Question about Cars & Trucks

Open Question

Search Fixya...oil drain plug size for 2010 dodge journey

Size of socket needed to undo the oil plug in a 2010 dodge journey

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: oil change

Hi
see my previous post "oil filters" which basically the same as this
there is a special tool for removing the oil filter "plastic cover " - (a 14 flute 76mm cap type) & this is a "must have " or the cover can be damaged 17mm spanner/socket, 6 mm allen key for the drain in filter housing along with the new filter cartrdge you should also get the 2 "o" rings as well. there is website that Robert Aitchision hs put up which gives a complete description of how to do it with pics & what is needed.
Thanks Robert
http://robert.aitchison.org/tiki-page.php?pageName=Mazda3+DIY+Oil+Change

Can get the filter tool &/or spin-on filter conversion from - see link below
http://www.mazdastuff.com/directory.cfm?CategoryID=242

Posted on Apr 09, 2009

Ad
cadman000
  • 607 Answers

SOURCE: changing the oil by myself for the 1st time what size socket

Try a14 mm

Posted on Apr 10, 2009

buffalonyman
  • 1865 Answers

SOURCE: changing the oil

The drain plug is on the oil pan, bottom of engine. Use an adjustable wrench

Posted on May 15, 2009

  • 9 Answers

SOURCE: what size socket do I need to change the oil and brakes.

The oil drain plug is a 13 mm. The tools for the brakes, a 10 mm socket for the caliper pins, a flat head screwdriver, or a meduim size prybat to get the calipers out of the mounting bracket, and a 4" C-clamp to compress the pistons into the calipers so you can put the new pads on.

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is engine oil drain plug om holden viva


Hi Steven engine oil drain plug will be on the lower most part of the sump. It will be either a bolt type plug which you undo with a spanner or it will be a flat type plug which has a thickness of a coin. If its this type there will be a small hole in the centre and a Torx bit will be needed to undo this plug. This Torx plug be very careful when undoing it do not let it slip around in the hole. Make sure you have the right size bit DO NOT use a size smaller. It has to be a tight fit. Support the socket in the hole with the palm of your hand with pressure whilst turning the bar (preferable) 12 inch or slightly longer or ratchet attached to the Torx bit. anti clockwise to undo clockwise to tighten. There will be a sealing washer on the bolt type and a rubber o ring on the coin type these have to be replaced on refitting. I advise the coin type you fit a new plug as well, as the grip for the Torx plug tends to wear. If for any reason you feel this Torx socket starts to slip stop at this point (this is common). Book into Holden's as care and experience is going to be needed to remove it with as little damage as possible. Good luck

Dec 31, 2017 | Holden Cars & Trucks

1 Answer

Where is camshaft sensor located on 2010 dodge journey?


here is a link that will show you a diagram for the 2010 Dodge Journey 4Cyl.

I hope this helps

http://engine-codes.com/qa/17736/location-of-crankshaft-sensor

Apr 26, 2015 | 2010 Dodge Journey

1 Answer

I'm a woman trying to teach myself how to maintain my own car. I have a 2009 Dodge Journey 3.5 v6. I wanted to know basic instructions on how to change the oil myself? any help pls?


You could try some YouTube videos on similar models.
Its a messy job, and for most people easier to pay someone to do.
You have to remove the drain plug from the oil pan to drain the oil into a pan, then dispose of it safely, and change the filter, then refill the oil pan with new oil.

Sep 28, 2012 | 2009 Dodge Journey

1 Answer

What size socket do I need to change the oil and brakes.


The oil drain plug is a 13 mm. The tools for the brakes, a 10 mm socket for the caliper pins, a flat head screwdriver, or a meduim size prybat to get the calipers out of the mounting bracket, and a 4" C-clamp to compress the pistons into the calipers so you can put the new pads on.

Sep 15, 2009 | Dodge Neon Cars & Trucks

1 Answer

Changing the oil


The drain plug is on the oil pan, bottom of engine. Use an adjustable wrench

May 03, 2009 | 2002 Dodge Stratus

1 Answer

Honda accord 1991 oil change


You are referring to the drain bolt on the oil pan? You can use a crescent wrench. I have a 92 and I can never remember what size the drain bolt is, so I always go under with my trusty adjustable crescent wrench. Let me know if u need more info.

Nov 11, 2008 | 1992 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15427 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...