Question about Cars & Trucks

Open Question

Honda Element Sc 2008 bank 1 sensor 1. Where is that located..

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: location of bank 1 sensor 1 o2 sensor

Should be in the manifold on the back side closest to the firewall.

Posted on May 04, 2009

Ad
ghassun
  • 499 Answers

SOURCE: check engine light is on...bank 1 sensor1 oxygen sensor

if u have one oxygen sensor then u need to take a deep look at the bottom of ur car it will be somewhere at the Exhaust pipe if u have a catalytic converter then u will have two oxygen sensors one before the catalytic converter & the other will be after the catalytic converter. Note: the catalytic converter is located at after a little bit of beginning in Exhaust pipe.

Posted on Jun 06, 2009

dttech
  • 4803 Answers

SOURCE: where is the bank 2 sensor 1 located.

Oxygen sensors are always numbered like this:

Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Most GM engines have #1 cylinder located on the left bank, (or Driver's Side) of the engine,

So, the answer to your question would be that you are looking for the sensor located before the catalytic converter on the right (or Passenger Side) of the truck.

Posted on Oct 17, 2009

bschilz
  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

7acfed1.gif
d9eb1af.gif

Posted on Oct 20, 2009

roniecon
  • 6826 Answers

SOURCE: were bank 1 sensor 2 located on a 1997 tahoe

bank 1 is the drivers side,and it is the down stream sensor,the one after the cat,converter,If this was helpful,please let us know,thank you.

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locate camshaft sensor 2008 3.6l malibu


Which one ?
Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake

Sep 02, 2016 | 2008 Chevrolet Malibu

1 Answer

Honda accord oxigen sensor bank 1 sensor 1 where is located


bank 1 is the side that has the # 1 cylinder , sensor 1 is the FIRST sensor down stream from motor before catalytic converter the one after catalytic converter is bank 1 sensor 2

Aug 27, 2014 | Honda Accord Cars & Trucks

1 Answer

Where is the ELD on honda crv 2008


Hi,


P1289 - Cylinder Head Temp Sensor High Input
The A/F sensor is a planar dual-cell limit current sensor. The sensor element of the A/F sensor is the combination of a Nernst concentration cell (sensor cell) with an oxygen-pump cell, which transports ions. It has a heater in the element.

The sensor is capable of precise measurement a= 1, but also in the lean and rich range. Together with its control electronics, the sensor outputs a clear, continuous signal throughout a wide range (0.7 < a< air).

The exhaust gas components diffuse through the diffusion gap at the electrode of the oxygen pump and Nernst concentration cell, where they are brought to thermodynamic balance.

An electronic circuit controls the pump current through the oxygen-pump cell so that the composition of the exhaust gas in the diffusion gap remains constant at a = 1. Therefore, the A/F sensor is able to indicate air/fuel ratio by this pumping of current. In addition, a heater is integrated in the sensor to ensure the required operating temperature of 700 - 800?C (1,292 - 1,472?F).

The response (from LEAN to RICH) of the A/F (Bank 1) signal computed by ECM from A/F sensor 1 signal takes more than the specified time.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
# Harness or connectors (The A/F sensor 1 circuit is open or shorted.)
# Air fuel ratio (A/F) sensor 1
# Air fuel ratio (A/F) sensor 1 heater
# Fuel pressure
# Fuel injector
# Intake air leaks
# Exhaust gas leaks
# PCV
# Mass air flow sensor



Thank you.

Jun 07, 2012 | 2002 Honda S2000

3 Answers

2002 dodge caravan engine light on code showing p0135 .please advice.thanks.


  • O2 Sensor Heater Circuit Malfunction - Bank 1 - Sensor 1
  • Basically the ECM Electronic Control Unit has determined your O2 sensor is taking to long to begin reacting properly.
  • The causes could be
  1. O2 heater element resistance could be to high.
  2. An internal short or opening in the heater element.
  3. O2 heater circuit wiring with high resistance.
  4. Open or short to ground in the wiring harness.

  • The fixes are
  1. Check the harness and connector to the O2 sensor for shorts or ground.
  2. Replace that O2 sensor.

  • Bank 1 sensor 1 location for this vehicle is located on the exhaust manifold back by the firewall on top of the manifold..
  • Thank you for using FixYa


Regards, Tony

Jun 19, 2011 | 2002 Dodge Grand Caravan

1 Answer

2003 honda element code po141 o2 heater circuit bank 1, sensor 2 which sensor is this.


This sensor is "downstream" of the catalytic converter. On some Honda installations, this means the sensor is placed halfway down the side of the catalytic converter.

Mar 05, 2011 | 2003 Honda Element

1 Answer

Honda Odyssey 1999 wher is located bank 1 sensor 1


The oxygen sensor for bank 1 sensor 1 is located just behind where the exhaust pipes from the front bank of cylinders and rear bank of cylinders join up. If you look under the car from the front and follow the exhaust pipes, it is the one you can see easily. There are only two oxygen sensors on the car---the one described above is bank 1 sensor 1. The other sensor goes into the side of the catalytic converter. It is bank 1 sensor 2.

Feb 08, 2011 | Honda Odyssey Cars & Trucks

1 Answer

Engine light on--when do scan shows code P0135


P0135=O2 sensor heater circuit malfunction (bank 1, sensor 1)

O2 sensors have built in heaters to help them warm up faster. The O2 sensor in the No.1 bank of cylinders may have an inoperative heater or the wiring to the heater element is damaged. Changing that O2 sensor may correct your problem.

Feb 03, 2011 | 2006 Honda Element

1 Answer

CODE PO155 BANK2 SENSOR 1 WHERE IS THIS SENSOR LOCATED?


A code P0155 may mean that one or more of the following has happened:
* O2 Heater element resistance is high
* Internal short or open in the heater element
* O2 heater circuit wiring high resistance
* open or short to ground in the wiring harness

Possible Solutions:
* Repair short or open or high resistance in wiring harness or harness connectors
* Replace oxygen sensor (cannot repair open or short that occurs internally to sensor)


Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2

Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2

Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.

Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.

Hope helps (remember to rate this).

Oct 02, 2010 | 2002 Mitsubishi Montero

2 Answers

Where are bank 1 sensor 1, bank 2 sensor 1, bank 1 sensor 2, and bank 2 sensor 2


bank one sensor 1 is the bank of cylinders that number 1 spark plug is located in, bank 2 the other side, this assumes u have a V8, the sensor one location is the sensors that are BEFORE THE CATALYTIC CONVERTER, the sensors referred to as sensor 2 are after the ones AFTER THE CATALYTIC CONVERTER IN THE EXHAUST SYSTEM.

Apr 28, 2010 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...