Question about 1997 Infiniti.5 Q45

1 Answer

What is the 1997 infiniti q45 rod bearing cap bolt torque?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I have had good luck with AUTOZONE.com click on repair help and specs. I tried it for your car and it gives the details torque plus turn method . Hope this helps.

Posted on Jul 11, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1992 infiniti q45

motor run ruff and will not ideal

Posted on Aug 13, 2008

SteveRand
  • 210 Answers

SOURCE: lost power while driving

More often, the voltage regulator in the alternator is worn.

It usually screws on/into the alternator, and when you pull it out it has two "brushes" which are usually just silver/copper blocks. Those blocks are designed to wear down, and they are pushed onto the alternator with a spring.

The part is cheap on most cars, and you can do it yourself quite easily. Just don't forget to unplug the battery before unscrewing the regulator!

Posted on Feb 06, 2009

  • 563 Answers

SOURCE: alternator for 1998 infiniti q45

You simply disconnect the battery, and use sockets/wrench to remove the alternator. Make sure the battery is fully charged up before you install the new alternator.

Posted on Nov 10, 2009

  • 50 Answers

SOURCE: no lights working on dash and console of my 1997

usually located drivers side behind kick panel or on lower portion dash..

Posted on Sep 02, 2010

johnjnail
  • 1702 Answers

SOURCE: 1997 Q45 INFINITY, TROUBLE CODE U3FFF, TCS off

i am not sure were or how you got that code. there are no trouble codes starting with a U or ending with any letter all engine performance codes will start with a P and then 4 numbers all ABS/TCS codes will be only 2 numbers and cant be retrieved with a code reader they must be retrieved by means of a test procedure i can get the procedure for you if you want it i will need your e-mail to send it to because fixya does not have enough space to post it on there sight.

Posted on Apr 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need torque sequence for rod bearing caps


There is no sequence for the rod caps Since there are only 2 bolts per cap you only have to snug up each bolt then apply half the listed torque value to each cap bolt. then continue back and forth on them until the end torque value is applied to both bolts.

Apr 29, 2015 | 1996 Pontiac Bonneville SE CA Value

2 Answers

What the torque specs. For a 2002chevys10 4.3vortex mains and rod bearing


Torque Specs Database

Type: Dim: Length: Head: Nut Grade: 20 Ft-Lbs 240 In-Lbs 27.12 N-m Connects: Connecting Rod To Engine Block Years: All Vote Record: Vote Note: Vortec - Rod Cap Nuts - 2 Steps: 20 FtLbs; +70degs

http://ww2.justanswer.com/uploads/ZZdaryl/2009-06-14_153454_torque.pdf

Main Bearing Cap Bolt 4.3L Step 1 15 ft lbs (20) Step 2 Additional 73 Degrees

i don't know if that's correct for main bearing caps since another link states it's much higher

4 3 Vortec Piston Specs eHow

hopefully a GM guy will chime in to confirm the main bearing torque

the rod bearing torques are the same on all the other links

Mar 25, 2015 | 2002 Chevrolet S-10

1 Answer

What is the torque for the main and rod bearings on a 2005 dodge stratus 2.7L automatic v6?


Main bearing cap bolts there is a outer cap bolt that are torqued to 20 ft lbs + 1/4 turn. Then there a inner cap bolt that are torqued to 15 ft lbs + 1/4 turn. Con rod bolts are torqued 20 ft lbs +1/4 turn

Jul 06, 2014 | 2006 Dodge Stratus

1 Answer

Torque settings on cranck sharf bearings


Torque settings for V-6 engine.
Main bearing cap bolts torque:
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Connecting rod cap bolts torque:
Torque: 24.5 N·m (250 kgf·cm, 18 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Feb 11, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Torque specs for 1.5 kia rio connecting rod


TORQUE SPECIFICATIONS kia rio
Cylinder Head Bolts:
(21.7ft.lb) or (3.0kgf.m) 90?

May 22, 2010 | 2001 Kia Rio

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Need torque for a 2000 Toyota Celicia GT 1.8L


Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Mar 18, 2010 | 2000 Toyota Celica

1 Answer

Torque specs


hi,
Main Bearing Cap Bolts 75-85 56-62
Connecting Rod Cap Nuts 31-39 23-28

Jul 05, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Torque specs


2002 2.0L Duratech.

Don't have 2004 2.3L

  • NOTE: Use new connecting rod bearing cap bolts.
    NOTE: Do not fully tighten the connecting rod bearing cap bolts at this stage.
    Install the bearing caps.
  • Rotate the crankshaft through 180 degrees and insert pistons 2 and 3.
  • Position the corresponding bearing shells, clean and free of oil, into the connecting rod and the connecting rod bearing cap.
  • Coat the inner side of the bearing shells with engine oil.
  1. NOTE: The crankshaft must rotate freely, if necessary check and adjust the bearing clearances.
    Tighten the main bearing and connecting rod bearing bolts.
    1. Tighten the main bearing bolts in two stages.
      • Stage 1: 25 Nm.
      • Stage 2: 60 degrees.
    1. Tighten the connecting rod bearing bolts in two stages.
      • Stage 1: 35 Nm.
      • Stage 2: 90 degrees.
96fc939.gif

Apr 28, 2009 | 2004 Ford Focus

3 Answers

Need torque specs


Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees

Oct 14, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14200 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...