight itself damage, BCM control unit fault, the line problem, sunroof motor does not work and so on all may cause skylight switch failure
auto diagnostic tool

Apr 04, 2013 | Cars & Trucks

1 Answer

What is wrong with my 2005 nissan altima when gear is stuck in park.


If all the fuses are good, then you probably have one of the following conditions... The wire that leads from the brake switch to the BCM to tell it that your foot it on the brake has severed, and thus it won't unlock the shifter. Or, the signal could be fine, but the actual solenoid that mechanically unlocks the shifter may have failed.

Either way, if you are handy with a multimeter and have a service manual, you will be able to troubleshoot your fault without seeing a dealer - but since it's under warranty, you might as well bring it in.

Jan 12, 2012 | 2005 Nissan Altima

3 Answers

2005 NISSAN ALTIMA 2.5S THE TRUNK RELEASE BUTTON DOESN'T OPEN THE TRUNK,ANY IDEA WHY?


check in your glove box on left hand side.valet switch may have accidentally set.let me know how you make out!

Feb 12, 2011 | 2005 Nissan Altima

2 Answers

2003 Altima radio stays on after removing keys from ignition


It very well could be the BCM....only way to check it is to have a full featured scan tool, and check out the systems.

Sep 30, 2009 | 2003 Nissan Altima

1 Answer

THE AUTO DOOR LOCK AND POWER WINDOW DO NOT WORK AND I CANT FIND THE FUSE FOR THEM ON 2005 NISSAN ALTIMA


From the service manual, which is available relatively inexpensive at Promanuals.net here

 Both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room)
 Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
Terminal combination status is read by BCM (body control module)
 BCM controls front wiper LO, HI, and INT (intermittent) operation
 IPDM E/R operates the wiper motor according to CAN communication signals from the BCM.
Power is supplied at all times
 through 50A fusible link (letter f , located in the fuse and fusible link box)
 to BCM terminal 70, and
 through 20A fuse (No. 39, located in the IPDM E/R)
 to front wiper relay, located in the IPDM E/R
With the ignition switch in ON or START position, power is supplied at all times
 through 10A fuse [No. 1, located in the fuse block (J/B)]

Sep 28, 2009 | 2005 Nissan Altima

Not finding what you are looking for?
2005 Nissan Altima Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...