Question about 2007 Ford Fusion I4 SEL Sedan

Open Question

Code p2111 TAC system stuck open...what part is this and how hard is it to fix???

Wrench light comes on and throttle wont work...come to complete stop and car shuts off...turn back on and keeps doing it every few miles

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
moparownr
  • 667 Answers

SOURCE: P2104

The p2104 code was set because the PCM had to set the idle speed, the p2112 was set to indicate that your throttle body was stuck closed. You can try to remove the throttle body and clean it, check to ensure that it opens smoothly, check the TPS connector to ensure that it is plugged in correctly, reset the light and if the problem returns, you will probably have to install a new throttle body assembly. Hope this helps, let me know

Posted on Dec 08, 2009

Ad
dropndeal
  • 134 Answers

SOURCE: the tool light comes on after traveling

The dealer should be able to read the trouble code.

This can occur with the TCM (Transmission Control Module) and/or ECU program. This may require either a re-flash or a program download to the ECU. The ECU program is not a warranty item, but is typically in the $75 to $100 range.

However there is a Technical Service Bulletin (TSB) for the “wrench light”.

TSB 05-14-4

This article supersedes TSB 05-09-15 to update the Issue and Dealer Coding.

FORD:
2003-2005 Thunderbird
2005 Crown Victoria, Mustang
2004-2005 Explorer, F-150
2005 E-Series, Expedition, F-Super Duty
LINCOLN:
2003-2005 LS
005 Town Car, Navigator
MERCURY:
2005 Grand Marquis
2004-2005 Mountaineer

ISSUE:
Some vehicles built 11/29/2004 and prior may exhibit the wrench light on with both P2106 and P2135 diagnostic trouble codes (DTCs).

ACTION:
Replace the throttle position sensor (TPS) following the instruction sheet included in the TPS service kit. Reprogram the powertrain control module (PCM) to the latest calibration using WDS release B36.11 and higher, or B37.2 and higher. This new calibration is not included in the B37 CD. Calibration files are also available at www.motorcraft.com

I hope this helps!

Posted on May 06, 2010

  • 2 Answers

SOURCE: Engine goes to idle while driving

P2104 Throttle Actuator Control System - Forced Idle
P2106 Throttle Actuator Control System - Forced Limited Power
P2111 Throttle Actuator Control System - Stuck Open
P2112 Throttle Actuator Control System - Stuck Closed
P2135 Throttle/Pedal Position Sensor/Switch “A” /"B" Voltage Correlation
I looked it up and I will give you a web site I got it from http://www.f150online.com/forums/v8-engines/280570-p2104-p2106-p2111-p2112-p2135.html I hope this helps

Posted on May 25, 2009

  • 1 Answer

SOURCE: Wrench light on a 2006 Ford Explorer

Change your imput and output speed sensors on the transmission. Not covered by the drivetrain warrenty. I had the same problem!

Posted on Aug 02, 2009

  • 3640 Answers

SOURCE: the following diagnostic codes P2104, P2111, and

all the codes point to throttle body. clean throttle body, especially around throttle plate. check for loose wires, if problems persist. replace throttle body. p2104 is tac system forced idle, p2111 is tac system stuck open, p2112 is tac system stuck closed. clean throttle body good, and see if this fixes it. then go from there. have a good day !!

Posted on Jan 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Warning light wrench comes on after driving a couple miles but will go off with reset.


It indicates some kind of problem exists or some kind of maintenance is due.

Apr 26, 2016 | Cars & Trucks

1 Answer

I have a 1990 Z24, 3.1. Car runs great for a few miles, but shuts off when I come to a complete stop and the check engine light comes on. If I put it in neutral it starts right back up and runs great. ...


you have a typical lock up selanoid problem in the transmission. very comon on these th125 type of transmission. replaced many in our shop before

Jan 24, 2013 | Chevrolet Cars & Trucks

1 Answer

My 2001 Saturn L200 service light with the wrench keeps coming on. If I drive about 100 miles and park the car when I return to start it that is when the light comes on not while driving. I can not get the...


