Question about Cars & Trucks

Open Question

Headlight adjustment on a keeway f-act 50

How do you adjust headlight in a fixed unit if the lamp is too low

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2006 Pontiac G6-GTP How do I adjust the headlights.

to raise you headlights there is a small brass allen screw located above each headlight under the hood. to raise your headlights turn clockwise until they reach the desired level.

Posted on Oct 23, 2008

  • 2 Answers

SOURCE: Adjusting headlights on 2003 honda accord

Further to Emmisionwiz's answer that worked for me - the holes are in the black plastic covering the radiator support, to each side more or less in line with the headlights. They are marked with an "A" and rotation directions for UP and DOWN. The Phillips screwdriver goes into the hole about 45 degrees from vertical and engages the adjusting rack, where the teeth of the Phillips screwdriver are the pinion. If you shine a flashlight down the hole you can see the rack teeth and all becomes clear. But you will need a long Phillips screwdriver and a little bit of luck.

In the owner's manual it says the lights are adjusted correctly at the dealership and if they need adjustment because of a trailer then take the car to a Honda certified mechanic.

I have a 2004 Accord also and the method is the same for that one too.

Posted on Feb 08, 2009

c17hydro
  • 2984 Answers

SOURCE: headlight adjustment

AIMING The head lamps should be aimed using a special alignment tool, however this procedure may be used for temporary adjustment. Local regulations may vary regarding head lamp aiming, consult with your local authorities.

  1. Verify the tires are at their proper inflation pressure. Clean the head lamp lenses and make sure there are no heavy loads in the trunk. The gas tank should be filled.
  2. Position the vehicle on a level surface facing a flat wall 25 ft. (7.7 m) away.
  3. Measure and record the distance from the floor to the center of the head lamp. Place a strip of tape across the wall at this same height.
  4. Place strips of tape on the wall, perpendicular to the first measurement, indicating the vehicle centerline and the centerline of both head lamps.
  5. Rock the vehicle side-to-side a few times to allow the suspension to stabilize.
  6. Turn the lights on, adjust the head lamps to achieve a high intensity pattern.
9ca7b70.gif

Posted on May 22, 2009

  • 1986 Answers

SOURCE: HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 06, 2009

  • 4793 Answers

SOURCE: 2001 VW Jetta Headlight adjustment. Headlights

sometimes the headlights stick to the adjusters,just pull/push(wiggle it)to free it, then try setting beams.

Posted on Apr 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where, exactly, are the headlight adjusters for the drivers side headlights?


What is the proper adjustment/
Head light adjusters are part of the head light assembly and yes high and low beam are adjusted as one unit normally. Proper adjustment is done on a machine, at an equipped facility.

Mar 27, 2016 | Cars & Trucks

1 Answer

Just bought a used 05 subaru impreza. Noticed the right head lamp is pointed too high. where is the adjustment screws to lower the lamp. It seems great on the horizontal just needs to be adjusted on the...


I hope this info helps!

ADJUSTMENT

HEADLIGHT AIMING

CAUTION: Turn off the light before adjusting headlight aiming. If the light is necessary to check aiming, do not turn on for more than 2 minutes.


  1. Before checking the headlight aiming, be sure of the following:
    • The area around the headlight has not sustained any accident, damage or other type of deformation.
    • Vehicle is parked on level ground.
    • The inflation pressure of tires is correct.
    • Vehicles gas tank is fully charged.
    • Bounce the vehicle several times to normalize the suspension.
    • Make certain that someone is seated in the driver s seat. Turn the headlights on and then adjust the low beam pattern to the following positions on the screen.
  1. Position the headlight beam leveler switch to "0" .
129148368


