Question about Cars & Trucks

Open Question

Dodge 06 cummins wastegate solenoid fuse# - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: cant find the throttle positioning sensor on my 06

There is NO throttle position sensor on a diesel because there is no throttle body or throttle plate. I'm guessing however that you are looking for the TPS because you got a trouble code that said something to the effect of "Throttle Position Sensor Out Of Range" or something like that. I had the same trouble code, I'm still trying to figure it out, it has sense somehow caused by a/c compressor to stop turning. Maybe unrelated, but it sure seems to be.

Posted on Jul 11, 2009

Ad
  • 1 Answer

SOURCE: Trouble code P1740 on 1999 Dodge Ram 2500

I had the same code on my 2001 dodge 2500. The truck wouldn't shift from 3-4. I pulled the trans pan off and replaced a broken spring ($2.00). It is behind a thin plate with 3-4 small torq screws. You don't have to remove the valvebody. Only took me 45 minutes to fix.

I would like to give thanks to Jeff Russel from Teal automotive. He said this is a very common problem. He sells any part for any automatic Transmision and his prices are very affordable.
Here is a link to the website.
http://www.tealautomotiveinc.com/

Hope this helps.

Posted on Jul 19, 2009

  • 148 Answers

SOURCE: I have a97 5.9 cummins when I throttle up it

Check hose connections at intercooler

Posted on Feb 07, 2010

Testimonial: "with everything new I think it's something I overlooked or adjustment thanks"

  • 340 Answers

SOURCE: 2000 Dodge Cummins is blowing fuse on the starter

wire that goes to the starter not the main wire there is a smaller wire that sends electric from the switch to the starter solinoid might be shorting out (skinned wire between the starter and the ignition switch/fusebox

Posted on Mar 03, 2010

Testimonial: "Thanks, I'll check for that! "

  • 262 Answers

SOURCE: what is a wastegate on 2004 dodge 5.9L cummins

The wastegate is a valve that regulates the ammount of boost that you turbocharger produces. The wastegate opens to release boost pressure.
This valve is electronicly controlled based on inputs to the onboard computer.

Posted on Mar 11, 2010

Testimonial: "where is it located on 5.9L dodge? thanks alot !"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just bought. 5.9 cummins Can`t get it to start without pushing gas pedal slightly. Runs good after warms up. Still have to give it fuel to start.


Numerous Conditions May Cause Engine to Crank But Not ...

repairpal.com > Problems > Dodge > Ram 2500
2006 Dodge Ram Laramie 2500, 5.9i liter Cummins ... I know in the old days the dodges had a way about starting up an engine and that would be where.

White smoke, rough idle at startup - Dodge Cummins Diesel Forum

www.cumminsforum.com > ... > 3rd Gen. Powertrain
Jun 5, 2010 - 9 posts - ‎7 authors I have an 06 Dodge 5.9L that has a light white smoke and rough idle when first ... 2006Ram 2500 QCSB 4x4, 3" Carli coils w/ 1" Daystar spacer, ... Still ran good tho, dispite the exact conditions you describe on Cold Start up.

Oct 20, 2015 | 1995 Dodge Ram 3500

2 Answers

Jeep grand cherokee 2.7 crd I have a problem about code p0243 thans for your help.


DTC P0243 - Turbo/Super Charger Wastegate Solenoid A
Description: Open or shorted condition detected in the turbocharger wastegate solenoid control circuit.


Here is the flow chart for that code (some images could need to clicking for zoom)...

P0243-WASTEGATE PRESSURE CONTROL PWM

zjlimited_337.gif

For a complete wiring diagram Refer to Section 8W.

When Monitored: When the ignition is on.
Set Condition: The ECM detects an open or short circuit in the Wastegate solenoid circuit.

Possible Causes
DAMAGED WIRING HARNESS OR CONNECTORS
WASTEGATE SOLENOID
(F504) FUSED IGNITION SWITCH OUTPUT OPEN
(K139) WASTEGATE SOLENOID DRIVER CIRCUIT OPEN
(K139) WASTEGATE SOLENOID CIRCUIT SHORTED TO GROUND
(K139) WASTEGATE SOLENOID DRIVER SHORTED TO VOLTAGE
(K139) WASTEGATE SOLENOID DRIVER CIRCUIT SHORTED TO ANOTHER CIRCUIT
ECM
INTERMITTENT CONDITION

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)

Diagnostic Test
1. DAMAGED WIRING HARNESS OR CONNECTORS

zjlimited_338.gif

Turn Ignition off.
Disconnect the ECM harness connectors.
Disconnect the Wastegate Solenoid harness connector.

