Question about Porsche Cars & Trucks

Open Question

Porsche faults 911 996 fault code 5525

ABS Light on dash & PSM light on dash fault code 5525

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: fault code 0562.oil level sensor

You have two sensors that could cause the light to go on. The oil pressure sensor and oil level sensor. Both are easily replaced by someone relatively OK with cars (DIY). You would want to spend the $100 or so and have the dealership do a full diognostic to verify if its truly the sensor and which one. In my case, same problem, and it has been verified that it was the oil level sensor.

Posted on Aug 30, 2008

SOURCE: mazda tribute abs fault. abs

These vehicles have a recall on the ABS system for faulty wiring. You may want to check with your local dealer to see if your vehicle is included.

Posted on Sep 20, 2008

tripletauto
  • 1450 Answers

SOURCE: shows ABS fault on dash and ABS light stays on

Check your abs connectors they might have pulled a wire loose

Posted on Nov 11, 2008

  • 44 Answers

SOURCE: XK8 ABS FAULT LIGHT COMES ON INTERMITANTLY PLUS

Number of possibilities. Most likely culprit is wheel bearings. Have these checked. Big heavy car and wheel bearings do take a hammering on XK and XJ's. Once they go, the wheel speed sensors are out of line with the tracking ring and a fault code is thrown. As the TCS uses the same sensor, this also throws a fault. Next in line is the ABS unit (it's hardly ever the main block, but ECU itself, companies on the net offer rebuilt units. Finally it can be the ABS pump unit - but the fault codes will show if this is the case - or you can pull the pump unit plug out of the ABS unit and see if it has continuity with a multimeter - should be a low number of ohms. 8 times out of 10, it is wheel bearing.

Posted on Jul 29, 2009

  • 1 Answer

SOURCE: Compurter says PSM and ABS failure

Hi,

Just had same problem this morning. I had noticed that the satnav was malfunctioning (i.e. developed a mind of its own!!) a couple of days ago and then this morning PSM/ABS failure......marvellous!! Anyway, simply disconnected battery, waited 10-15 mins, reconnected battery and hey presto my boxster fired up. However the PSM failure message still showed, so took it for a spin around the block and the message disappeared and, touch wood, everything seems back to normal. I think it must have been a battery problem, so just to safe I am going to get a new battery and hopefully I can look forward to years of trouble free motoring.....one day with the roof down!!!! (Where has the sunshine gone!!!????)

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My abs light don't come on my ford 2003


abs light on dash panel should only light for two seconds upon starting of engine , then go out . if it comes on and stays on then this indicates a fault has been detected in your abs system , by body control module (fault can be any where on car) a code reader will be required to know reason for abs fault

Jun 24, 2015 | Ford Cars & Trucks

1 Answer

I just changed both rear abs sensors on my ve commodore and the stability control and abs fault lights are still coming on. Do I need to reset the computer? If so, how do I do this?


If you fixed whatever problem you had, the dash light
will go out, when the computer scans for faults

I assume you had an ABS System Problem & Codes

Would hope your not changing parts, based on the name of
a code or two

Were those sensors tested & failed a test

NO - then there is your problem-failure to
test & find a fault

Problem may not be found or solved YET

Oct 02, 2014 | Cars & Trucks

1 Answer

Where is sensor located


generally the yaw rate sensor its located at center of frame of the car , between front seats ,
also check each wheel rotation sensor

Jun 18, 2017 | Porsche 911 Cars & Trucks

2 Answers

ABS light stays on on a 1999 sat urn sl2


ANY Dash Light you get, that comes on or stays on after
the motor is running is a possible problem & a possible
fault code should be checked for

I'm at a loss with this site & the questions, because we have had these codes & vehicle systems for well over 30 years, yet no one knows the vehicle is in trouble & you have to check for codes

You need to run to a repair shop within a day, every time any
dash light or check engine light comes on,not ask questions
or continue to use the car

Any codes you get can be googled, to find the system that set
the fault light

Sep 01, 2013 | 1999 Saturn SL

1 Answer

Ford focus 2001 recall


Just like any time you get a check light on your dash

Check for codes & have a shop diagnose the system
with a fault,don't keep using it

Abs & Evap are two different systems & possible
problems

Dec 25, 2012 | 2001 Ford Focus

1 Answer

Abs service message


Check for codes the same as an other time
you get any light on your dash

Use the code to diagnose the system with the fault

Component test & resolve

Been that way since 1981--32years

Nov 20, 2012 | 2002 Volvo S80

1 Answer

Fiesta duratec 2005 Abs warning light on


Whenever the ABS module turns on the ABS light in the dash it is to alert you to the fact that a fault has occurred in the ABS system and the control module has turned off the ABS brake control, you now have regular non ABS brakes. The waring light will stay on until the fault is corrected. Since a large number of problems would cause this you must get the control module scanned to retrieve the fault code that was set in the control modules memory when it turned on the light. Once the fault code is known the process of diagnosis and repair can begin.

Feb 10, 2012 | 2005 Ford Fiesta 1.6

1 Answer

2003 Boxster. PSM and ABS dash light stay ON


computer is expensive before i invested in one id try to replace the sensors that control those circuits if that dosent solve the problem then id try changing the proms in the computer then lastly the computer.

Apr 04, 2010 | 2003 Porsche Boxster

1 Answer

I have a 2000 porsche carrera 2, which has PSM & ABS warning lights constantly on. I am unable to use the PSM switch, as it does not respond. My mechanic just replaced a speed sensor on the front...


If you have voltage from all of the speed sensors on the wheels, only then think about getting the ABS pump control repaired or replaced. It could be the reluctor.
I repair Volvo and Mercedes without issue so I think you could get the module repaired at a competent repair shop.
Took me 20 minutes to remove, repair and replace the module on the V70. Mercedes took a bit longer as the module was awkward to get to.

Jul 01, 2017 | 2005 Porsche Boxster

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...