Question about Cars & Trucks

Open Question

2004 Z4 Seat back panel keeps coming off...does anyone have an answer to fix it...two clips up top and two on the side...

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Audi 2004 convertable top malfunction

Just close BOTH the front and back MANUALLY and make sure its in the locked position. (follow the owners manual on how to close it manually). The warning light will go off and the switch will become operational again.
Cheers!

Posted on Dec 30, 2008

Ad
  • 1 Answer

SOURCE: I have a 2004 infiniti sedan g35... the pass side seat does not

i just fixed this problem - the switch is bad - take out the seat - 4 bolts on the bottom 4 corners and then remove the whole switch - either buy a new one around $200 or unsauter the switch and clean it but be careful as there are a lot of parts inside that can fall out. i cleaned mine and it works fine beats spending the money.

Posted on Apr 24, 2009

techbuster
  • 5081 Answers

SOURCE: Needing instructions for the removal of drivers

There are two screws that need to be removed from the front door panel as well as the clips--the screw under the little plastic cover beneath the inside door handle, and an additional screw on the inside of the door, accessible when you open the door up--if I recall correctly, you should see a screw in or near where the air duct is located, where the air blows from your console into the air duct of the door. Hope this helps! There is also a row of metal clips on the top of the panel, which are different than the plastic clips surrounding the rest of the door panel.
Check the below link it may increase your knowledge on your car. http://www.youtube.com/watch?v=zEZ-bcEYdRA&feature=player_embedded#t=12

Posted on Sep 22, 2009

  • 93 Answers

SOURCE: green hydralic liquid coming from convertible top saab 2004 9-3

You are probably leaking hydraulic (ATF) fluid.
Check the lines and cylinders for leaks. Replace any leaking lines or cylinders. Always replace them in pairs.
When the leak is fixed...
Behind the rear seat is the motor/pump/reservoir.
With the top down, fill the reservoir with ATF.
Cycle the system a few times.
Repeat till the reservoir will accept no more fluid.
You can change it to a manual top by removing the bolt at the top of the cylinders and lowering the both shafts down into the cylinders.

Karl at topgunwon.com

Posted on Jan 25, 2010

  • 47 Answers

SOURCE: Remove the plastic seat panel on a 2004 Pacifica?

Instructions with pictures to follow:


4d2b154.jpg

e2f6b1d.jpg

2d180a9.jpg

160bbdc.jpg

b1e023c.jpg

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I removed the drivers seat on my 2004 z4 to clean the carpet, after i put everything back together the air bag light came on how do i get it to turn off


Hi
You will need to take the car to someone with a diagnostic machine ,when you've removed the seat I'm assuming you've unplugged some cables ? If not you could have disturbed the wiring under the seat that controls the airbag which requires a diagnostic machine to reset the light
Hope this helps Nick

Aug 19, 2017 | 2004 BMW Z4

1 Answer

How to change the third break light bulb in a 2007 hyundai sonata ?


From 2006 to 2010, the Sonata's 3rd brake lamp requires the rear package deck be removed to access that bulb.
1. Remove the rear passenger seat bottom (remove two12mm bolts between the seat back and the seat bottom - tilt the seat back forward to locate these bolts).
a. Press the two bottom front edge tabs to release the front of the seat bottom from the floor.
b. Remove seat bottom & set aside w/two 12mm bolts
c. Tilt both seat backs downward
2. Remove the left & right hand shoulder cushions (12 mm bolt at the bottom of each cushion)
a. Remove seat belt from shoulder cushion guide at the top of the cushion
b. Lift up and forward on shoulder cushions to remove them (if equipped with side airbags, disconnect wire harness connector).
c. Set shoulder cushions aside w/two 12mm bolts
3. Using a small flathead screwdriver, pop out the 'SRS' button cover from the C pillar panels on the left & right hand side to access either the phillips head screws, 10mm bolts, or #30 Torque Screws
a. Remove screws and set aside
b. Using a standard flathead screwdriver, pop out the C pillar panels on both sides (clips hold these panels in place)
c. Set these panels aside after removal w/screws/bolts
4. Trunk Access-way panels are held in place by phillips head screws (two at the bottom (left and right hand sides) and 4 to 5 at the top .
a. Remove left and right hand panels and set aside w/screws.
5. Rear package deck held in place with two plastic clips (white, yellow or pink)
a. lie on your back inside the trunk (trunk lid open to allow for more light). Looking through access hole find 3rd brake light wire harness connector & disconnect.
b. locate package deck clips, one on the left and another on the right on the underside of the pckage deck
c. Squeeze clips to push them out - package deck will come loose
d. Remove package deck & remove 3rd brake lamp bulb socket (turn counter clockwise to remove). Replace bulb & reassemble in reverse order.

Sep 05, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

Rightside, rear window motor failed. or the mechanical part perhaps. what i want to know is how to get to that part of the car. The driver seat behind the panel. Thank you wery much! Patrik


Long job and not for the faint of heart.

Open roof to rear.

Pull up on rear seat bottom and remove it.

