Question about Cars & Trucks

Open Question

Bt l 2000 u seal replacement

Need instructions to replace seals in hydraulic pump

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 92 Answers

SOURCE: pinion seal leaking

check your rear diff vent if pluged clean it out and clean up the pinion seal.sometimes if the leak is caused by pluged vent and has not been leaking long once vent is clean sometimes the leak will stop.there is not a specific torque amount because it is rotational torque(how hard to turn pinion).there is a crush sleve on the pinion and if torqued too tight or too loose brg preload will be wrong and brg damage could result.mark and remove drive shaft.remove rear wheels,brakes,axles.so when turning pinion you dont have any drag from brakes or axles.mark the position of the yoke on the pinion.remove yoke,replace seal,reinstall yoke be sure to replace pinion nut.tighten nut until it takes the exact same amount of force to turn pinion as before taking original pinion nut off.hope this helps.

Posted on Oct 22, 2008

Ad
  • 335 Answers

SOURCE: REAR AXLE SEAL LEAKING ONTO BRAKE SHOES NEED INSTRUCTIONS ON HOW TO FIX

Jack up vehicle and support on stands. Remove wheels. Remove differential cover . Locate and remove lock pin that holds cross shaft in. Slide cross shaft out. Push axle inward to release axle c clip. Remove axle and pry out old seal. Install new seal with proper tool.Add some lube to the seal lip to aid axle intallation. Revese removal procedure. This is for a "c" type axle.
Another type has 4 nuts attaching a retainer plate to the backing plate behind the axle flange. In this case the 4 nuts are removed and the axle will come out. This may require a little effort. I think that you have a "c" type axle in your vehicle. Hope this helps. Moe

Posted on Apr 28, 2009

  • 6982 Answers

SOURCE: Rear drive shaft seal leaking

Yes, but you will need to mark the yoke position and exact number of turns to remove the nut or you will change ring and pinion gear lash setting when re-installing it. You can use a large pipe wrench to hold the yoke still while tightening, or get a special tool made for that.

Posted on May 04, 2009

raineystorm
  • 23 Answers

SOURCE: instructions on replacing rear axle end oil seals 90 silverado pu

Where's it leakin?

Posted on May 12, 2009

  • 1 Answer

SOURCE: oil leak in my 98 mazda protege

Could be a rear main seal.

Posted on Feb 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello,my 2000 odyssey leaks oil.guy said its front oil seal but im gonna need time belt,water pump,vtec valve and oil pan gasket.Do i really need all that just to change front seal? $400 for labor?


A leaking front seal will allow oil to get into the area where the timing belt is located. This will cause oil to get on the belt and can cause damage. Since the timing cover must be removed to access the front seal, it is recommended to replace the belt while you are in there. Also, the water pump is driven off the timing belt. Replacement of the water pump is always recommended when replacing the timing belt for two reasons. First, it is easily replaced at this time and it is good preventive maintenance. Secondly, the water pump bearing is under tension from the timing belt and develops a wear pattern. Replacement of the belt without replacing the pump will cause the new belt to wear the bearing in a different pattern, often causing leaking in a very short time after the replacement. This would then result in having to repeat all the labor again to replace the pump. It is easy to see that for $400.00 labor, you don't want to do that again in only 2-3 months. as far as the VTEC valve is concerned, I don't see a relationship to the oil leak. It could just be something else the mechanic found during the inspection. I can find nothing in the remove/replace procedures that requires replacement of the oil pan gasket. Again, maybe something additional that is needed from visual inspection, but not needed for the front seal.

Apr 03, 2016 | 2000 Honda Odyssey

2 Answers

Hydraulic won't lift blade.


sounds like you have a fluid leak, check seals/rubbers and replace if necessary. Might be that you need to replace fluid or top it up with appropriate / similar type

May 25, 2015 | Cars & Trucks

1 Answer

How to replace rear axel seal on a 2000 ford mustang


FOLLOW INSTRUCTION IMAGE

1-SPARE PARTS NUMBERS.

1867c952-7188-4558-b777-3b58b236b539.jpg



2- CON.....
29ce82ff-fe7e-4586-846c-af6a360d09be.jpg

3-NOTICE.
d00f40eb-d155-4f68-82ab-c3b9bf12b2fc.jpg

4- REMOVAL. Use recommended tools.
c26fbb0f-32fb-4452-b05a-3c9c217f6f8d.jpg

5- INSTALLATION.


88f3ffca-c0d9-4445-b491-7209b25fefcf.jpg

Sep 12, 2014 | 2000 Ford Mustang

1 Answer

Replacing water pump & timing belt on 2001 Dodge Stratus R/T. Easy to replace front main seal, too?


oil seal failure is the main killer of rubber timing belts . Oil can come from the crankshaft seal --the cam shaft seal/s and the hydraulic belt adjuster.. So if you have the front off and am replacing the timing belt then it is fools economy not to replace the seals and any idler pulleys at the same time.

Jan 09, 2014 | Cars & Trucks

1 Answer

Need to replace the Front Main Seal


the front main seal is the one that is fitted just behind the front pulley on the crankshaft. Remove the pulley / harmonic balancer and pry out the seal carefully . Place the new seal in place and using a tube the same size as the largest dia of the seal gently tap the seal back into the case until it is flush with the case all the way round.

Dec 07, 2013 | 2000 Plymouth Neon

1 Answer

Hydraulics gone on boot of vw beetle...any ideas?


Sounds like your hydraulic arms need replacing. you can't refill them as they are a sealed unit i'm afraid.

May 08, 2012 | 2000 Volkswagen Beetle

1 Answer

The plow will work fine for a hour. After that the plow gets real slow. Note older stlye hydraulic under the hood cables. I changed the fluid a couple of times. Everything is tight.


It may be the seals swelling as the fluid heats up from use. Are you using trans. fluid or the 'blue stuff' designed for hydraulic systems? I had a similar problem with my 1st plow truck, I found that spraying the seals at the shafts of the up/down piston and angle pistons seemed to help, although only for a while, requiring spraying every few driveways. Some fluids (trans.) can cause the seals to swell, although I can't recall what type. Unfortunately, to really fix this you probably need to drain the system again, and replace all the seals, and refill with the 'blue' fluid.

Feb 25, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

Replacing a fuel pump on a Ford Contour


Fuel Pump Module —Vehicles with Returnless Fuel System
Special Tool(s) Wrench, Sender Unit, Fuel Tank
310-065A (23-054) Removal
syp~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
  1. Remove the fuel tank.
  1. Using the special tool, remove the fuel pump locking ring.
  1. Remove the fuel pump module.
    • Rotate the pump counterclockwise to remove.
  1. Remove and discard the O-ring seal.
Installation
syp~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
  1. Install a new O-ring seal and locking ring.
  1. To install, reverse the removal procedure.

Jan 07, 2010 | 2000 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...