129148369


129148370



  1. Rotate the adjusting screw (A) to adjust aim.

Aug 01, 2011 | Subaru Impreza Cars & Trucks

1 Answer

Dodge charger fuse box , where the fog lights relay goes ?Thanks


lx_front_relays.jpg


Cavity/ Fuse /Circuits
1/ 20 Amp Yellow/ Left High Beam Headlight
2/ 20 Amp Yellow/ Right High Beam Headlight
3/ 15 Amp Dk. Blue/ Adjustable Pedal
4/ 20 Amp Yellow/ Horn
5/ 25 Amp Clear/ Headlamp Washer - If Equipped
6/ 15 Amp Dk. Blue/ Front Control Module (FCM)
7/ 20 Amp Yellow/ Fog Lamp
8/ 15 Amp Dk. Blue/ Park Lamp
9/ 15 Amp Dk. Blue/ Non ABS Brakes
10/ 5 Amp Orange/ Starter
11/ 20 Amp Yellow/ Auto Shutdown/Powertrain Control Module (PCM)
12/ - -
13/ - -
14/ 25 Amp Clear/ Powertrain Control Module
15/ 20 Amp Yellow/ Injectors, Ignition Coils
16/ 15 Amp Dk. Blue/ Powertrain Control Module
17/ 30 Amp Pink/ Antilock Brake System (ABS) Valves
18/ 30 Amp Pink/ Windshield Wiper/Washer
19/ 50 Amp Red/ Radiator Fan
20/ 20 Amp Lt. Blue/ Starter
21/ 50 Amp Red/ ABS Pump Motor
22/ 40 Amp Green/ Radiator Fan High/Low
23/ 50 Amp Red/ High Intensity Lighting
24/ - -
25/ 30 Amp Pink/ Lighting Left High Beam/Right Low Beam
26/ 20 Amp Lt. Blue/ Transmission
27/ 30 Amp Pink/ Lighting Left Low Beam/Right High Beam
if this helps please rate 4 thumbs up.

Jan 21, 2011 | 2007 Dodge Charger SRT8 Sedan

1 Answer

How I adjust headlights on a 1999 grand am?


  • Determine the type of headlights you have on your car. You can only adjust composite headlights if they bolt to adjuster plates. For dual headlights, look on the headlights for four adjustment screws per side. Sealed beam units have interior adjustment screws under the hood.
  • 4 Locate your adjustment screws. On sealed beam units, you may need to remove the trim screws and pull the trim off to reveal the Torx screws.
  • 5 Begin with you headlights turned on to the low beam. Use a Torx screwdriver for sealed beam units and Phillips screwdrivers for other types of headlights.



  • Dec 09, 2010 | 1999 Pontiac Grand Am GT

    2 Answers

    Why is it that my low beam lights are really low


    Bulbs fitted incorrectly.Or your adjustment is out.of line.Adjust them behind the lamp.good luck.

    Aug 01, 2009 | 2002 Chevrolet TrailBlazer

    2 Answers

    How do you adjust the headlights on a 2006 dodge ram 2500 ?


    The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

    You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

    Jul 28, 2009 | Dodge Ram 2500 Cars & Trucks

    3 Answers

    How do I align low beam headlight in 2006 honda odyssey .Right side headlamp set to low will not light up signs on side of road(Stop,yield)


    The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

    You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

    Jul 27, 2009 | 2006 Honda Odyssey

    1 Answer

    How do you change head lights on a 2004 kia sorento?


    The whole headlight assembly needs to be removed from the vehicle to access the lamps inside; especially on the side with the battery (left side).

    Remove 3 10m bolts (one on top two on front)

    Headlight assembly is held in place wth a large Nylon clip ear outer edge at bottom of the unit. Tilt out at the top and then pull forward and upward to remove. It fels like something's gonna break, but it's pretty tough.

    Remove large round cap from behind either high or low beam lamp. Both lamps are hels in with a metal spring clip. Low beam is H-7, high beam is H-3.

    To re-install, press bar into Nylon clip and then install 3 10mm bolts. Use a Torx bit to engage gear teeth and adjust height if necessary. There may or may-not be adjusters for left-right alignment.

    Apr 25, 2009 | 2004 Kia Sorento

    2 Answers

    Head light adjustment 2004 optima


    This is how to adjust 04 Optima headlights:

    For all descriptions, assume that you are standing BEHIND the light assembly.

    On the back of the headlight assembly you will see the bulb cover (round cover with tabs) stamped "OPEN" and an arrow showing which direction to turn to remove. Look toward the 8 o'clock position for driver lamp, 4 o'clock for passenger lamp of this cap. Partially obscured by the sheet metal you will see a black screw 3/4 exposed on the headlight assembly. It is at the edge of the sheet metal and very difficult to see, but it,s there. You may need to remove the assembly to get a better look. If needed, see below for lamp assembly removal.

    How to remove the headlight: There are two 10mm bolts holding the assembly in place. One is above the headlight and the other one is between the headlight and the high beam light. Unplug the two harnesses that hook into the headlight, if needed, and it is ready to be removed the car. Gently work it out of position.

    Take a Phillips screwdriver and turn the black screw - it adjusts the light vertically. Turn it counter-clockwise to make the light go up and clockwise to adjust down. Its as easy once you find the screw.

    Jan 03, 2009 | 2004 Kia Optima

    1 Answer

    Head / fog light adjustment


    on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

    If you only have one nut on each, that will adjust the vertical aim of the headlights.

    If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

    Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

    If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

    Jul 02, 2008 | 1994 Toyota Supra

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    27 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    74896 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...