Question about 1999 Chrysler 300M

1 Answer

P 0340 what does that code mean

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 14,363 Answers

Here's a link to your code Joe/

Posted on Jul 10, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 0340 code for my cam shaft


Well code 340 means the cam sensor is not working correctly. The engine computer is not getting the signal it expects.
The sensor and the wiring would need to be tested.

Feb 19, 2015 | 2005 Mazda 6

1 Answer

I have a 03 dakota I did a 5.9 swap from a 3.9 I finally finished I have the 03 pcm and harness It will start for 5 seconds then shuts down has a 0340 and 1686 code any suggestions?


the 1686 isnt a ford code but the 0340 is the cam position sensor may be a wiring fault or the sensor its self ,gives you a starting point as this would give the symptoms you describe

May 01, 2014 | Cars & Trucks

1 Answer

Chevrolet Aveo 2004 Error code 0340


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the ECM if this was helpful please leave good feed back

Jun 28, 2013 | Cars & Trucks

1 Answer

P 0340 i changed it and it still wont start


The code is for the cam sensor, but it does not always mean the sensor is defective.
It means the computer is not getting a signal from the sensor.
Causes can include wiring problems between the sensor and the computer, and mechanical problems with the camshaft or timing belt.

Jul 07, 2012 | 2006 Dodge Stratus

1 Answer

Need to know what dodge codes P0325, P0344 & P0340 mean


0325 knock sensor
0344 cam position sensor intermittent
0340 cam position sensor failure

I would replace the cam position sensor from the codes you provided. The knock sensor
would most likely be related to the sensor failure.

Jun 28, 2011 | Dodge Neon Cars & Trucks

1 Answer

Code p 0457 and code p 0340 what do these codes mean?


Code P0457 is an Evaporative Emission System Leak Detected. Often this code can be triggered by a fuel cap that is not installed properly. It can also be cause by a bad EVAP control solenoid. Inspect the fuel lines and hoses to make sure there are no cuts/breaks etc. If the fuel cap is good then you'll have to replace the EVAP solenoid.

Code P0340 is a bad camshaft position sensor in bank 1. You'll need to replace that in order to clear the code.

Aug 12, 2010 | 2006 Chrysler Sebring

1 Answer

My 07 pt cruzer engine light is on so i did the off on off on and the code that came up was p 0340. what does that code mean?


Try the dealer, call the service department for a correct answer. It probably is just the pre-programmed normal engine check for the catylic converter. These lights usally go on about 50K miles, then it makes you panic and send it to the dealer. He then flips a little switch under the dash to make it go out until the next 50K miles goes by, then he checks the converter for clogging or such and then charges you. Without knowing the code meaning, this is what I would suspect it to be.

May 12, 2010 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

Car Stalls at low speed. Restarts. DTC Code 0340 and 1167


The codes you provided indicate separate issues. Code 1167 is indicative of either a stuck fuel injector of the O2 sensors. Code 0340 indicates the CMP position sensor. Replacing the O2 sensors will likely clear the 1167 code assuming the fuel injectors are okay. It would be the first course of action. If there's no noticeable change in performance (i.e. stalling problem continues) then the CMP position sensor is likely your overall problem. Best of luck.
Greg

May 25, 2009 | 2003 Nissan Maxima

1 Answer

Problem codes


1391-loss cam and\or crank signal
0352-ign coil2 mal
1698-no etax ccd messages
0340-cam sensor signal mal

Aug 25, 2008 | 1997 Dodge Stratus

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...