Question about Cars & Trucks

Open Question

Headlight replacement 1990 Mitsubishi L300 van

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: heater wont blow hot air in van. How do i fix it?

add coolant to the radiator and it should help circulate it and warm the air up

Posted on May 07, 2009

Ad
  • 1986 Answers

SOURCE: i want to adjust the headlight height

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 13, 2009

  • 104 Answers

SOURCE: where is the engine number on a 1990 l300

If u give the VIN number to a parts place they can give u the engine code

Posted on Oct 21, 2009

Testimonial: "fast and honest. thanks"

  • 1011 Answers

SOURCE: my Mitsubishi l300 van wont go in to fourth gear

check gear linkage

Posted on Mar 03, 2010

  • 180 Answers

SOURCE: i want to know the liter capacity of my fuel tank

the capacity of the tank is 55 litres

Posted on Apr 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My l300 van when i open/flash the headlight the engine will stop, but when i start it will start again.


One of the fuses may have gone bad i recamend going to your mecanic and have them chesk it out

Apr 11, 2012 | Mitsubishi Cars & Trucks

1 Answer

Couple of days ago my van mitsubishi l300 1990 did not start.battery ws old so thought it had died, jump start didnt help. put a new battery on today, started for 2sec and then died out, pushing accel did...


do you have a diesel or gas engine? if its gas most likely you have a grounded ignition wiring. the short may be intermittent thus it starts then stalls when the voltage supply to the ignition coil is disrupted when the wire gets in contact with earth

Jun 25, 2011 | 1990 Mitsubishi Minivan

1 Answer

Where is the master brake cylinder located on a 1988 mitsubishi L300 van?


If it's like the 1995, it's behind the dash. The brake booster is behind the master cylinder, on top of the pedal box. You have to drop the steering wheel and pull the dash off to get access. Even then it's extremely difficult to do anything.

Apr 14, 2011 | 1990 Mitsubishi Minivan

1 Answer

My L300 versa van 2.5 gas engine consumes 6kilometers per liter. is it normal for that size of engine? what should i do.


Absolutely not! It probably has a fuel metering problem. I would definetly take it to a local mecanic to have it checked out.

Dec 08, 2010 | 1990 Mitsubishi Minivan

1 Answer

Misubishi L300 sliding door


Any year door between 1979 and present will do, the basic shell of the car - including doors - hasn't changed.
For a perfect fit of the trim you should get one from 79 to 86.

Jun 04, 2010 | Mitsubishi Cargo Cars & Trucks

1 Answer

Loose Steering linkage on '85 L300 swb van


its a 85 its probley time for new joints and the gear box is probley kinda beat to

Mar 20, 2009 | 1990 Mitsubishi Minivan

1 Answer

In my L300 (van) I have almost no pressure to rear brakes. Have replaced master cylinder, apportioning valves, brake cylinders, shoes... lines look fine. Bled them to death. Can't understand whats going...


load sensing valve link between rear axle and body is out of adjustment. best way to fix is adjust in direction of downward body movement causes valve to open more. a 12mm spanner is all you need.

Sep 30, 2008 | 1990 Mitsubishi Minivan

1 Answer

L300 express van/ starter motor


http://www.alldatadiy.com will cover your vehicle completely. However, there is a subscription fee; $21 for the first vehicle and $16 for each additional vehicle for a year subscription. Or, you could send a text from your cell phone to Cha Cha, (242-242) and ask them. It is free and only costs whatever it normally costs you to send a text from your cell phone. They can answer ANY question. Real people. Not computers like Google.

Aug 19, 2008 | 1990 Mitsubishi Minivan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...