Remove center panel.

Remove three Allen head bolts down behind seat cushion back.

Lift off head rests...pull up.

Raise top just enough to make side flaps flip up.

Remove nut at top rear corner.

Remove Nylon/plastic push lock rivet where seat belt goes through panel... top corner.

Pull panel off mounting pins...will sound like your breaking it !

Lift panel to access seat belt bolt and unplug Flip-Up panel motor.

Remove cable from it's clip.

Remove loom thro' panel.

Pull seat belt thro panel.

Set panel to one side.

Remove Torxs bolts around black plastic panel for speaker.

Unplug speaker.

Pull loom thro' hole.

Remove two Allen and 5 hex bolts where window would come out. if it worked.

Pull up plate and remove rubber seal to one side and then remove plate. remove two nuts at bottom of regulator and one half way up towards front.

Lift regulator and window glass up thro' top to gain access to three nuts holding glass tho regulator.

Lift out window and then regulator....little maneuvering and levering required.

FYI....Take digital pictures as you remove stuff for later reference.


New regulator and glass is around $600.00 from dealership and only the dealership.

Jan 12, 2011 | 2004 Volkswagen New Beetle Convertible

2 Answers

I want to upgrade the speakers by the back window but want to know how to remove the carpet to get to the speakers.


dont remove the carpet you will have to remove the stock speakers from inside of the trunk

Oct 22, 2010 | 2003 Mitsubishi Galant

3 Answers

How to replace 2004 bmw z4 hood emblem


if it's regular emblem , then it has two plastic pins on the sides (Left and right , very tight fit), it's almost impossible to pull emblem out without braken it.
hood has two plastic clips ,were those pins go.

Apr 18, 2010 | 2004 BMW Z4

1 Answer

Remove rear side marker on 03 z4


I need to change headlight bulb in a 2004 BMW Z4 coupe. Does anyone know where I can find out how?

Nov 18, 2009 | 2003 BMW Z4

1 Answer

Needing instructions for the removal of drivers side door panel on 2004 BMW Z4.


There are two screws that need to be removed from the front door panel as well as the clips--the screw under the little plastic cover beneath the inside door handle, and an additional screw on the inside of the door, accessible when you open the door up--if I recall correctly, you should see a screw in or near where the air duct is located, where the air blows from your console into the air duct of the door. Hope this helps! There is also a row of metal clips on the top of the panel, which are different than the plastic clips surrounding the rest of the door panel.
Check the below link it may increase your knowledge on your car. http://www.youtube.com/watch?v=zEZ-bcEYdRA&feature=player_embedded#t=12

Sep 22, 2009 | 2004 BMW Z4

2 Answers

My Audi A4 drivers seat side control panel has come off. How can I fix it? can I get the replacement panel? Thanks, AJ


1) The Electrical panel on the side has a black bar that is the mounting bracket. It is only clipped in place on the plastic outer casing. the black metal bar is attached with 2 shoulder screws. these probably just worked themself loose nad dropped out. Go to your dealer parts counter and ask them for the 2 screws. Remount the black bracket and then re clip the case to the bar.

Jun 18, 2009 | 2004 Audi A4

1 Answer

How much is the cost for 60,000 km maintenance for Z4 2004?


there's an old saying ...if you have to ask you can't afford it.  These answers are all dependent on what the brakes and the services require as well as what the repair shops in your area charge for these services.  So any answer given at this time would be totally useless. Sorry
However, the two mentioned service will be expensive.

Nov 21, 2008 | 2003 BMW Z4

2 Answers

2003 volkswagen beetle covertible quarter panel removal


I do not recommend this job unless you are a seasoned mechanic, VW dealership charges $1000 for a reason. They almost earn it on this one. but heres how it's done or how I did it any way. the complete job took me 4 hours and I been at this for 30 years. But a lot of this time was figuring out how it came apart. First, drop the top, pull up on seat bottom and remove it, remove center panel, remove 3 allen bolts at bottom on seat back and remove. headrests, they just pull off, raise top just enough to make hinged panels flip up. remove nut at top rear corner of side panel. you can see the back side of the nut and bolt it is on from the panels that flip up. Remove Nylon push lock rivet where seat belt goes through panel on rear, top, corner. Pull out on panel to release it, there is 5 or 6 nylon locks that just pull out of holes in the body. It will sound like your breaking it when the locks pop loose, or mine did. then lift to gain access to remove seat belt bolts and unplug flip panel motors. remove cable end from its clip. Pull seat belts through panel. Set panel a side. remove torx head bolt around oval panel that speaker is mounted on. unplug speaker and regulator and pull wire harness thru hole. remove 2 allen and 5 hex bolts at top where window would come out if it worked. pull up on plate and move rubber window seal to the side to remove plate. remove 2 nuts at bottom of regulator and one about half way up towards front, lift regulator and window up through top to gain access to 3 nuts that hold window to regulator, from the top lift window out first then regulator. Reverse to assemble it.

Aug 12, 2008 | 2003 Volkswagen New Beetle Convertible

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...