NOTE: Check connectors - Clean/repair as necessary.


Are any wires or pins damaged?

Yes
Repair or replace any damaged wire or connectors.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 2


2. WASTEGATE SOLENOID

zjlimited_339.gif

Reconnect the ECM harness connector.
Reconnect the disconnected Wastegate Solenoid harness connector.
Turn the Ignition on, engine not running.
Disconnect the Wastegate Solenoid harness connector.
Connect an incandescent test light across the supply and driver pins at the Wastegate Solenoid harness connector.

NOTE: The ECM will perform a self check of the circuit after approximately 30 seconds, which should light the incandescent test light.


Does the light illuminate brightly after 30 seconds of being connected?

Yes
Replace the Wastegate Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 3


3. (F504) FUSED IGNITION SWITCH OUTPUT OPEN

zjlimited_340.gif

Connect an test light between the Wastegate Solenoid connector Fused ignition switch output circuit and battery negative.
Compare the test light brightness to that of a direct connection to the battery.

Does the light illuminate brightly?
Yes
Go To 4

No
Repair the open (F504) Fused Ignition switch output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).



4. (K139) WASTEGATE SOLENOID DRIVER CIRCUIT OPEN

zjlimited_341.gif

Disconnect the ECM harness connectors.
Measure the resistance of the Wastegate Solenoid driver circuit between the Wastegate Solenoid harness connector and the ECM harness connector.

Is the resistance less than 10 Ohms?
Yes
Go To 5

No
Repair the open (K139) Wastegate Solenoid control circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).


5. (K139) WASTEGATE SOLENOID CIRCUIT SHORTED TO GROUND

zjlimited_343.gif

Measure the resistance of the (K139) Wastegate Solenoid driver circuit between the Wastegate Solenoid harness connector and battery negative.

Is the resistance less than 10 Ohms?
Yes
Repair the (K139) Wastegate solenoid circuit shorted to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

No
Go To 6


6. (K139) WASTEGATE SOLENOID DRIVER SHORTED TO VOLTAGE

zjlimited_344.gif

Measure the voltage between the (K139) Wastegate Solenoid driver circuit at the Wastegate Solenoid connector and battery negative.

Is the voltage less than 1 volt?
Yes
Go To 7

No
Repair the (K139) Wastegate solenoid driver shorted to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).


7. (K139) WASTEGATE SOLENOID DRIVER CIRCUIT SHORTED TO ANOTHER CIRCUIT

zjlimited_345.gif

Measure the resistance between the (K139) Wastegate Solenoid driver circuit in the ECM harness connector and all other circuits in the ECM harness connectors.

Is the resistance less than 10 Ohms?
Yes
Repair the (K139) Wastegate solenoid circuit shorted to another circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING)


No
Go To8


8. WASTEGATE SOLENOID

zjlimited_346.gif
Reconnect the ECM harness connector.
Reconnect the disconnected Wastegate Solenoid harness connector.
Turn the Ignition on, engine not running.
Disconnect the Wastegate Solenoid harness connector.
Connect an incandescent test light across the supply and driver pins at the Wastegate Solenoid harness connector.

NOTE: The ECM will perform a self check of the circuit after approximately 30 seconds, which should light the incandescent test light.


Does the light illuminate brightly after 30 seconds of being connected?
Yes
Refer to the INTERMITTENT CONDITION Symptom (Diagnostic Procedure).

No
Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).

------------------------------------------------------------------------------------------------------------------------------------------------

Keep us updates.

May 04, 2011 | 2003 Jeep Grand Cherokee

1 Answer

I got a 1994 dodge intrepid and I have 2 codes up on it and i dont know what they are. Code 35 and 45?


Fault Code 35
Description: Radiator fan relay circuit is open or shorted
Power loss light: Off
Limp-in mode: None

Possible Causes:
Bad connection or wiring - Check the wiring and connections between the logic module and the relay. Clean and regrease any corroded connectors with dielectric grease and repair any shorts.

Bad relay - Disconnect the relay and apply 12V across the coil terminals (between the white wire and either of the other two terminals on the small connector). You should hear a click for either of the two termials and the connection between the grey wire and the other two terminals of the large connector should be shorted.

Diagnostic Method
Trigger Parameters
- Near 0V or near 12V not detected when the relay is turned on or off, respectively
Results If Component Fails
Fault code 35 is stored.


Fault Code 45
Notes: For Turbo models only

Description: Turbo boost limit exceeded
Power loss light: On
Limp-in mode: None

Possible Causes
Vaccum leak - Check all vaccum lines between the wastegate actuator, manifold, and wastegate solenoid. Also check the line to the MAP sensor. Repair or replace any bad lines.

