Question about 2001 Dodge Dakota

Open Question

How to bleed the clutch master cylinder on 2001 dakota

Slave cylinder was removed and all air is bled from it. The mastercylinder still has air. how do I bleed it?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
freetek
  • 5568 Answers

SOURCE: hydraulic clutch bleding 1999 dodge dakota

Please take a look at my suggestion here:

http://www.fixya.com/support/t709796-nissan_240sx_1997_se_model

Posted on Jun 30, 2008

Ad
  • 190 Answers

SOURCE: How do I bleed the clutch slave cylinder on a 1993

should be self bleeding if pedal is set correct

pedal rod needs 1/8" free play to clutch master clydinder plunger

fill clutch res slowly let bubbles bleed

then only half strokes on the clutch pedal with 30sec pause between pumps

Posted on Mar 19, 2009

  • 1 Answer

SOURCE: 1999 Dodge Ram 3500 Pickup - Clutch

use a hand vacumn and cover over the reservoir, apply light vacumn and the air will come to the reservoir, usually take 2 or 3 time and the air will work back out to the top,

Posted on Apr 16, 2009

  • 1 Answer

SOURCE: Hyd. Slave cylinder WITHOUT bleeder

you have to replace the master and slave. if there is no bleeder, you might get lucky bench bleeding it, but the whole assy, comes from dealer pre-bled. The system is sealed and even to do a clutch or trans, you shouldnt have to take it apart. DO NOT PUSH CLUTCH WITHOUT ALL PARTS HOOKED UP! youll break it.

Posted on Apr 21, 2009

  • 1 Answer

SOURCE: dodge dakota

i have a 2000 dodge dakot and can not bleed the slave cly how do i do it

Posted on Jul 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

New clutch not disengaging


When I do clutch jobs. I replace the clutch package(comes with the slave) and the master cylinder also. Have the flywheel turned or replaced. Just a note. The clutch plate can be installed backwards. No matter how many times you bleed it, It won't work.

May 30, 2016 | 2001 Dodge Ram 3500 Truck

1 Answer

Replaced throw out bearings on 1996 dodge Dakota/ v6,do i bleed clutch also,if so how.


if the slave cylinder remaine intact on the hose from the master cylinder then there is no need to bleed the system
if the slave cylinder was inside the bell housing and you ahd to remove a hose to get the box out then yes it has to be bled and by the bleed niple on the sode of the bell housding
bleeding procedure is as per any hydraulic system

Jul 07, 2015 | Dodge Cars & Trucks

1 Answer

Piston on new slave cylinder not moving


Gravity will not bleed the system as you need pressure in the master cylinder to bleed out the air. Once you have pressure bled the system you will have a good clutch

Nov 16, 2013 | Chevrolet S 10 Cars & Trucks

1 Answer

I have a 1988 f350 diesel i replaced the clutch master cylinder and the slave cylinder bled the lines and the truck still wont go in gear the throw out arm is moving about 1/2 inch what could be my prob


Ford has special bleeding and blocking instructions for clutch slave. Check manual for proper bleeding requirements. May consider presurre bleeding of master cylinder or use master cyclinder bleeding tubes that fill the resevoir as you bleed the and remove all air in system.

Jan 21, 2013 | Cars & Trucks

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

1 Answer

I have a 1996 f150 4x4 5 speed v 4.9 engine that the clutch mastercylinder has to be pumped up before you can put vehicle in gear. It has a new clutch mastercylinder should I change out the slave cylinder?


did you bleed the slave cylinder? On the slave cylinder there should be a bleeder screw just like a brake caliper, perform the bleed procedure just like a brake, pump clutch and open slave bleeder, repeat untill all air is no longer noticed. keep master filled with fluid and top off when completed

Mar 09, 2011 | 1996 Ford F150 Regular Cab

1 Answer

1987 Maxima-5 speed is difficult to grt in to gear--How to adjust clutch and check clutch hydraulic fluid?


TO ADJUST PEDAL HEIGHT ADJUST WITH A STOPPER LIMITING THE UPWARD TRAVEL OF THE PEDAL.PEDAL FREE PLAY IS ADJUSTED AT THE MASTERCYLINDER PUSH ROD.IF PUSH ROD IS NON ADJUSTABLE FREE PLAY IS ADJUSTED BY PLACING SHIMS BETWEEN THE MASTERCYLINDER AND THE FIREWALL.ON A FEW MODELS PEDAL FREE PLAY CAN ALSO BE ADJUSTED AT THE OPERATING SLAVE CYLINDER PUSHROD.PUSHRODS ARE AVAILABLE IN THREE LENGTHS FOR THE 310.PEDAL HEIGHT ABOVE FLOOR IS 6.73 - 7.13 INCH PEDAL FREE PLAY IS 0.04 - 0.12 INCH.YOU HAVE CLUTCH FLUID LONG AS YOU SEE BRAKE FLUID IN MASTERCYLINDER.IF MASTERCYLINDER LOW YOU HAVE TO BLEED THE THE CLUTCH MASTERCYLINDER BY LOCATING BLEED SCREW ON SLAVE CYLINDER. REMOVE THE BLEED SCREW DUST CAP.ATTACH A CLEAR TUBE TO THE BLEED SCREW.PUT OTHER END OF CLEAR TUBE IN A CLEAN CONTAINER OF BRAKE FLUID.FILL THE MASTERCYLINDER WITH BRAKE FLUID.OPEN BLEED SCREW 3/4 A TURN.DEPRESS CLUTCH PEDAL QUICKLY.HOLD IT DOWN.HAVE A HELPER TIGHTEN THE BLEED SCREW.ALLOW PEDAL TO RETURN SLOWLY.BLEEDER SCREW TORQUE IS 5 - 6 FT LBS.IF YOU SEE AIR BUBBLES CLEAR BLEED TUBE.REPEAT THE BLEED PROCESS UNTIL YOU SEE NO AIR BUBBLES.DONT LET CLUTCH MASTERCYLINDER GO DRY WHILE BLEEDING.IF SO YOU GOT START BLEEDING PROCESS ALL OVER.HOPE THIS HELP.

Aug 05, 2010 | 1987 Nissan Maxima

1 Answer

Replaced master cylinder and cant get air to bleed out


If you have been bleeding it correctly(it is bled using same procedure as brakes just with the clutch pedal) you might need the clutch slave cylinder. It does take a good couple hours to bleed one of these using the conventional two person method so it could still need bleeding but if it is taking to long and your initial symptoms were brake fluid disappearing and you could not visually see the leak from a line or master cylinder then it is leaking from the clutch slave cylinder located in between the clutch and transmission. The transmission would have to be removed.

Oct 29, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

I replaced my slave cylinder and i still have to pump the clutch to shift.what is my problem.


did you bleed out all the air?? if so and you still dont have pedal, then you will need to replace the clutch master cylinder.

Sep 27, 2009 | 1988 Mazda B2600 Cab Plus

1 Answer

Hyd. Slave cylinder WITHOUT bleeder


you have to replace the master and slave. if there is no bleeder, you might get lucky bench bleeding it, but the whole assy, comes from dealer pre-bled. The system is sealed and even to do a clutch or trans, you shouldnt have to take it apart. DO NOT PUSH CLUTCH WITHOUT ALL PARTS HOOKED UP! youll break it.

Mar 21, 2009 | 1999 Dodge Dakota

Not finding what you are looking for?
2001 Dodge Dakota Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...