Service (Wrench) System Check The SERVICE (Wrench) telltale is turned ON by the cluster when it receives a command from the powertrain control module (PCM) or the body control module (BCM). The PCM or BCM will turn the SERVICE (Wrench) telltale ON for all non-emission related diagnostic trouble codes (DTCs) that require that a telltale be turned ON, some DTCs do not turn ON a telltale but are stored to aid in diagnosis.
The SERVICE (Wrench) telltale will also be turned ON if the Antilock Brake System (ABS) control module has detected a fault in its own warning indicator system. If the ABS cannot turn ON its own telltale, a message will be sent to the BCM through the Key Word 2000 data bus to turn ON the SERVICE (Wrench) telltale.
The SERVICE (Wrench) telltale will be turned ON by the cluster for 2-3 seconds, when the ignition is turned to RUN, for a visual system check.

You need to have codes checked .

May 07, 2017 | Saturn L-Series Cars & Trucks

1 Answer

"wrench" light came on and accelerator stop working in traffic


crunk it up ,that's good english . Cranked it up How many miles on the vehicle ! The wrench light is a warning light for the transmission or the electronic throttle control .All new vehicle's have electronic throttle control , there are position sensor's in the APP an in the throttle body an they ware out . It's your responsibility to keep it maintained . Not just to jiffy lube !To the Dealer to have diagnostic's run on the electronics. Accelerator Pedal Position Sensor vs. Throttle Position Sensor

Inside Car Accelerator Pedal Position Sensor vs Throttle Position Sensor

Apr 28, 2017 | 2005 Ford Expedition

1 Answer

Car keeps shutting off on me


try cleaning the throttle body and have the throttle position sensor checked.some throttle bodys need to have a basic setting performed with diagnostic machine.

Oct 12, 2009 | 1996 Volkswagen Jetta

1 Answer

Car Stopping


try this
Here is the most common cause of surges and stalls and low idle rough idle, it is the idle speed control air-bypass valve and throttle valve (IAC for short), they get full of gunk over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Feb 17, 2009 | 2004 Cadillac Deville

3 Answers

Stalling, 'reduced power' light, and OBD code P1125 Manufacturer control air metering...


These trucks have a drive by wire system,we seen a` lot with a broken ground wire on the rear of the drverside cyl head,this is hard to see just feel and give the wire a tug .If the wire is loose or broken the reduced engine power light will come on.

Feb 02, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

3 Answers

2004 dodge ram 1500 5.7 hemi 4x4 4 door 90k miles


Take throttle body off, clean Throttle Body with Carburator cleaner. I had same problem and its the ethynol in fuel that creates a build up in the throttle body which creates this problem. I did what a friend of mine said to do (service manager at Dodge Dealership) it hasnt happened again.

Dec 02, 2008 | 2004 Dodge Ram 1500

2 Answers

How to turn service lights off


get the codes read,get the throttle body update (free from volvo) done,reset service by holding odometer button done and turn on key till lights come on dash and what approx 5 second release and turn off key ,you may need to do it again until it works

Aug 25, 2008 | 2002 Volvo V70

1 Answer

Stalling, 'reduced power' light, and OBD code P1125 Manufacturer control air metering...


My name is Juan Heredia and I'm an ASE certified technician. I have seen this code and this driveability issues before, I will need a little more information about your car to tell you exactly what your problem is, Honda has two different types of throttle bodies for this especific vehicle, drive by wire and cable operated, if your vehicle uses the drive by wire type I would highly recommend to replace the throttle body actuator, if it uses the cable operated one it will be necesary to do a little more testing, let me know if this helps

Jul 31, 2008 | 2000 Honda Passport

Not finding what you are looking for?
2007 Ford Fusion I4 SEL Sedan Logo

Related Topics:

413 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...