Question about Cars & Trucks

Open Question

Crankshaft sensor 4.0. 1999 jeep cherokee sport

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 41 Answers

SOURCE: my 1996 jeep cherokee sports

The CPS is one of the first places to start, but remember that the signal goes thru the ECM first, which ultimately supplies power to the coil, I've had to replace the ECM on my 96 Grand Cherokee 4.0 3 times. The dealer wanted to replace the crack and cam sensors, but it was only the computer that was bad.  Sorry I cant give you any definitive answers but I did get it to turn over when I hit the computer with a wrench!

Posted on Dec 12, 2008

  • 41 Answers

SOURCE: no spark

Check the asd relay in the fuse block. Replace it with a known good relay

Posted on Apr 26, 2009

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

  • 285 Answers

SOURCE: crankshaft sensor located 98 jeep grnd cher 4wd 6cy

it is located at the back of the engine on top of the transmission bell housing,the plug runs over to the passenger side of the engine bay and it comes out from behind the engine,you can actually get your hand on the sensor itself from under the hood on the drivers side,and i believe its a 13mm bolt holding it in,the new sensor will have a sticker on the end of it...leave it there,it is used for correct spacing between the sensor and the flywheel,hope this helps

Posted on Sep 23, 2009

Testimonial: "Everything was just like you said but as a not atleast for my jeep it is an 11mm not 13mm. Works great so far (keep fingers crossed) "

emissionwiz
  • 75222 Answers

SOURCE: replace a crankshaft position sensor on a 1996

1st I need to know what engine you have, 4.0L or 5.2L V8.

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the css819 sensor located on a 1997 jeep Cherokee Laredo and how do I change it


Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info

1997 Jeep Cherokee Sport Crank Sensor Replacement

Crankshaft Position CKP Sensor Removal

Mar 06, 2016 | Jeep Cars & Trucks

2 Answers

I have a 1998 Jeep cherokee sport. Was driving today and it died. Now there is no spark and no power to fuel pump. Changed fuel pump today and it won't run. Recently replaced oxygen sensors too


U need to check the crankshaft position sensor. The fuel pump will only have power for 2 seconds I till it sees a crank signal. It' controls the asd relay which turns on your spark and fuel

Apr 19, 2013 | 1998 Jeep Cherokee

2 Answers

No spark on a 1998 Jeep Cherokee Sport w/ 4.0L


Have you checked the computer for trouble codes ?
Could be a long list - pickup module, coil, ignition module, distributor, rotor, power relay, etc.

Jun 28, 2012 | 1998 Jeep Cherokee

1 Answer

I hae a 1993 Jeep Cherokee Sport. It starts fine


What you have is a crankshaft position sensor that is breaking down under a hot condition .Also the sensors electromagnetic field is leaking out electrodes so when it rains for a while and the air is very damp this basically shorts out the sensor.The sensor is located on the back side of the engine, drivers side were the transmission and engine come together. I hope this will help!

Jul 22, 2010 | 1992 Jeep Cherokee Sport

1 Answer

1999 jeep cherokee sport it wont start cranks but wont fire


Figures...I'd use 2&3 as b&c Open reading means that with the meter set to ohms and turned on, the meter should read the same connected to the terminals as it did before you connected it.

Oct 29, 2009 | 1999 Jeep Cherokee

2 Answers

Where is the crankshaft position sensor located on a 1996 Jeep Cherokee Sport? Is there a website with removal and installation instructions?


i acn give the position of the crankshaft
it is located on the rim of the bell housing at 11:00 if you are facing front, 1:00 if you are standing in the front looking back.

Jun 14, 2009 | 1996 Jeep Cherokee Sport

2 Answers

Where is the crankshaft sensor located in a 2001 jeep cherokee sport?


Your sensor is located next to the crankshaft pulley. it is halfway into the block and, the housing will have wire clips protruding outwards. it should be around the top left or right side of the pulley.

Jun 01, 2009 | 2001 Jeep Cherokee

1 Answer

In my 1996 jeep cherokee sprot i have a problem with starting my car after i have been driving it i dont know what it could be the cam positioning sensor? getting to hot and sometime it will just die


The crankshaft position sensor located @ 11:00 on the rim of the bell housing from the driver position. seems to be a very common problem on the Cherokee. They cost between $70 and $80. or $250 installed.

Mar 28, 2009 | 1996 Jeep Cherokee Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...