Wastegate solenoid failure - The wastegate solenoid is located in the right, front fender next to one to three other solenoids. See the Understanding Solenoids page.

Bad connection or wiring - Check the wiring and connections between the logic modle (or SMEC) and the wastegate solenoid. Clean and regrease any corroded connectors with dielectric grease and repair any shorts. This condition may be accompanied by a code 36.

Wastegate actuator spring failure - Try to slide the wastegate to wastegate actuator push rod into the actuator. It should not move. Try to pull it out. If it pulls out with little effort (even if it springs back in), replace the actuator.

Jammed wastegate - Disconnect the wastegate actuator pushrod and swing the wastegate arm on top of the turbo. It should have about a 50 degree swing. Make sure the lever and push rod are clear of any obsticles that may cause them to jam (the heat shield below the fuel rail is a major culprit).

Diagnostic Method
Trigger Parameters
- MAP sensor output voltage has exceeded overboost cut-off point

zjlimited_942.jpg

Following years are probably the same as 1987, but I don't have any hard data to back that up. Some have said that 4.74V was the max for Turbo I engines of later years. Some information indicates that the Turbo II with an automatic had a cut-off of 4.96V, but I don't know of any Turbo II vehicle that had an automatic transmission.

Results If Component Fails
A fault code 45 is stored, the power loss light is turned on, and the fuel injectors are shut off. Once the boost has fallen to 3 psi to 5 psi, the fuel injectors are turned back on and the power loss light is turned off. The overboost cut-off point for a particular vehicle depends on the year, engine, and transmission.


Keep us updated.

Mar 29, 2011 | 1994 Dodge Intrepid

2 Answers

Check engine codes for a 1997 stratus the codes coming up are 12 31 and 55


12 Recently disconnected the battery (always stored)
55 End test.

CODE 31... depending on the model, code 31 can refer to two different systems. Please choose from one of the above links for specific information on each system.

Wastegate Solenoid Circuit Error
The ECM regulates turbocharger boost by opening and closing the "wastegate" as necessary. (The wastegate is a vacuum operated bypass valve that limits the ability of the turbo to provide boost.) The Wastegate Solenoid regulates the vacuum supply to the wastegate for proper operation.

Fault Code Description
  • 31 - Wastegate Solenoid circuit error
Symptoms
  • Lack of power or engine "ping" due to overboost by the turbocharger
Common Problems
  • The wastegate solenoid would be the most common cause for code 31 to set
  • Code 31 does not indicate a problem with the turbocharger or wastegate


Gear Position Switch (PRNDL) Error The Gear Position switch tells the ECM which position the shifter is in. The ECM will use this information to inhibit starter operation, change the transmission shift pattern as necessary, and provide the information for the electronic shift indicator display on the dash.

Fault Code Description
  • 31 - Gear Position switch (PRNDL) error
Symptoms
  • Engine may not crank over in Park or Neutral
  • Electronic shift indicator may flash
Common Problems
A maladjusted or failed Gear Position switch would be the most common cause for a code 31


Hope helps with this (remember rated this post).

Jun 30, 2010 | 1997 Dodge Stratus

1 Answer

2004 Dodge Cummins 600 engine code P0243


P0243 Turbocharger Wastegate Solenoid 1

You can find them all here:

http://www.allpar.com/fix/computer-codes.html

Jun 21, 2010 | 2004 Dodge Ram 3500 Truck

1 Answer

What is a wastegate on 2004 dodge 5.9L cummins diesel?


The wastegate is a valve that regulates the ammount of boost that you turbocharger produces. The wastegate opens to release boost pressure.
This valve is electronicly controlled based on inputs to the onboard computer.

Mar 10, 2010 | 2004 Dodge Ram 2500

1 Answer

06 cummins wont start


COULD BE GLOW PLUGS NOT OPERATING.CHECK GLOW PLUGS FUSE AND RELAY.THE FUEL TRANSFER LIFT PUMP NOT WORKING CHECK ITS FUSE AND RELAY.OTHER POSSIBLE CAUSES.STOP UP PRIMARY FUEL FILTER.AIR IS GETTING IN FUEL SUPPLY LINE.FAULTY INJECTION PUMP.OR FAULTY PCM.

Jan 25, 2010 | 2006 Dodge Ram 2500

1 Answer

Headlights not working


check fuses in under hood fuse box let me know i will at some diagrams for you hey vote for me ok

May 26, 2009 | 2006 Dodge Ram 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...