Question about Cars & Trucks

Open Question

Scania injector problems - Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hay am having problem on my 144 460 engine idling is picking up an dropping, the truck has no power and i did fitted new injectors


Scania 144 460
sure is a big motor
fuel pump pressure to injector and timing important
uneven cylinder compression pressures may be a cause
lack of power
if it has a turbo would suspect internal crack in turbo index-omyln5yzcl4rshihar4so15z-3-0.jpg

ww-omyln5yzcl4rshihar4so15z-3-1.jpg

Jan 22, 2017 | Cars & Trucks

3 Answers

Scania p380 engine malfunction


Engine Malfunction mean you have problem in one of systemes. You must read the fault codes from the dashboard, by pressing diagnosis keys

Jun 16, 2015 | Cars & Trucks

2 Answers

1994 Scania 143 loss of power


check and adjust the injection timing of the pump and set it to spot on as any degrees retarded will affect performance. Check that there is no boost pressure from the turbo being lost from loose hoses and cracked tubes and intercooler. If you engine has a air compressor with a coiled steel line attached to it before the line is connected to a rubber hose to the tank Then replace the coil as it blocks up with carbon and puts the air compressor under constant load. Check for worn brake pivots as dragging brakes use up HP Finally have the truck chassis dyno tested to check for full pump operation as I had experience where the pump was fully rebuilt but the cam bearings in the pump were not replace and the pump was way off setting. ON a chassis dyno tested in direct gear the reading should ne around 410 hp at the rear wheels depending on the tread of the tyres. The test will show at what rpm\'s the governor in the pump is not performing as the power curve will not follow the set line.

Jan 02, 2014 | Mercedes-Benz 300-Class Cars & Trucks

1 Answer

Scania v 480


refer to the Scania service department for the code readings interperation as they are specific to Scania codes.

Dec 14, 2013 | Cars & Trucks

1 Answer

I need to now about scania 380 6 sylinder edc setings


scania 380 have engine 11 liter the fuel system EDC ms6(unit injectors)
good fuel consption no much faults good power

Mar 07, 2013 | Cars & Trucks

1 Answer

Scania 114 indicates edc light and has no power


Scania is a Swede truck not a Isuzu!
in what country, (we are usa forum)
what year car
what engine ? Lack of engine power but whats there under the hood, we have zero clues.

that is no isuzu, npr or elf, nop
14301679-42iidcav35y5jytkvom0adnh-2-0.jpg

Sep 11, 2012 | Isuzu Cars & Trucks

1 Answer

How can i soft the problem about engine jerking scania truck p380


P0380 Glow Plug/Heater Circuit A -Circuit Malfunction
P0381 Glow Plug/Heater Indicator/Warning Lamp Circuit
This is the code i think your seeing so you need some new heater plugs or maybe a fuse or a timer relay but as this is a direct injection scania diesel then it will start anyway unless you in ice road truckers land ,Now iam unsure about the year of this vehicle but iam assuming its a newer version than i worked on 30+ years ago so its common rail injection and all computer controlled which means its not a mechanic like old fleet fitter here but a Bosch diesel specialist to connect up to the computer and see whats what ,now if it had the old bosch injector pump and it was 40 yrs old then i soon beat it into submission for you but this electronic controlled although i know whats its doing and how it does it i cannot even think about trying to repair it without the 10,000 euros worth of fancy electronic gear and the newer ones have to be connected to the internet back to the factory owing to the encrypted software used to prevent the chinese from copying it and selling it over the internet .

Feb 14, 2012 | Cars & Trucks

1 Answer

Scania 144 530 tappet settings.


need guid to set scania engine dc16 45a 1066579 tappets

Feb 12, 2012 | Cars & Trucks

1 Answer

Scania 114G 340 is not running after EDC warnings, error codes 53 and 54 can some one help me out.


the fault codes 53-54 is problem in cylender 3and4 unit injectores but that is not the main cause to make the engine is not starting check the overflow valve and the fuel pump or another fault code in the control unit

May 30, 2010 | Isuzu VehiCROSS Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...